09-9360 - Laserfiche WebLink

Browse Search

4. ( iSDoor DOOR INSTALLATION INSTRUCTION( . & i Components STEP 12 CHECK THE DOOR FOR PROPER SPRING BALANCE. . r 1 � COLD DOORS ri / IF DOOR LOWERS . EASY AND RAISES HARD, MORE SPRING TENSION ' °� NOTE /4: IS REQUIRED. ' :"-• ®� , ?. �� O TO INSIDE OF GUIDE �" BOL HEAD IF `i" LOWERS HARD AND RAISES EASY, LESS SPRING TENSION LH ° : � IS REQUIRED. :in`' iJl� ` �� �� PROCEED TO STEP 13 IF ROLL UP DOOR IS NOT BALANCED. 1 ` I' �L / 000R CURTAIN WINDING BAR 1 /4 "CARRIAGE BOLT PLACE WINDING BAR 1 HEAD STOP CHANGING POSITION OF AXLE IN THROUGH BOTH SIDES ' ✓ THIS DIRECTION DECREASES LIFT OF AXLE AS SHOWN. �, j 1' 1 /4 "NUT l e III ADJUSTMENT HOLE HEADER . r INSTALLER FIGURE 7 1 STEP 7 O WITH CURTAIN STILL IN GUIDES, INSTALL HEAD STOPS WITH ONE 1/4" BOLT AND ONE 1/4 "NUT FOR EACH STOP AND TIGHTEN. p ' CHANGING POSITION OF AXLE IN THIS DIRECTION INCREASES LIFT FINGER LEVER _ O® n 1r LH BRACKET 10 11 I / �PI T N 1 DOOR GUIDE "LEAD IN" LIFT HANDLE / ~ � �I / � -�®' BOTTOM AR STOP � / FIGURE 13 STEP 8 FIGURE 8 INSTALL LIFT HANDLES WITH TWO 1/4" CARRIAGE BOLTS AND NUTS ON CAUTION OUTSIDE OF DOOR AT CENTER AND L.H. SIDE OF DOOR, ALSO INSTALL USE A PROPER ROUND 1/2 DIAMETER STEEL WINDING BAR OF STOP PLATES AT EACH END OF BOTTOM BAR WITH 1 BOLT EACH AS SHOWN. SUFFICIENT LENGTH TO COMPLETE FINAL ADJUSTMENT ON THE DOOR SPRINGS IF DOOR HAS MINI LOCK, LIFT HANDLE SHOULD BE LOCATED ON BOTTOM BAR DIRECTLY BELOW LOCK ASSEMBLY, SEE STEP 9 IF SLIDE BOLTS ARE PROVIDED. STEP 13 RAISE DOOR TO 12" FROM FULL OPEN POSITION: ADD ADDITIONAL SPRING NOTE: GUIDE MUST HAVE BOTTOM TENSION WITH WINDING BAR IF DOOR IS COLD. DOOR WILL START TO RAISE G. - , NOTCHED FOR SLIDE BOLT ON ITS O WN WHEN BALANCE IS COC FIGURE 13). REMOVE E XCESS SPRING TENSION WITH WINDING BAR BY LIFTING ADJUSTER , SPACERS PAW WITH FINGER LEVER ON OUTSIDE OF BRACKET AND SLOWLY RELEASING "DIA. = (5/16 "JAM NUT) SPRING TENSION 1/6 TURN AT A TIME IF YOUR DOOR IS HOT (SEE FIGURE 13). BOLTS I /�� 11 /4 "DIA. ■ 0 V e FLAT WASHER STEP 14 8 GA. GAL.. STEEL t:. n CYCLE THE DOOR UP & DOWN A MINIMUM OF 5 TIMES; NOW SLIDE BOLT LOCK k:, CHECK CHECK DOOR FOR PROPER BALANCE. REPEAT STEP 13 IF NECESSARY. (OPTIONAL) 3/8" WASHER , �/ I 4 "DIA. STEP 15 IF DOOR DRAGS IN GUIDES: (A) CHECK DOOR MOUNTING FLAT PLATE �NUTS BRACKETS FOR PLUMB. (B) ADJUST LOCATION OF GUIDES FOR P/N U320023 3/8" CLEARANCE FROM CURTAIN ROLL END TO INSIDE OF VERTICAL FIGURE 9 MATTER, SUCH AS DIRT, ETC. CO (D) CHECK CHECK STEP 9 LEAD -IN BEND AT TOP INSIDE OF GUIDES ( "LEAD IN" SHOWN IN FIG. 13). INSTALL SLIDE BOLTS (IF SUPPLIED) WITH BOLTS AND HARDWARE ON INSIDE OF DOOR, WITH STOP PLATE AS SHOWN IN FIGURE 9. STEP 16 IF DOOR DOES NOT CONTACT FLOOR LEVEL: (A) USE SPIRIT LEVEL TO CHECK WHETHER DOOR OR FLOOR IS OUT OF LEVEL. (B) CONFIRM DOOR SUPPORT BRACKETS AND GUIDES ARE LEVEL. (C) ROLL DOOR ALL THE WAY UP AND STEP 10 CHECK IF CURTAIN ROLLS STRAIGHT ON DRUMS, END OF DOOR SHOULD BE SQUARE. BOLT GUIDE RAILS TO BUILDING. KEEP 3/8" CLEARANCE STEP 17 FROM CURTAIN ROLL TO INSIDE OF VERTICAL DOOR GUIDE. SECURE ALL FASTENERS AND CHECK FOR PROPER LOCK OPERATION. RECOMMENDED SERVICE 1. LUBRICATE THE INSIDE OF DOOR TRACKS AS REQUIRED. /► 2.CHECK ALIGNMENT OF HEAD STOPS AND TIGHTEN ATTACHING NUTS AND BOLTS. 3. CHECK AND TIGHTEN ALL NUTS, BOLTS AND SCREWS ANNUALLY, THIS BOTTOM BAR 4. MAY BE REQUIRED MORE FREQUENTLY FOR HIGH CYCLING DOORS. INSIDE PULL ROPE 5. USDOOR RECOMMENDS: SERVICING ANY PART OF COUNTERBALANCE SYSTEM INCLUDING SPRINGS, DRUMS, AND AXLE BE PERFORMED BY FIGURE 11 QUALIFIED DOOR SERVICE PERSONNEL ONLY, USING USDOOR PARTS OR APPROVED EQUAL. IMPORTANT SAFETY NOTICE STEP 11 1.OPERATE DOOR ONLY WHEN PROPERLY ADJUSTED AND FREE OF OBSTRUCTIONS. DROP PULL ROPE THROUGH HOLE IN CENTER OF BOTTOM BAR 2.00 NOT PERMIT CHILDREN TO OPERATE OR PLAY WITH ROLL UP DOOR. AND KNOT BOTH ENDS OF ROPE (SEE FIGURE 11 ABOVE). 3.SHOULD DOOR BECOME HARD TO OPERATE, CONTACT A QUALIFIED DOOR AGENCY. PART No. U160033 rev. 01.03.08 cdw