10-10030 - Laserfiche WebLink

Browse Search

dn- 6998:a NP- A100(A) N OTI F 1 E R ® Addressable Multi Sensor Detector For the FireWarden Series by Honeywell Addressable Devices General The NP- A100(A) detector is an intelligent, addressable, multi- r f sensing, low- profile detector designed for use with FireWarden Series Fire Alarm Control Panels. �„ The NP- A100(A) detector uses a combination of photoelectric and thermal sensing technologies to increase immunity to alarms. Unlike traditional intelligent detectors this multi - sense detector has a microprocessor in the detector head that i " Jr processes alarm data. As a result, the detector adjusts its sen- sitivity automatically, without operator intervention or control panel programming. Areas where the NP- A100(A) detector is especially useful NP -A100 with B710LP base include office complexes, schools, college campuses, manu- facturing and industrial facilities, and anywhere else the use of a particular area may change. The NP- A100(A) automatically adjusts its sensitivity to the environment. Relative humidity: 10% — 93% noncondensing. Features Thermal sensing rating: fixed - temperature setpoint 135 °F SLC loop: (57 °C). • Two wire loop connection. ELECTRICAL SPECIFICATIONS: • Unit uses base for wiring. Voltage range: 15 — 32 volts DC peak. Addressing: Standby current (max. avg.): 360 pA. • Addressable communication. Loop resistance: 40 ohms maximum. Refer to panel installa- • Direct -Dial entry of address: 01 -99 with FireWarden -100 -2 tion manuals. and 01 -50 with FireWarden -50. LED current (max.): 6.5 mA @ 24 VDC ( "ON "). • Addresses can be viewed and changed without electronic programmers. Installation Architecture: The NP- A100(A) plug -in detector uses a separate base to sim- • Automatically adjusts sensitivity levels without operator plify installation, service, and maintenance. A special tool intervention or programming. Sensitivity increases with allows maintenance personnel to plug -in and remove detec- heat. tors without using a ladder. Mount base on an electrical back- • Microprocessor- based, combination photo and thermal box at least 1.5" (3.81 cm) deep. Suitable mounting base technology. boxes include: • • Dual bi -color LED design provides 360° viewing angle 4.0" (10.16 cm) square box. • Built -in tamper- resistant feature. • 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box. • Several base options, including relay, isolator and sounder. • Single -gang box (except relay or isolator base). Operation: APPLICATION NOTE: The NP- A100(A) detector has the unique ability to adjust sensitivity according to the environment, based on • LED's lock red when in alarm. heat and smoke levels. Avoid installing these detectors in locations • Built - in functional test switch activated by external magnet. that are susceptible to rapid and high temperature changes. An Mechanica/s: example of an incorrect application would be near or in line with the output of a self - contained heater. • SEMS screws for wiring of the separate base. Other system features: Agency Listings and Approvals • Listed to UL 268 These listings and approvals apply to the modules specified in this. In some cases, certain modules or applications may not Specifications be listed by certain approval agencies, or listing may be in pro - Size: 2.0" (5.3 cm) high x 4.1" (10.4 cm) diameter installed in cess. Consult factory for latest listing status. B501 base, 6.1" (15.5 cm) diameter installed in B710LP base. • UL Listed: S1115 • Shipping weight: 5.2 oz. (147 g). CSFM: 7272-0028:258 Operating temperature: 0 °C to 38 °C (32 °F to 100 °F). Product Line Information Operating altitude: up to 10,000 feet. NP- A100(A): Low - profile, intelligent multi- sensor detector. UL- Listed velocity range: 0 — 4000 ft. /min. (1219.2 m/min.), B710LP(A) base included. suitable for installation in ducts. dn- 6998:a • 07/31/09 — Page 1 of 2