|
Spacer h$tructions
<br /> D Iron ar P VC Pi pe,S zes AST`VI "2241.PVC Pi Sizes -(IPS O.D. ).
<br /> • For installation on
<br /> For installation on ‘,.:,:: '-' ' ASTM 2241
<br /> C900 PVC pipe, use ' —Leave sized pipe, remove E
<br /> as received and Spacer spacers and replace - Remove
<br /> install per p p „ , Spacer
<br /> p s crews. Install per '
<br /> instructions. ! instructions.
<br /> '�,
<br /> •
<br /> 3
<br /> 3
<br /> 1. Identify the pipe. The 2000PV is for use with 2 Clean the socket and the plain end. Lubrica- 3 Insert the pipe into the socket and press the
<br /> PVC and HDPE pipe. The 4 inch through 12 * Lion and additional cleaning should be provid- * gasket firmly and evenly into the gasket recess.
<br /> inch size may be used on C900, IPS, and C909 ed by brushing both the gasket and plain end Keep the joint straight during assembly.
<br /> PVC pipe as well as C906 HDPE pipe. Check with soapy water or an approved pipe lubricate 4 Push the gland toward the socket and center
<br /> to see if the spacers under the screws are meeting the requirements of ANSI /AWWA it around the pipe with the gland lip against
<br /> in place. If the pipe is C900 or is ductile iron C111/Al2.11 just prior to slipping the gasket * the gasket. Insert bolts and hand - tighten
<br /> O.D., proceed with spacers in place. If the pipe onto the plain end for joint assembly. Place the nuts. Make deflection after joint assembly but
<br /> is IPS 0.D., remove the spacers. Since 3 inch gland on the plain end with the lip extension before tightening bolts.
<br /> and 14 inch through 24 inch restraints are only toward the plain end; follow by the gasket
<br /> used with one pipe diameter, no spacers are with the narrow edge of the gasket toward the
<br /> used. plain end [The gasket provided may have been
<br /> the EBAA-Seallm Improved Mechanical Joint
<br /> Gasket. This gasket is bi- directional and has no
<br /> front or back. The use of a pipe wall stiffening
<br /> insert is required on High Density Polyethylene
<br /> pipe.].
<br /> NOTE: In cold weather it is preferable to warm
<br /> the :asket to facilitate assembl of the - oint
<br /> 04,:atiaoe
<br /> f s
<br /> �X
<br /> Pte ;, r . ± j:. 4 ° , t ' 4 _e .. K ;. , ., ,. t o r . z
<br /> 5 Tighten the bolts to the normal range of bolt 6 Tighten the torque limiting twist -off nuts in 7 If removal is necessary, utilize the 5 /e inch hex
<br /> * torque [45-60 ft-lbs for 3 inch, 75 -90 ft -Ibs for a clockwise direction (direction indicated by heads provided. If reassembly is required, as-
<br /> 4 inch through 24 inch, 100 -120 ft -Ibs for 30 arrow on top of nut) until all wedges are in semble the joint in the same manner as above;
<br /> inch and 36 inch, and 120 -150 ft-Ibs for 42 firm contact with the pipe surface. Continue tighten the screws to 60 to 80 ft -lbs. If the
<br /> inch and 48 inch.] while at all times maintain- tightening in an alternating manner until all of Series 2000PV restraint is removed from the
<br /> ing approximately the same distance between the nuts have been twisted off. pipe, be sure that all of the screws, spacers (if
<br /> the gland and the face of the flange at all required), and wedges are in place before the
<br /> points around the socket. This can be accom- *These steps are requirements of AWWA C600. restraint is reassembled.
<br /> plished by partially tightening the bottom bolt
<br /> first, then the top bolt, next the bolts at either EBAA IRON Sales, Inc,
<br /> side, finally the remaining bolts. Repeat the r. -, R z ,_ P.O.B0a857, Eastland, a 76448
<br /> p rocess until all bolts are within the a } * * .. . °ate A ern bers of ,. ....
<br /> appropri- �,�.
<br /> ate range of torque. In large sizes (30-48 inch) ,z"�1e'� w"!�•' „{Akay� , ' iek(254)62 &1731 FaC(254)629.8931
<br /> five or more repetitions may be required. The .,, ,,; (800) 433.1716 within US and Canada , x ,
<br /> COIItaCt@ebaa.COAI
<br /> use of a torque- indicating wrench will facilitate .,r i
<br /> the procedure. .� . , ..� , www.ebaa.wm , 3,4r,rca hi' r esssaucrsoorry
<br />
|