Laserfiche WebLink
ADHESIVE <br /> FTR 19oe <br /> Product Data <br /> FUR 1.9oe is a low VOC solvent borne contact adhesive, designed for bonding non -fleece back FiberTite <br /> membranes to pre - approved horizontal and vertical surfaces. <br /> DESCRIPTION PHYSICAL PROPERTIES <br /> ,•r �` a rte' 'R • , - +ts <br /> FTR 190e is compliant with all air quality districts in the state ^ °° <br /> of California and other regulated areas in the USA, making it miry 1sotxr 24eps <br /> the most environmentally friendly "solvent" bome adhesive h,, °r f <br /> `Ep% <br /> available. <br /> Y29i <br /> Coverage 5©:friig , € .P1,11. bol <br /> FTR 190e is a Nitrile/PVC polymeric adhesive. The adhesive w ` " � " issglL <br /> is quick drying but has an extended "open- time" so proper Application <br /> planning, placement and care to insure appropriate adhesion e�,sh,rdrerers(xay. ' R- <br /> especially during periods of high humidity, is necessary. '.� �s -� � r.>u . . _�` r��,� 1g or> <br /> Shelf Life <br /> FTR 190e is listed/approved for use with specific FiberTite ` c <br /> Roofing Systems by FM- Global and Underwriters Laboratories. x # w , <br /> Wt. Gal. 7 S-(6 t ligeN iitshippealna gal <br /> parts <br /> A P P L I C A T I O N ) 40° eod,�aingup tce€r°r <br /> See Seaman Corporation Guide Specification (GS 04/08) and <br /> Addendums as well as Seaman Corporation/FiberTite Material <br /> Safety Data Sheets (MSDS) for additional and specific application, <br /> design parameters and material precautions. <br /> Surfaces/substrate must be clean, dry and free of dirt, oil, grease <br /> or similar contaminates that could interfere with the bonding <br /> process. <br /> Compatible substrates include: masonry, wood and metal for <br /> flashing applications as well as pre - approved polyisocyanurate <br /> insulation, approved gypsum based cover -boards and approved <br /> base sheets for horizontal roofing applications. <br /> FTR 190e can be applied by either rolling or spraying at a <br /> coverage of approximately 50 ft net per gallon (1.2 m liter), <br /> 45 ft per 1/2 gallon to the substrate (1.1 m 1/2 liter), 55 ft per <br /> 1/2 gallon (1.3 m liter) to the membrane. Actual coverage <br /> depends upon the porosity and smoothness of the surface to <br /> be bonded. For more Information on FlberTka Systems <br /> , • and accessories please can: <br /> j <br /> • L Seaman Corporation (800) 927 -8578 <br /> To ensure proper application and curing of the adhesive, the -M1° htemat�m� ta Zsx- " <br /> www <br /> outside air temperature must be 40° F (4.4 °C) and rising. INTELLIGENT <br /> Spray or roll a smooth, even coat of adhesive over the exposed, ROORric SOLUTIONS Flbeente is a registered trademark of Seaman Corporation. <br /> pre - positioned bottom of the FberTRe membrane and a mirrored <br /> FLU <br /> symmetrical area of the substrate, insuring 100% coverage. -41> Si°i'°"o the conditions of Approval for ° et CFFA `a <br /> roof oararina w (maw as desalted C <br /> Allow the solvents in the adhesive to dissipate to the point aff intheaeremeWionoft aApproval ckra. ^ AEEOCIATION. INC. <br /> Nrtf <br /> that the adhesive is "sticky" but not stringy to the touch. When As to an Wane! we espouse 0 .44 See UL sufficiently cured/dry, carefully maneuver the glued portion of >J ,E and UL ce :led <br /> the FiberTite membrane onto the glued substrate. of. ,a a Wa a. <br />