|
y n • r ' ° �� v
<br /> {$ r •
<br /> 4
<br /> rats t om.
<br /> a rt' -v, ::-5,--7:-.1-7',7---'. t � 01 # t,yt- '<_s 'V -, i :'. S f c 1 ..,.& 4 w � . f '',' ur n a j '' tx • ~g .li, ' '
<br /> i v ��_ METAL SYSTEMS INC. `
<br /> 4
<br /> GALVALUME WARRANTY m
<br /> k . -V METAL SYSTEMS INC. warrants to the buyer that METAL SYSTEMS INC.'S hot dipped aluminum -zinc alloy coated t'
<br /> f k *' . , 7' GALVALUME (T) sheet steel sold for use as unpainted steel building roofing and siding panels, if erected within the k. + f
<br /> i.;., United States, will not rupture, fail structurally, or perforate within a period of 20 years after shipment from METAL ,. r
<br /> SYS TEMS INC. due to exposure p
<br /> ' posure to normal atmos heric corrosion ter ....,,e,.§1
<br /> -.0 # � , This warranty My DOES NOT APPLY to sheets ex posed at any time to corrosive or aggressive atmospheric conditions
<br /> including but not limited to: E
<br /> F 1. Areas subject to salt -water marine atmospheres or to constant spraying of either salt or fresh water.
<br /> ;� 2. Areas subject to fallout or exposure to corrosive chemicals, fumes, ash, cement dust or animal waste. 1
<br /> k �• 3. Areas subject to water run -off from lead or copper flashing or areas in metallic contact with lead or copper.cs< Wit.
<br /> ' y ` 4 Conditions/circumstances where corrosive fumes or condensates are generated or released inside the ,,
<br /> building. *x d am ,
<br /> a"' `,,,,i.. ' This warranty DOES NOT APPLY in the event of: ' ,":,��''
<br /> • : 1. Bends less than 2T for sheet thickness 0.030 and thinner and less than 4T for sheet thickness 0.031 and
<br /> 4 { - . s - thicker.
<br /> s { ' , 2. Slopes of the roof or sections of the roof flatter than V.:12.
<br /> tt
<br /> ‘ , r 3. Mechanical, chemical, or other damage sustained during shipment, storage, forming, fabrication, or during ,
<br /> or after erection. >
<br /> -� � : 4. Forming which incorporates severe reverse bending or which subjects coating to alternate compression '. ,
<br /> ' and tension. ,4 r
<br /> ` pr 5. Failure to provide free drainage or water, including internal condensation, from overlaps and all other
<br /> ` `
<br /> ' 43-r :
<br /> Tr `
<br /> surfaces of the sheets or panels. w �
<br /> 6. Failure to remove debris from overlaps and all other surfaces of the sheets or panels. .
<br /> �� .. 7. Damage caused to the metallic coating by improper roll forming, scouring or cleaning procedures. : ,
<br /> , ;z.:. 8. Deterioration of the panels caused by contact with green or wet lumber or wet storage stain caused by ` ;;
<br /> {
<br /> '"' :{ # water damage or condensation. 4Y y
<br /> r ► 9. Presence of damp insulation or other corrosive materials in contact with or close proximity to the panel -W
<br /> 10. This warranty does not apply in the event of deterioration to the panels caused directly or indirectly by ' t
<br /> r ' panel contact with fasteners. Selection of suitable long- lasting fasteners to be used with Galvalume '
<br /> k roofing and siding panels rests solely with the Buyer.
<br /> +rte , 5 = � r .
<br /> ti 4 Y1 ; y • y
<br /> 1, This warranty shall be subject to the stipulations, limitations, and conditions hereinafter set forth: "° =� W ;f
<br /> iF k cik+aa;
<br /> �,,
<br /> ,,-,...1,-,,, X , 1. Metal Systems, Inc 's liability for breach of this warranty shall be limited exclusively to the cost of either repairing ; °= : -7::-, :
<br /> s11 A � i I , r onconformieg panels, or at Metal System's Ire's sole options of frnishirg FOB Bayer's plaid sufficient sheet
<br /> = r eroded to enable Buyer to fabricate replacement panels for the rorcorforming panels. � -
<br /> . . 2. Metal Systems, Inc shall rot it any event be liable for the cost of tabor ezperded by others on any noeweformirg 1'
<br /> sheet or for ar
<br /> V l '' special, V. any spec' , indirect or consequential damages
<br /> 17 i'' have beer Nonconforming. to ar ywe by reasos of the fact that such panels shall b e rb ,
<br /> A , '' 3. Claims must be promptly reported in writing to Metal Systems, Inc. and Metal Systems, Inc. shall be giver a .
<br /> reasonable opportumity to inspect the pate's claimed to be nonconforming. Adequate idertificatios of the material � Y Z v i .
<br /> ti , mvohred In the daim, irdrding date of iastallatior, Metal Systems, Inc. order number, invoice number, and date of V? ?-;
<br /> shipment must be established by Buyer. _
<br /> ;s* 4. Buyer shall exercise diligence in inspection of sheets as received from Metal Systems, Inc. so as to mitigate repair 7 ' t„r fix
<br /> _ or rep +�
<br /> " 5. Metal S ystems, Inc. extends this warranty solely to the Buyer. This warranty is eon- transferable and non- 1 '
<br /> assigeable Vs 1 :.
<br /> '''' e
<br /> 6. Metal Systems, Inc . reserves the right to terminate this warranty at any time (expect as to orders already accepted)
<br /> Epee the giving of written notice thereof. a
<br /> x; , 'tea s ,
<br /> :. ; i , METAL SYSTEMS, INC. MARES NO GUARANTEES EITHER EXPRESS OR IMPLIED BEYOND THE FACT HEREOF INCLUDING, WITHOUT : • : a.
<br /> `{ „ ' LIMITATION WARRANTIES OF FIT AND MERCHANTABILITY MW SHALL HAVE NO OTHER LABILITY WITH RESPECT THERETO. �=- `,
<br /> i A pr r i
<br /> ti ,
<br /> a <
<br /> to ' y sx,. ®. ti+ ,.r s... 4'4" ` » �,��, } , � w s L � " car h "
<br /> `its" ' ' ' 11
<br /> : , y, - ,, • -. , Z " F' - L ' � �' -^.'"-_,,,,...;-''1'7 c. . •off 3, ice, [}
<br /> ,it " 46",4,,'6.'?` . - - . • A -. i„ ..� �,:tM .. sF1
<br />
|