09-9335 - Laserfiche WebLink

Browse Search

SpectrAlert Advance Specifications Architect /Engineer Specifications General SpectrAlert Advance horns, strobes and horn /strobes shall mount to a standard 4 x 4 x 12 -inch back box, 4-inch octagon back box or double -yang back box. Two-wire products shall also !mount to a single -gang 2 x 4 x 11/4-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. the notification appliance circuit wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance products. when used with the Sync•Circuit" Module accessory, shall be powered from a non -coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync •Circuit Module, 12 -volt rated notification appliance circuit outputs shall operate between nine and 17.5 volts; 24 -volt rated notification appliance circuit outputs shall operate between 17 and 33 volts. indoor SpectrAlert Advance products shall operate between :32 and 120 degrees Fahrenheit from a regulated DE, or full-wave rectned, unfiltered power supply. Strobes and horn/strobes shall have field - selectable candela settings including 15. 5,/75, 30, 75, 95, 110, 1 1 , 1 35, 150, 177, 185, Strobe The strobe shall he a System Sensor SpectrAlert Advance fvlodel listed to Ul 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary - signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 liz. over the strobes entire operating voltage rands.-The strobe light shall consist of a xenon flash tube and associated lens/ reflector system. Horn /Strobe Combination The horn /strobe shall be a System Sensor SpectrAlert Advance Model listed to 01 1971 and 01 464 and shall he approved for fire protective service. The horn /strobe shall be wired as a primary- signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. he horn shall have three audibility options and an option to switch between a temporal three• pattern and a nor.-temporal (continuous) pattern. These options are set by a multiple position switch. On four -wire products, the strobe shall be powered independently of the sounder. The Horn on horn/strobe models snail operate on a coded or non -coded power supply. Outdoor Products SpectrAlert Advance outdoor horns, strobes and horn /strobes shall be listed for outdoor use by UL and shall operate between minus 40 degrees and 151 degrees Fahrenheit. The products shall be listed for use with a System Sensor outdoor /weatherproof back box with halt inch and three - fourths inch conduit entries. Synchronization Module the module shall be a System Sensor Sync•C ircuit model MDL listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn /strobe models over a single pair of wires. The module shah mount to a 4 4n1/26 x 21/4-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Physical /Electrical Specifications Standard Operating Temperature 32 °F to 120°F (0 to 49 °C) K Series Operating Temperature -40`F 10 151 (- 40 °C to 66t) Humidity Range 10 to 9355 non - condensing (indoor products) Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12DC /FWR or regulated 24DC/FWR' Operating Voltage Range 8 to 17.5V (12V nominal) or 16 to 33 V (24 nominal) Input terminal wire gauge 12 to 18 AWG Ceiling mount dimensions (including lens) 6 8 x 2.5 high (1 73 mm diameter x 64 rnm high) Wall mount dimensions (including Tens) 5.6 T x 4./W x 2.51? (142 rnm L x 119 mrn W x 64 mrn 0) Horn dimensions 5.61. x 4, 71N x 1.3 D (142 mm x 119 mrn W x 33 rnm D) Wail -mount back box skirt dimensions (BBS -2, BBSW -2) 5.9 "L x 5.0W x 2.2D (151 mm L x 128 mrn W x 56 mm 0) Ceiling -mount back box skirt dimensions (BBSC -2, BBSCW -2) 7 1-diameter x 2.25 "high (180 mrn diameter x 57 mm high) Wall -mount weatherproof back box dimensions (SA -WBB) 5.73 x 5.1 W x 2.0"D (145 rnm 1 x ( .' 1 mm W x 51 Him 0) Ceiling -mount weatherproof back box dimensions (SA -WBBC) 7.1 "diameter x 2.0" high (180 Harr diameter x 5' mm high) Notes; 1.:1r11 Wave Rectified (1 voltage is a non - regulated, time varying power source that is used on some power supply and panel outputs, 2. P. S, PC. and SC products will operate at. 12 '•1 nominal only for 15 and 15/75 cd.