Laserfiche WebLink
<br />1 Under!ayment: Standard Slope-:4112 (333mm/m) or more . <br />ApplicatIOn of underlaymenl: Cover deck with one layer of underlayment Installed without <br />wrinkles, Use only enollgh nails to hold underlayment in place until covered by sllingles, <br />Application of eave !lashing: Install eave flashing such as GAF Materials Corporation Weather <br />Watch" or StormGuard~ Leak Barriel in localities where leaks may be caused by water backing <br />up behind ice or debris dams. Eave flashing must overhang the roof edge by 3/8" (10mm) and <br />extefl{j 24" (610mm) beyond the inside wall iine. <br /> <br />4" CJ(j;?mm)I......--~-__ <br />1?" (305mm) <br />Minin1tilTl Slone. <br />For lowor slopes, see Box i a <br /> <br /> <br />i <br />I <br />i\1i shec\s are ::\6" (914mm) <br />'Nkit'! Shinqh.~~Mf.lte~ <br />und0da:~/T'-ient <br /> <br />:!" (51mm) Side Lap <br /> <br />~ 4" (102I'llm) End Lap <br />...7'~AI_..... <br />-;:/ L..._ AI()n~l eaves put underli:l..yrnant <br />on top of motal drip edgu. <br /> <br />r <br />Ar~)ng rako, plaoJ <br />dnp l;!dge on top <br />of lmdcrlayrrHHlt. <br /> <br />2 <br /> <br />Starter Course <br />Apply as sllOwn. <br /> <br />Start at either rake and <br />lay in either direction <br /> <br /> <br />('~"" <br /> <br />For {1l<<xirnUr;l wind re5i:;lantf' <br />aic~g rakas, cement shingles <br />10 lJndi~rhymB~l~ !trod e<l,~i1 <br />other!n a 4" (1C2mm) w:dth <br />,r asph.~:t pl,iSk: !:lOt (:,~lrH~!~t, <br /> <br />r,irn 6"{1S2mrn\ <br />frum ond of ' <br />fir5t shin!lie <br /> <br />4 Second Course <br />Start and continlle second course as sllOwn. Trim 6" (152mm) from the end of the <br />shingle, Position the shingles in the second and subsequent courses flush with the tops <br />()f the wide cutouts, This results in a 5" (127mm) exposure, Continue with full width shingles <br />across the roof. Strike a chalk line about every 6 courses to check parallel alignment with <br />eaves. NOn:: Shingles may be laid from either <br />left or right hand side. Start at either rake <br /> <br />eage with slllngles IJaving 6" (152mrn) <br />trimrned from rake. <br /> <br /> <br />rr:rn Shinglu:; <br />:." (152~I\rnl <br /> <br />6 <br /> <br />Fourth and Remaining Courses <br />Trim 17" (432 mm) from tirst sningle m the course, then continue with full shingles across <br />the roof. ~Ifth and subsequent courses repeat full shmgle mstructions from Step 3. <br /> <br /> <br />, <br /> <br />j' <br />rri!m'fi0U Shinyill$ <br /> <br />"a Underlayment: Low Slope 2/12-4/12 C167mm-333mm/m) . <br />.' Application of underlaymenl and eave flashing: bompletely cover the deck With two <br />layers of underlayment as shown, Use only enough nails to hold underlayment in place <br />until covered by shingles. Use blind nailing for eave flashings. At eaves and where ice dams can <br />be expected, use one layer of GAF Materials Corporation Weather Watch" or StormGuard~ Leak <br />Barrier, Eave flashing must overhang the roof edge by 3/8" (10mm) and extend 24" (610mm) <br />beyond the inside wall line. Where ice dams or debris dams are not expected, install 2 plies of <br />Sllingle-Mate~ underlayrnent. <br /> <br />Low slope <br />(51mmto 1~'~~~; ~ <br />f 2" (30Srnm) <br /> <br /> <br />Nl sheel,> ar~ ;~6" (914mm) <br />wide Shif\gltl-MatA~ J <br />un,jerlayment. <br /> <br />Flaim drip edge <br /> <br />3/B~ (10mrn) Hoof overhang <br /> <br />3 <br /> <br />First Course <br />Start and continue with full shingles laid flush with the starter course, Shingles may be <br />laid from left to right or right to left. DO NOT lay shingles straight up the roof since this <br />procedure can cause an incorrect color blend on the roof and may damage the shingles. <br /> <br /> <br />Slart'ir;;1 \.OUf$f1with who/", <br />... $hingltl plllCco 3/8" (lOmftl) <br />o'lar eave and rake edqilS <br />lilPm..idu<itip!l(lijEl <br /> <br />5 <br /> <br />Third Course <br />Trim 11" (279mrn) from the first shingle in the course 1hen continue with full shingles <br />across the roof. <br /> <br /> <br /><<" <br />.<fl<;l~...', <br />\'\.... ..' <br />, ., <br />", "/', <br /> <br />1" ',..' <br /> <br />Trirnnwd Stlinglu,s <br /> <br />rusl Cour!,.lU <br />[-:ull ShillUl11 <br /> <br />7 Hip and Ridge <br />For single layer application, lIse hip and ridge shingles and apply as shown. To enhance <br />appearance, lIse GAF TIMBERTEX~ (one bundle of TIMBERTEX' Hip & Ridge covers 20 lin- <br />eal fl.-6.1 meters) or a double layer application of Universal Hip & Ridge. For double application, <br />start with triple thickness of precut Hip & Ridge shingles and continue remainder with <br />double thickness. Fasten in same manner as single application shown. Apply laps away from <br />prevailing wind direction. <br /> <br />8" (203rnm) exposure <br /> <br />Bend Hip & Rid9D ;;hingla <br />centered ovp.r Hip or Ridge <br /> <br /> <br />TIMBEFlTEX" <br />Hip & Ridge <br />'" <br /> <br />4T\ <br /> <br />.~ <br />t <br /> <br />5' (iUI"lrnj <br />e)(p0S\~re <br /> <br />Nail 5-5/8" {143rnrnj <br />IrolTi bottom and <br />1'- (25mm) from edge <br />