Laserfiche WebLink
to - <br /> S <br /> -0 <br /> ', Project No. T138 -03 - ' �` Page 3 of 5 <br /> .�, ag <br /> IFI ';, Product Description <br /> : : <br /> ,t � . General: <br /> 0 Test sample was comprised of Goren Model "G5305" (.downsize)Tilt Double Hung Vinyl <br /> Prime, one- over -one (tilt loading type) double hung window, with an overall master frame <br /> K size measuring 44" wide X 60" high X 3 -1/4" wide. The bottom sash measured 40 -1/8" <br /> i wide X 29 -1/2" high overall. The top sash measured 39 -1/4" wide X 28 -5/8" high overall. <br /> ,, The frame corners were of welded mitered with one screw in bottom comers construction. <br /> ,. The sash comers were of welded mitered type corner construction.. Bottom sash had an <br /> 1 ' aluminum exterior screen. Each sash had (2) foam chimney blocks located in the jambs near <br /> ¢ the balances. One foam chimney block for each side of each sash.. Each perimeter frame <br /> member hollows were filled with stirrofoam pieces that measured to be 7/16" x 9/16 ". The <br /> bottom rail of the bottom sash had a anti bow sway bar attached to the rail and when the <br /> i window would shut the bar would slide into an opening that was in the center of the sill. <br /> Weather stri e e in 1: <br /> I MEMBER WEATHERSTIPPING QUANTITY WIDTH X HEIGHT LOCATION <br /> r <br /> • Frame Header Insert Center Fin Pile Seal 1 <br /> I CHES <br /> � ` � Frame Sill 0.187" w x .23" ht side face <br /> none 0 <br /> Frame Jambs none 0 - none <br /> T, a sash — ■ e rail Center Fin -Pile Seal 1 - none <br /> Top sash =hot rail. 0.187" w x .23" ht exterior face <br /> Center Fin Pile Seal 1 0. I87" w x .23" 'ht <br /> • . , interior face <br /> Bottom sash — top rail Center .Fin :Pile Seal 1 <br /> meetin_ rail 0.187" w x .23" ht exterior face <br /> Bottom sash bot rail Center Pin Pile Seal <br /> 1 0:187" w x .23" ht Bottom face <br /> rail) Foam Filled Bulb Vinyl 1 0.3125" bia <br /> Bottom face <br /> with Fin <br /> Top sash — jamb stiles Center Fin Pile Seal 1 <br /> i � Center Fin Pile Seal 0.187" w x .23" ht Exterior face <br /> Bottom sash -jamb stiles' Center. File Seal 1 0.187" w x .23" ht Side face <br /> Center Fin Pile Seal 0.187" w x .23" ht Exterior face <br /> Screen - to. rail Pile Seal 0.187" w x .23" ht Side face <br /> ';� 0.187" w x .35" ht Interior face <br /> 9t t : <br /> Operators and Other Hardware: <br /> "F Each sash had two sets of (4)constant force balance shoes, one per jamb. One cam -type <br /> , sweep lock was attached to the center of the bottom sash meeting rail with kee <br /> sash meeting rail. One plastic tilt latch with - thumb actuator was housed at each end of the <br /> w, <br /> rail' and interior meeting rail of the bottom sash. One die -cast pivot bar was fastened (1 <br /> screw at each end of the bottom horizontal rails of the top and bottom sash. Each sash had (1) <br /> t lift rail with the top sash lift rail on the top rail and the bottom sash lift rail on the bottom r <br /> t <br /> , <br /> ':; rail. <br /> }r- <br />