Laserfiche WebLink
SECTION i!I—SYSTEM COMPONFNTS <br /> UL EX. 5174 10-31-97 Page 3-4 <br /> CONDUIT OFFSET ASSEMBLY "COMPRESSION-SEAL"ADAPTOR <br /> The Conduit Offset Assembly is used to change direction of the This adaptor is a mechanical bulkhead fitting that produces a <br /> wire rope on detection,mechanical gas valve, and remote pull sta- liquid-tight seal around pipe and conduit when installing distribu- <br /> tion lines. The conduit offset assembly can only be used in the tion piping and detection conduit through restaurant hoods and <br /> area where the conduit attaches to the regulated release assem- ducts. The "Compression-Seal" adaptor is a straight-through <br /> bly When using the conduit offset assembly, the maximum num- design requiring no cutting or threading of conduit or pipe The <br /> ber of pulley elbows is still allowed The Conduit Offset Shipping adaptor is available for pipe sizes of 1/4 in. (Part No 79148), 3/8 <br /> Assembly, Part No 79825, consists of 6 conduit offsets. in. (Part No 79150), 1/2 in. (Part No 79146), and EMT conduit <br /> size of 1/2 in (Part No.79152) Each"Compression-Seal"adaptor <br /> �_CONDUIT shipping assembly must be ordered as stated below <br /> COUPLING <br /> Shipping <br /> Assembly Hole Size <br /> Size Part No. Qty_. Rec�uired <br /> CONDUIT 1/4 in. Pipe 79149 24 3/4 in. <br /> OFFSET 3/8 in. Pipe 79151 24 1 1/8 in. <br /> 1/2 in. Pipe 79147 24 1 1/8 in <br /> 1/2 in. EMT Conduit 79153 24 1 1/8 in. <br /> CONDUIT COMPRESSION NUT <br /> CONNECTOR , <br /> � ADAPTOR BODY <br /> FIGURE 12 GASKET LOCKWASHEft <br /> 000iea NUT—= <br /> "QUIK-SEAL"ADAPTOR FIGURE 14 <br /> The"Quik-Seal"adaptor is a listed mechanical bulkhead fitting that 00015� <br /> produces a liquid-tight seai around both distribution piping and <br /> detection conduit which runs through restaurant hoods and ducts. "HOOD SEAL"ADAPTOR ASSEMBLY <br /> The "Quik-Seal" adaptor accepts threaded pipe or conduit. The This adaptor assembly is a mechanical bulkhead fitting that pro- <br /> adaptor is availabie for 1/4 in. (Part No. 78195), 3/8 in. (°art No duces a liquid-tight seal around 1/2 in. EMT conduit when <br /> 77284), 1/2 in. (Part No 77286), or 3/4 in. (Part No 77288) pipe installing the detection line through restaurant hoods and duct. <br /> or conduit sizes. When using with EMT conduit, a conduit con- The adaptor accepts a high temperature pulley elbow and, when <br /> nector must be instalied in each end of the adaptor The "Quick- used, correctly positions the elbow or conduit in line with the con- <br /> Seal" Adaptor Shipping Assembly must be ordered as stated duit adaptor hole in the detector bracket. The "Hood Seal" elimi- <br /> betow nates the need for multiple elbows when penetrating the top of a <br /> Shipping hood when installing the detection line "Hood Seal"Adaptors are <br /> Assembly Hole Size available in quantities of 6 as Shipping Assembly Part No 423253. <br /> Size Part No. Qry_ Req.uired <br /> 1/4 in. 78196 24 3I4111. SEALNUT <br /> 3/8 in. 77285 24 1 1/8 in / <br /> 1/2 in 77287 24 1 1/8 in. sEA� /� WASHER <br /> 3/4 in. 77289 24 1 3/8 in ADAPTOR <br /> — ADAPTOR BODY BODY--► <br /> GASKET <br /> GASKE'i O <br /> LOCKWASHER PULLEY Q <br /> ELBOW � <br /> (NOT PART <br /> OF ASSEMBLY) <br /> NUT <br /> FIGURE 15 <br /> il�p�Sn <br /> FIGURE 13 <br /> 000154 <br />