11-11786 - Laserfiche WebLink

Browse Search

- -►NP-100(A), NP-100T(A) dn-6995:b•Ai-320 NP -1 OOR(A) N OT 1 F' 1 E R� Addressable Photoelectric Detectors �� for the FireWarden Series by Honeywefl General �� _ The NP-100 and NP-100T addressable, low-profile plug-in �: ;��,��f'�: ^�,,� photoelectric detectors use a state-of-the-art photoelectric ` �•� sensing chamber with communications to provide open area . F protection and are used exclusively with NOTIFIER's FireWar- _ ,„� den Series (FireWarden-100-2 and FireWarden-50) Address- - able Fire Alarm Control Panels (FACPs). The NP-100T adds �� " �� thermal sensors that wili alarm at a fixed temperature of 135°F (57°C). Since these detectors are addressable, they will help emergency personne� quickly locate a fire during its early stages, potentiaily saving precious rescue time while also reducing property damage. Two LEDs on each sensor light to NP with B710LP base provide a local, visible sensor indication. Remote LED annun- ciator capability is available as an optional accessory (P/N RA100Z(A)) The NP-100R is a remote test capable detector for use with DNR(W) duct smoke detector housings. Features SLC loop: • Two-wire loop connection. �. ,� � � • Unit uses base for wiring. Addressing: • Addressable by device. • Direct Decade entry of address: 01 - 99 with FireWarden- 100-2, and 01 - 50 with FireWarden-50 Archltecture: NP-100T wtth B710LP base • Unique single-source, dual-chamber design to respond quickly and dependably to a broad range of fires. • Sleek, low-profile design. APpI1Cat1011S • Integral communications and built-in type identification. Use photoelectric detectors in life-safety applications to pro- • Built-in tamper-resistant feature. vide a broad range of fire-sensing capabiiity, especially where • Removable cover and insect-resistant screen for simple smoldering fires are anticipated. lonization detectors are often field cleaning. better than photoelectric detectors at sensing fast, flaming Operatlon: fires. • Withstands air velocities up to 4,000 feet-per-minute (20 m/ Construction sec.) without triggering a false alarm. These detectors are constructed of off-white LEXAN�. • Factory preset at 1.5% nominal sensitiviry for panel alarm NP-100(T) plug-in, low-profile smoke detectors are designed threshold level. to commercial standards and offer an attractive appearance. • Visible LED "blinks" when the unit is addressed (communi- cating with the fire panel) and latches on in alarm. I nstallation Mechanicals: NP-100(T) plug-in detectors use a detachable mounting base • Sealed against back pressure. to simpiify installation, service and maintenance. Mount base • Direct surface mounting or electrical box mounting. on box which is at least 1.5 inches (3.81 cm) deep. Suitable • Mounts to: single-gang box, 3.5" (8.89 cm) or 4.0" (10.16 boxes include: cm) octagonai box, or 4 0" (10.16 cm) square electrical box • 4.0' (10.16 cm) square box with plaster ring. (using a plaster ring — included). • 4.0' (10.16 cm) octagonal box. Other system features: • 3.5' (8.89 cm) octagonal box. • Fully coated circuit boards and superior RF/transient pro- . Single-gang box. tection. NOTE: Because of the inherent supervision provided by the SLC • 94-VO plastic flammabiliry rating. loop, end-of-l/ne res/stors are not required. �ring "T-taps° or • Low standby current. branches are permitted for Style 4 (C/ass 8) wiring. NP-100R Optlons: mounts in a DNR(VV) duct detector housing. • Remote LED output connection (P/N RA100Z). dn-6995:b • 3J12/10 — Page 1 of 2 P.7