11-11869 - Laserfiche WebLink

Browse Search

• df-60379:A1 • E-400 CRF-3oo(A) � ��•�iTe�A�arms Relay Module by Honeywell -� - General The CRF-300(A) Addressable Relay Module provides the sys- tem with a dry-contact output for activating a variety of auxil- iary devices, such as fans, door holders, dampers, control equipment, etc. Addressability allows the dry contact to be activated through panel programming, on a select basis. �■ LiteSpeedT"' is a communication protocol developed by �'� Fire•Lite Engineering that greatly enhances the speed of com- """ � ��~� munication between analog intelligent devices. Intelligent ,�,,,,, .�,.,,, devices communicate in a grouped fashion. If one of the T devices within the group has new information, the panel CPU •°""_ ""�"*_ stops the group poll and concentrates on single points. The ��_ °,..: �� net effect is response speed greater than five times that of m � other designs. wa Features • Built-in type identification automatically identifies these � devices to the control panel. • Internal circuitry and relay powered directly by two-wire � SLC loop. • Integral LED "blinks" green each time a communication is CRF-300(A) received from the control panel and turns on in steady red when activated. • High noise immunity (EMF/RFI) • Wide viewing angle of LED. • SEMS screws with clamping plates for wiring ease. S pecifications • Direct-dial entry of address: 01— 159 for MS-9600(A) series Normal operating voltage: 15 to 32 VDC panels, 01 — 99 on MS-9200UDLS(A) and MS-9050UD(A). Maximum SLC current draw: 6.5 mA (LED on). Applications Average operating current: 230 NA direct poll (CLIP mode), 255 NA group poll (LiteSpeed mode) with LED flashing. The CRF-300(A) may be programmed to operate dry contacts EOL resistance: not used. for door holders, Air Handling Unit shutdown, etc., and to reset four-wire smoke detector power Temperature range: 32°F to 120°F (0°C to 49°C) Humidity range: 10% to 93% non-condensing. Construction Dimensions: 4.5" (11 43 cm) high x 4" (10.16 cm) wide x • The face plate is made of off-white heat-resistant plastic. 1.25" (3.175 cm) deep. Mounts to a 4" (10 i6 cm) square x • Controls include two rotary switches for direct-dial entry of 2•125" (5.398 mm) deep box. address setting. • The CRF-300(A) is configured for a single Class B(Style Y) Relay Contact Ratings or Class A(Style Z) Notification Appliance Circuit. Maximum Current • The CRF-300(A) provides two Form-C dry contacts that Load Description Application Voltage Rating switch together Resistive Non-Coded 30 VDC 3.0 A Operation Resistive Coded 30 VDC 2.0 A Each CRF-300(A) uses one of the addresses on a SLC loop. It Resistive Non-Coded 110 VDC 0.9 A responds to regular polls from the control panel and reports its Resistive Non-Coded 125 VAC 0.9 A type and status, including the open/normal/short status of its Notification Appliance Circuit (NAC) The LED blinks with each Inductive (UR=Sms) Coded 30 VDC 0.5 A poll received. On command, it activates its internal relay. Inductive (L/R=2ms) Coded 30 VDC 1.0 A NOTE: Open/short supervrsion rs suspended with the CRF-300. Inductive (PF=0.35) Non-Coded 125 VAC 0.5 A Rotary switches set a unique address for each module. The address may be set before or after mounting. The built-in TYPE CODE (not settable) will identify the module to the con- trol panel, so as to differentiate between a control module and a relay module. df-60379:A1 • OS/04/09 — Page 1 of 2