Laserfiche WebLink
1 Product Information <br /> FS -ONE Product description FS-ONE <br /> • Intumescent (expands when exposed to fire) firestop sealant <br /> High Performance that helps protect combustible and non - combustible penetra- Technical Data <br /> bons for up to 4 hours fire rating At 73 °F (23 °C) and 50% relative humidity <br /> Intumescent Firestop <br /> Product features Chemical basis <br /> Sealant • Smoke, gas and water resistant after material has cured Water -based intumescent acrylic dispersion <br /> • Contains no halogen, solvents or asbestos Density <br /> • High fire rating properties Approx. 1.5 q/cm <br /> i u • Water based, easy to clean Color <br /> Red <br /> n , "" Areas of application Working time <br /> • Steel, copper and EMT pipes Approx. 0 -30 min. T <br /> Insulated steel and copper pipes Curing time <br /> �, • Cable bundles Approx. 4 mm / 3 days c-, <br /> 1 Closed or vented plastic pipes Shore A Hardness <br /> � Ad va n tage f c us t omer .Benefits • HVAC penetrations Approx. 35 <br /> • Protects most cal firestop For use with Movement capability <br /> penetra appp • Concrete, masonry, drywall and wood floor assemblies Approx. 5% <br /> • r Easy to work with and fast cleanup • Wall and floor assemblies rated up to 4 hours Intumescent Activation <br /> • Can be.painted Approx 482 °F (250 °C) <br /> • Stn le r om ent ava Examples Expansion rate (unrestricted): <br /> g � • Sealing around plastic pipe penetrations in fire rated Up to 3 -5 times original volume <br /> • Meets at 1'a indoor construction Temperature resistance (cured) <br /> m "x' • Sealing around combustible and non - combustible —40 °F to 212 °F ( -40 °C to 100 °C) <br /> Adh , Mar id 4.2 penetrations in fire rated construction Application temperature <br /> ;' Atlhesiv�. �rtd'4.�;Patttt5'ar>il'CtYatir� ' Pe Ap pe <br /> 41 °F to 104 °F (5 °C to 40 °C) <br /> Installation instructions for FS-ONE Surface burning characteristics <br /> Opening Notice about approvals (ASTM E 84 -96) <br /> 1. Clean the opening. Surfaces to which FS -ONE will be • Check that the penetration has been sealed according to Flame Spread: 0 <br /> applied should be cleaned of loose debris, dirt, oil, the specified drawing in the UL Fire Resistance Directory Smoke Development: 5 <br /> moisture, frost and wax. Structures supporting or Hilti Firestop Manual. For further advice, please Sound transmission dassification <br /> penetrating items must be installed in compliance with contact Hilti customer service. Refer to Hilti product (ASTM E 90 56 <br /> local building and electrical standards. literature and UL fire resistance directory for specific <br /> application details. is <br /> Application of firestop sealant IICCBO Approvals Conference of <br /> 2. Install the prescribed backfilling material type and depth Not for use... Building Officials) <br /> to obtain the desired rating (if required). Leave sufficient • High movement expansion joints Report No. 5071 <br /> depth for applying FS -ONE. • Underwater <br /> 3. Application of firestop sealant: Apply FS -ONE to the • On materials where oil, plasticizers or solvents may Cati No. State 485- Fire Marshal <br /> bleed i.e. impregnated wood, oil based seals, green or City Listing No. 4485 -1200:108 <br /> required depth in order to obtain the desired fire rating. Pfe9 � City y of New York <br /> Make sure FS -ONE contacts all surfaces to provide partially vulcanized rubber MEA 326-96-M <br /> maximum adhesion. For application of FS -ONE use a • In any penetration other than those specifically <br /> standard caulking gun, foil pack gun, bulk loader and described in this manual or the test reports ,„ <br /> bulk gun. With FS -ONE buckets, Graco type sealant safety s Tested in accordance with <br /> pumps may be used. (Contact pump manufacturer for • tlon • UL 1479 ' ^ <br /> proper selection). •Before handling, handandling, read the product and Material Safety <br /> Data Sheet for detailed use and health information • ASTM E 814 <br /> 4. Smoothing of firestop sealant: To complete the seal, tool • Keep out of reach of children • ASTM E 84 <br /> immediately to give a smooth appearance. Excess • Wear suitable gloves and eye protection <br /> sealant, prior to curing, can be cleaned away from Storage Internationally tested and approved <br /> adjacent surfaces and tools with water. • Store only in the original packaging in a location oJ .ss, gp F LUO ORlAVITY►WE(C I <br /> 5. Leave completed seal undisturbed for 48 hours. protected from moisture at temperatures between rorzusE xwnxmu�l aee�� <br /> 6. For maintenance reasons, a penetration seal could be 40 °F (5 °C) and 86 °F (30 °C) CL SEE � FIRE RESISTANCE US WC DIRECTORY <br /> permanently marked with an identification plate. In such • Observe expiration date on the packaging <br /> a case, mark the identification plate and fasten it in a <br /> visible position next to the seal. <br /> APPROVED <br /> vi <br /> . ,��, _ <br /> ' W1I1 f , . P SYST /M COMMTIKI 1 _ _._ , <br /> Lr <br /> 1. clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS -ONE. S. Leave ca► 6. Fasten identifi- <br /> wool. (If required) seal undtshr6ed for cation plate (if T i <br /> 48 hoes. required). © latest product information : <br /> www.us.hilti.com <br /> ...., <br /> I E © ordering information see page: <br /> 34 , <br /> 1. Clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS-ONE. S. Leave 6. Fasten iderxifica- <br /> wool. (If required) seal undisturbed ar tan plate (if <br /> Saving Lives through innovation & education I Hilti Firestop Guide' i • - 2006 1 1'x!79 -8000 1 www.us.hilti.com MIIL.•l " 17 <br />