|
11 Product Information
<br /> FS -ONE Product description FS -ONE
<br /> • Intumescent (expands when exposed to fire) Firestop sealant
<br /> High Performance that helps protect combustible and non - combustible penetra- Technical Data
<br /> tions for up to 4 hours fire rating
<br /> Intumescent Firestop At 73 °F (23 °C) and 50% relative humidity
<br /> Sealant Product features Chemical basis • Smoke, gas and water resistant after material has cured Water -based intumescent acrylic dispersion
<br /> • Contains no halogen, solvents or asbestos Density
<br /> • High fire rating properties Approx. 1.5 g /cm'
<br /> • Water based, easy to clean Color
<br /> ` r.:'' Areas of application Red
<br /> g
<br /> workin time
<br /> . • Steel, copper and EMT pipes Approx. 20 -30 min. _
<br /> • Insulated steel and copper pipes Curing time i_;
<br /> ,*� • Cable bundles Approx. 4 mm / 3 days
<br /> • Closed or vented plastic pipes Shore A Hardness C
<br /> q" a . I` '- • HVAC penetrations
<br /> � F � Approx. 35
<br /> • T °. " '4,'', Ip' For use with Movement capability
<br /> ' I Itw • Concrete, masonry, drywall and wood floor assemblies Approx. 5%
<br /> �
<br /> ▪ , : y � �a � _ • Wall and floor assemblies rated up to 4 hours Intumescent Activation
<br /> ,,".4'1,',:':-:....i:_._ ' ` �� , �� w . Approx 482 °F (250 °C)
<br /> '41 ' �s � - Examples Expansion rate (unrestricted):
<br /> • Sealing around plastic pipe penetrations in fire rated Up to 3 -5 times original volume
<br /> ' " sip : ' ` F ° ' P construction
<br /> 1. cry T . . . , . Temperature resistance (cured)
<br /> „ , , . t • Sealing around combustible and non- combustible —40 °F to 212 °F ( -40 °C to 100 °C)
<br /> ® ,1 , 4.2 Pa nts � penetrations in fire rated construction Application temperature 7)
<br /> 41 °F to 104 °F (5 °C to 40 °C) F,
<br /> Installation instructions for FS -ONE Surface burning characteristics n
<br /> Opening Notice about approvals (ASTM E 84-96) z
<br /> 1. Clean the opening. Surfaces to which FS -ONE will be • Check that the penetration has been sealed according to Flame Spread: 0 N
<br /> applied should be cleaned of loose debris, dirt, oil, the specified drawing in the UL Fire Resistance Directory Smoke Development: 5
<br /> moisture, frost and wax. Structures supporting or Hilti Firestop Manual. For further advice, please Sound transmission classification o
<br /> penetrating items must be installed in compliance with contact Hilti customer service. Refer to Hilti product (ASTM E 90 -99) 56 0
<br /> local building and electrical standards. literature and UL fire resistance directory for specific
<br /> application details. Approvals (. Application of Firestop sealant ICBO (International Conference of
<br /> 2. Install the prescribed backfilling material type and depth Not for use... Building Officials)
<br /> to obtain the desired rating (if required). Leave sufficient • High movement expansion joints Report No. 5071
<br /> depth for applying FS -ONE. • Underwater
<br /> 3. Application of Firestop sealant: Apply FS -ONE to the • On materials where oil, plasticizers or solvents may Listing g N i Calif . 44 Fire Marshal
<br /> required depth in order to obtain the desired fire rating. bleed i.e. impregnated wood, oil based seals, green or No. 4485 5 1200:108
<br /> Make sure FS -ONE contacts all surfaces to provide partially vulcanized rubber City of New York
<br /> maximum adhesion. For application of FS -ONE use a • In any penetration other than those specifically MEA 326-96-M
<br /> standard caulking gun, foil pack gun, bulk loader and described in this manual or the test reports
<br /> bulk gun. With FS -ONE buckets, Graco type sealant Tested in accordance with
<br /> pumps s ma be used. (Contact pump manufacturer for Safety precautions
<br /> may p p manuacturer • Before handling, read the product and Material Safety • UL 1479
<br /> proper selection). Data Sheet for detailed use and health information • ASTM E 814 m
<br /> 4. Smoothing of firestop sealant: To complete the seal, tool • Keep out of reach of children • ASTM E 84
<br /> immediately to give a smooth appearance. Excess • Wear suitable gloves and eye protection
<br /> sealant, prior to curing, can be cleaned away from Internationally tested and approved
<br /> adjacent surfaces and tools with water. Storage
<br /> • Store only in the original packaging in a location aS,F FILL, VOID OR CAVITY MATERIAI
<br /> 5. Leave completed seal undisturbed for 48 hours. protected from moisture at temperatures between ° 'p FOR USE IN THROUGH - PENETRATION
<br /> 6. For maintenance reasons, a penetration seal could be 40`F (5 °C) and 86 °F ( 30 °C ) `J C t I )US FIRESTOP SYSTEMS
<br /> p SEE UL FIRE RESISTANCE DIRECTORY
<br /> permanently marked with an identification plate. In such • Observe expiration date on the packaging 66Y7
<br /> a case, mark the identification plate and fasten it in a
<br /> visible position next to the seal.
<br /> ill ! 2,";.../.,1 '''' ..,,,--" APPROVED 7 ti
<br /> i . ,,-
<br /> SYSTEM rowans«
<br /> _
<br /> 1. Clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS -ONE. 5. Leave completed 6. Fasten identifi-
<br /> wool. If required) seal undisturbed for cation plate Of
<br /> 48 hours. requtredJ. m
<br /> latest product information :
<br /> www.us.htlti.com o
<br /> __,
<br /> ..,
<br /> " E � ' © ordering information see page:
<br /> 34
<br /> 1. Clean opening. 2. Pack mineral 3. Apply FS -ONE. 4. Smooth FS -ONE. 5. Leave completed 6. Fasten identifica-
<br /> wool. (If required) seal undisturbed for tion plate (if
<br /> Saving Lives through innovation & education I Hilti Firestop Guidel =2006 I 1-W179-8000 1 www.us.hilti.com Owila ; 17
<br />
|