10-10689 - Laserfiche WebLink

Browse Search

MIL:TT Product Information FS -ONE Product description FS -ONE • Intumescent (expands when exposed to fire) firestop sealant High performance that helps protect combustible and non - combustible penetra- Technical Data tions for up to 4 hours fire rating At 73 °F (23 °C) and 50 0 /0 relative humidity Intumescent Firestop features Chemical basis Sealant • Smoke, gas and water resistant after material has cured Water -based intumescent acrylic dispersion • Contains no halogen, solvents or asbestos Density • High fire rating properties Approx. 1.5 q /cm • Water based, easy to clean Color Red , ' Areas of application Working time • Steel, copper and EMT pipes Approx. 20-30 min. i` • Insulated steel and copper pipes Curing time Cable bundles r .- -- • Closed or vented plastic pipes Shore A Ha do ss System Advantage / Customer Benefits • HVAC penetrations Approx. 35 • Protects most typical firestop For use with Movement capability penetration applications • Concrete, masonry, drywall and wood floor assemblies Approx. 5% • Easy to work with and fast cleanup • Wall and floor assemblies rated up to 4 hours Intumescent Activation • Can be painted Approx 482 °F (250 °C) • Single component systems available Examples Expansion rate (unrestricted): • Meets LEEDTM requirements for indoor • Sealing around plastic pipe penetrations in fire rated Up to 3 -5 times original volume environmental quality credit 4.1 Low construction Temperature resistance (cured) Emitting Materials, Sealants and Sealing around combustible and non - combustible —40 °F to 212 °F ( -40 °C to 100 °C) n • Sli Adhesives and 4.2 Paints and Coatings penetrations in fire rated construction Application temperature 41°F to 104 °F (5 °C to 40 °C) F) Installation instructions for FS -ONE Surface buming characteristics n Opening Notice about approvals (ASTM E 84 -96) z 1. Clean the opening. Surfaces to which FS -ONE will be • Check that the penetration has been sealed according to Flame Spread: 0 N applied should be cleaned of loose debris, dirt, oil, the specified drawing in the UL Fire Resistance Directory Smoke Development: 5 moisture, frost and wax. Structures supporting or Hilti Firestop Manual. For further advice, please Sound transmission classification o penetrating items must be installed in compliance with contact Hilti customer service. Refer to Hilti product (ASTM E 90 -99) 56 local building and electrical standards. literature and UL fire resistance directory for specific F application details. Approvals I-4i- Application of firestop sealant ICBO (International Conference of 2. Install the prescribed backfilling material type and depth Not for use... Building Officials) to obtain the desired rating (if required). Leave sufficient • High movement expansion joints Report No. 5071 depth for applying FS -ONE. • Underwater California State Fire Marshal 3. Application of firestop sealant: Apply FS -ONE to the • On materials where oil, plasticizers or solvents may Listing No. 4485 - 1200:108 required depth in order to obtain the desired fire rating. bleed i.e. impregnated wood, oil based seals, green or City of New York Make sure FS -ONE contacts all surfaces to provide partially vulcanized rubber MEA 326-96-M maximum adhesion. For application of FS -ONE use a • In any penetration other than those specifically standard caulking gun, foil pack gun, bulk loader and described in this manual or the test reports bulk gun. With FS -ONE buckets, Graco type sealant Safety precautions Tested in accordance with pumps may be used. (Contact pump manufacturer for • Before handling, read the product and Material Safety • UL 1479 proper selection). Data Sheet for detailed use and health information • ASTM E 814 4. Smoothing of firestop sealant: To complete the seal, tool • Keep out of reach of children • ASTM E 84 immediately to give a smooth appearance. Excess • Wear suitable gloves and eye protection sealant, prior to curing, can be cleaned away from Stora a Intemationally tested and approved adjacent surfaces and tools with water. 9 • Store only in the original packaging in a location ss,p, FILL, VOID OR CAVITY MATERIAL 5. Leave completed seal undisturbed for 48 hours. protected from moisture at temperatures between ° R FOR USE IN THROUGH - PENETRATION 6. For maintenance reasons, a penetration seal could be 40 °F (5 °C) and 86 °F (30°C) C ® US RRESTOE DI P ( ) SEE UL RRE RESISTANCE KiECTORY permanently marked with an identification plate. In such • Observe expiration date on the packaging 66Y7 a case, mark the identification plate and fasten it in a visible position next to the seal. i r ow" - A Ale ...A ' , -..' 7 , APPROVED ' `, ;.� - -. � S YSTEM COMPATIBLE 1. Clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS -ONE. 5. Leave completed 6. Fasten identifi- wool. (If required) seal undisturbed for cation plate (if 48 hours. required). latest product information : .. www.us.hilti.com „, 0 „:„ ... - Fi d ordering information see page. .., _. ___ 1. Clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS -ONE. 5. Leave completed 6. Fasten identifica- wool. (If required) seal undisturbed for lion plate (if Saving Lives through innovation & education Hilti Firestop Guide 1 4 079 -8000 www.us.hilti.com Mitit..T7” if < 17