Laserfiche WebLink
L aiumiaimi i <br /> rf aoci if (ori <br /> FS -ONE Product description FS -ONE <br /> • Intumescent (expands when exposed to fire) firestop sealant <br /> High Performance that helps protect combustible and non - combustible penetra- Technical Data <br /> 9 lions for up to 4 hours fire rating <br /> Intumescent Firestop t 73 °F (23 °C) and 50% relative humidity <br /> P Product features Chemical basis <br /> Sealant • Smoke, gas and water resistant after material has cured Water -based intumescent acrylic dispersion <br /> • Contains no halogen, solvents or asbestos why <br /> • H igh fire rating properties Approx. 1.5 q/cm' <br /> v _ Color <br /> Nz Water based, easy to clean Red <br /> ,,,+) " Areas of application Working time <br /> : ` . • Steel, copper and EMT pipes Approx. 20 -30 min. <br /> • Insulated steel and copper pipes Curing time <br /> I `• ,�,., • Cable bundles Approx. 4 mm / 3 days <br /> .. ii. ,.,_ ! :. • Closed or vented plastic pipes Shore A Hardness - <br /> System Ad vantage tcustomer Benefits • HVAC penetrations Approx. 35 <br /> • Protects most rypical For use with Movement capability <br /> penetration a (cations • Concrete, masonry, drywall and wood floor assemblies Approx. 5% <br /> • Easy to work with and fast cleanup • Wall and floor assemblies rated up to 4 hours Intumescent Activation <br /> • Can be painted Approx 482 °F (250 ° C) <br /> • Single component systems available Examples Expansion rate (unrestricted): <br /> • Sealing around plastic pipe penetrations in fire rated Up to 3 -5 times original volume <br /> • Meets I EEDTM rreegqdrerrrents for indoor <br /> envir nrr r tab qual credit 41 IrOw construction Temperature resistance (cured) <br /> B • Sealing around combustible and non - combustible —40 °F to 212 °F ( -40 °C to 100 °C) <br /> laf>d r penetrations in fire rated construction Application temperature <br /> Atlh�ives and 4.2 Pairtts and Cottings; Pe � � <br /> 41°F to 104 °F (5 °C to 40 °C) <br /> Installation instructions for FS -ONE Surface twining characteristics <br /> Opening Notice about approvals (ASTM E -96) <br /> 1. Clean the opening. Surfaces to which FS -ONE will be • Check that the penetration has been sealed according to Flame Spread: 0 <br /> applied should be cleaned of loose debris, dirt, oil, the specified drawing in the UL Fire Resistance Directory Smoke Development: 5 <br /> moisture, frost and wax. Structures supporting or Hilti Firestop Manual. For further advice, please Sound transmission classification <br /> penetrating items must be installed in compliance with contact Hilti customer service. Refer to Hilti product (ASTM E 90 -99) 56 <br /> local building and electrical standards. literature and UL fire resistance directory for specific <br /> application details. Approvals <br /> Application of firestop sealant ICBO (International Conference of <br /> 2. Install the prescribed backfilling material type and depth Not for use... Building Officials) <br /> to obtain the desired rating (if required). Leave sufficient • High movement expansion joints Report No 5071 <br /> depth for applying FS -ONE. • Underwater California State Fire Marshal <br /> 3. Application of firestop sealant: Apply FS -ONE to the • On materials where al, plasticizers or solvents may Listing No. 4485 - 1200:108 <br /> required depth in order to obtain the desired fire rating. bleed i.e. impregnated wood, oil based seals, green or <br /> eq p g City of New York <br /> Make sure FS -ONE contacts all surfaces to provide partially vulcanized rubber MEA 326 -96 -M <br /> maximum adhesion. For application of FS -ONE use a • In any penetration other than those specifically <br /> standard caulking gun, foil pack gun, bulk loader and described in this manual or the test reports <br /> bulk gun. With FS -ONE buckets, Graco type sealant Safety precautions Tested in accordance with <br /> pumps may be used. (Contact pump manufacturer for • Before ha ndling, read the product and Material Safety • UL 1479 <br /> proper selection). Data Sheet for detailed use and health information • ASTM E 814 <br /> 4. Smoothing of firestop sealant: To complete the seal, tool • Keep out of reach of children • ASTM E 84 - <br /> immediately to give a smooth appearance. Excess • Wear suitable gloves and eye protection <br /> sealant, prior to curing, can be cleaned away from Storage Internationally tested and approved <br /> adjacent surfaces and tools with water. • Store only in the original packaging in a location „.ss�,, RLL OR Voo CANTY AMTERNL <br /> 5. Leave completed seal undisturbed for 48 hours. protected from moisture at temperatures between ` ° f0R1 r STaPsnTE,ns <br /> 6. For maintenance reasons, a penetration seal could be 40 °F (5 °C) and 86 °F (30 °C) c • US SEE UL FIRE RESISTANCE °RECTORY <br /> ' <br /> permanently marked with an identification plate. In such • Observe expiration date on the packaging <br /> a case, mark the identification plate and fasten k in a .' <br /> visible position next to the seal. <br /> APPROVED <br /> lo : ,;;:!7:4w-, � �° APPROVED <br /> AUMtAfllIL! <br /> L . 1. Clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS -ONE. 5. Leave a Fasten identdi- <br /> 1H, wool. (If required) seal undrstturbed or 6. cation plate (if <br /> 48 hors, required). © latest product information : <br /> wwvv.us.hilti.com ww.us.hilti.com <br /> [ El E„,„_,, F ,H © ordering information see page: 34 <br /> 1. Clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS -ONE. 5. Leah° ed 6. Fasten identifiica- <br /> wool pf required) seal undisturbed lion plate (if <br /> Saving Lives through innovation & education 1 Hilti Firestop Guide/0-2006 I 1 79 -8000 1 www.us.hilti.com =al 17 <br />