11-11786 - Laserfiche WebLink

Browse Search

SpectrAlert Advance Speci�cations Generat SpectrAlert Advance horns, strobes and homhtrobes shall mount to a standard 4 x 4 x Ph-mch back box, 4-inch octagon back box or double-gang back box.Two-wire products shall also mount to a single-gang 2 x 4 x 1'/e-inch back box. A universal mounting plate shall be used for mounting ceiling and wali products.The notification apphance circuit winng shall terminate at the urnversai mounting p�ate. Also, SpectrAlert Advance products, when used with the Syno-Grcuit" Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the SynoCirc�it Module, 12-volt rated notification apphance circwt outputs shall operate between nine and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 17 and 33 volts. indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC, or full-wave rectified, unfiltered power supply Strobes and horn/strobes shali have field-selectable candela settings induding 15,15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service.The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shail consist of a xenon flash tube and associated lens/reflector system. Horn/Strobe Combination The horn/strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horMstrobe shall be wired as a primary-signaling notification appliance and comply with the Americans wirh Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shail consist of a xenon flash tube and associated lens/reflector system.The horn shail have three audibility options and an option to switch between a temporal three-pattem and a non-temporal (continuous) pattern.These options are set by a multiple position switch.On four-wire products, the strobe shall be powered independently of the sounder.The horn on horn/strobe models shall operate on a coded or non-coded power supply. putdoor Products Spe�trAlert Advance outdoor horns, strobes and horn/strobes shall be listed for outdoor use by UL and shall operate between minus 40 degrees and 151 degrees Fahrenheit.The products shall be listed for use with a System Sensor outdoor/weatherproof back box with half inch and three-fourths inch conduit entries. Synchronization Moduie The module shall be a System Sensor Sync�Circuit model MDL listed to UL 464 and shall be approved for fire protective service.The module shail synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn/strobe models over a single pair of wires. The module shall mo�nt to a 4��/,s x 4�Y,s x 2'/s-inch back box.The module shall a�so control two Style Y(class B) circuits or one Style Z (class A) circuit.The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they controi.The module shall not operate on a coded power supply. Standard Operating Temperature 32°F to 120°F (0°C to 49 K Series Operating Temperature —40°F to 151 °F (-40°C to 66°C) Numidity Range 10 to 9346 non-condensing (indoor products) Strobe Ftash Rate 1 Flash per second Nominal Voltage Regulated 12DUFWR or regulated 24DClFWR' Operating Voltage Range 8 to 17.5 V(12V nominal) or 16 to 33 V(24 nominal) Input terminal wire gauge 12 to 18 AWG Ceiling mount dimensions {including lens} 6.8" diameter x 2.5' high (173 mm diameter x 64 mm high) Wall maunt dimensions (inctuding tens) 5.6'L x 4.7 W x 2.5"D (142 mm L x 119 mm W x 64 mm D) Horrt dimensions 5.6"L x 4.7'W x 13"D (142 mm L x 119 mm W x 33 mm D) Waii-mount batk box skirt dimensions (BBS-2, BBSW-2) 5.91 x S.OIN x 2.2� (151 mm L x 128 mm W x 56 mm D) teiling-mount back box skirt dimensions (BBSC-2, BBSCW-2► 71 "diameter x 2.25' high (1 SO mm diameter x 57 mm high) Wall-mount weatherproof back box dimensions (SA-WBB) 5.7t x 5.1 W x 2.0'D (145 mm L x 130 mm W x S1 mm D) Ceiling-mount weatherproof back box dimensions (SA-WBBCj 71"diameter x 2.0" high (180 mm diameter x 51 mm high) Wali-mount trim ring dimensions (TR-H5, TRW-ii5) 5.71 x 4.8121N x 0.35"D (146 mm L x 122 W mm x 9 D mm) Ceiling-mount trim ring dimensions (TRC-HS,TRCW-HS} 6.9'diameter x 035 high (176 mm diameter x 9 mm high) Notes: 1 Full Wave Rectified (FWR) voltage is a non-regulated, time varying power source that is used on some power supply and panel outputs. 2. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 15/75 cd. A05-0995-005 P.16