Laserfiche WebLink
NOTE: Wiring Diagrams this Page: NZM-100 and NC-100R <br /> • Connect modules to listed compatible control panels only. • Detectors must be UL listed compatible with module. <br /> • Terminal wiring must be power limited. • Install detectors per manufacturers' installation instructions. <br /> • DO NOT MIX fire alarm initiating, supervisory, and secu- • Power to the interface module must be externally <br /> riry devices on the same circuit. switched to reset the detectors. An relay control module <br /> • DO NOT LOOP wire under terminals. Break wire run to can be used to switch power from a standard power sup- <br /> provide supervision of connections. ply; see Figure 8 below. <br /> Figure 6 NZM-100: Intertace two-wire conventfonai detectors, NFPA Style B. <br /> 70 Next (—) FROM Panel <br /> Device �+) �+� orPrevious <br /> INTERFACE Device <br /> ^ MODULE � �� Communication Une <br /> � ° 32 VDC maximum. <br /> 9 F3 � Twisted-pair is <br /> e � � _ recommended. <br /> + <br /> 3.9K EOL �*� 2 �_� Listed Battery Backup <br /> Resistor 6 11A 3 switched DC <br /> (inGuded) 5 � 4 � + power supply. <br /> A2143-10 �� ��ss <br /> + � � � � O � Optional B�anch Circuit <br /> TO NeM Inte�face Module <br /> Module supervises supply <br /> voltage and detector loop. s�zow�rs.wmi <br /> Figure 7 NZM-100: Interface two-wlre conventional detectors, NFPA Style D. <br /> TO Next — FROM Panel <br /> Device (+ (+) o� Previous <br /> INTERFACE Device <br /> � MODULE � �� Communication Line <br /> , 32 VDC maximum. <br /> Twisted-pair is <br /> g 0 p recommended. <br /> 8 � � + <br /> � " 2 �–) Usted Batte Backup <br /> 5 \yv q + switched DC <br /> �� �s �� power supply. <br /> Q O � O Q .� Optional 8ranch Circuit <br /> TO NeM lnteAace Module <br /> Module supervises supply <br /> voltage and detector loop. �pw���wmr <br /> Figure 8 Applications with Conventional Detectors: Resetting detectors <br /> NOTE: To reset conventiona! detectors, exiernally switch o/f power to the interface modu/e they are connected to. This example shows NC-f00R <br /> (see separate data sheet). <br /> TO Next (+ �� — FROM Pane! <br /> Devrce (+) orPrevious <br /> RELAY Device <br /> DC POWER CONTROL <br /> SUPPLY �+> � MODULE C\ R <br /> o v � <br /> Listed forFire (—) 9 � 0 Communication Line <br /> Piotection with 32 VDC maximum. <br /> Baitery Backup e � — Twisted-pair is <br /> 7'� 2 + recommended. <br /> (—� 6� 3 <br /> (+� 5 �[°'I f' 4 <br /> LOpP ADDRESS <br /> Q � � � � <br /> 8720wir7.wmf <br /> Notifier� and FireWarden� are registered trademarks of Honeywell <br /> International Inc. <br /> �2008 by Honeywell International Inc. All rights reserved. Unauthorized use <br /> oi this document is strictly prohibited. <br /> I�O 900 This document is not intended to be used for installation purposes. <br /> We try to keep our product information up-to-date and accurate. <br /> We cannot cover all specific applications or anticipate all requirements. <br /> gr��� �� All specifications are subject to change without notice. <br /> QUALIT� SYSTEMS MadeintheU.S.A. <br /> For more information, contact Notiffer. Phone: (203) 484-7161, FAX: (203) 484-7118. <br /> www.notifier.com <br /> Page 6 of 6— dn-6999:a • 04/28l08 <br /> P.14 <br />