12-12801 - Laserfiche WebLink

Browse Search

dn-6927:a � ,.FC'PS=24S6(C/E) � FCPS- o 2458(C/E) (�J N OT 1 F 1 E R _ 6- � a-Amp 24.voit by H o n eywe I I Remote Power Su lies General The FCPS-24S6E (6-amp) and FCPS-24SSE (8-amp) are remote power supplies with battery charger The FCPS-24S6/- 24S8 may be connected to any 12 or 24 volt fire alarm control panel (FACP) or may be used as stand-alone supplies. Pri- mary applications include notification appliance (bell) circuit (NAC)expansion(to support ADA requirements and NAC syn- chronization) or auxiliary power to support 24 volt system accessories. The FCPS-24S6/-24S8 provides regulated and fiitered 24 VDC power to four notification appiiance circuits �. configured as either four Class B(Style Y)or Class A(Style Z, with ZNAC-4 option module).Alternately,the four outputs may be configured as all non-resettable, all resettable or two non- resettable and two resettable. The FCPS-24S6/-24S8 also contains a battery charger capable of charging up to 18 AH batteries. FCPS-24S6C&FCPS-24SSC are U�C-listed. NOTE: Unless otherwise specified, the terms FCPS-24S6 and FCPS-24S8 used in this document refers to the standard FCPS- 24S6 and FCPS-24S8, FCPS-24S6C and FCPS-24S8C, the FCPS-24S6E and FCPS-24S8E P I1P8 Features Includes integral battery charger capable of charging up to • UL-Listed NAC synchronization using System Sensor, • 18 AH batteries.Cabinet capable of housing 7.0 AH batter- Whee►ock,or Gentex"Commander�"appliances. ies. • Operates as a "sync-follower" or as a "sync-generator' • Battery charger may be disa4led via DIP switch for applica- (default). See note on page 2. tions requiring larger batteries. • Contains two fully-isolated inpuVcontrol circuits - triggered • Fixed, clamp-type terminal blocks �ccommodate up to 12 from FACP NAC (NAC expander.mode)or jumped perma- AWG(3.1mm2)wire. nently"ON"(stand-alone mode). - • • Four ciass B (Style Y) or four Class A (Style z, wim Specifications ZNAC-4 module)NACs. Primary(AC)Power: • 6-amp (FCPS-24S6) or 8-amp (FCPS-24S8) full load out- put, with 3 amps maximum/circuit, in NAC expander mode • FCPS-24S6C/-24S8C� 120 VAC,60 Hz,3.2A maximum. (UL 864). • FCPS-24S6E/-24S8E. 240 VAC,50 Hz, 1.6A maximum. • 4-amp (FCPS-24S6) or 6-amp (FCPS-24S8) continuous • Wire Size. minimum#14 AWG(2.Omm2)with 600 V insula- output in stand-alone mode(UL 1481). tion. • Compatible with coded inputs;signals passed through. Controi Input Circuit: • Optional power-supervision relay(EOLR-1). • Trigger Input Voltage: 9 to 32 VDC;. • In stand-alone mode, output power circuits may be config- • Trigger Current: 2.0 mA(16-32 V);Per Input: 1.0 mA(9 ured as: resettable, (reset line from FACP required), -16 V). non-resettable,or a mix of rivo and two. Trouble Contact Rating: 5 A at 24 VDC. • Fully regulated and filtered power output-optimal for pow- puxillary Power Output: Specific application power 500 mA ering four-wire smoke detectors, annunciators, and other system peripherals requiring regulated/filtered power. maximum. • Power-limiting technology meets UL power-limiting require- �utput Circuits: ments. • +24 VDC filtered,regulated. • Form-C normally-closed trouble relay. • 3.0 A maximum for any one circuit. • Fully supervised power supply,battery,and NACs. • Total continuous current for all outputs(stand-alone mode): • Selectable earth fault detection. —FCPS-24S6. 4.0 A maximum • AC trouble report selectable for immediate 2-hour delay.. —FCPS-24S8: 6.0 A maximum. • Works with virtually any UL 864 fire alarm control which uti- • Total short-term current for all outputs(NAC expander mode): lizes an industry-standard reverse-polarity notification cir- —FCPS-24S6: 6.0 A maximum. cuit(including unfiltered and unregulated bell power). —FCPS-24S8: 8.0 A maximum. • Requires input trigger voltage of 9-32 VDC. • Self-contained in compact,Iocking cabinet-15"H x 14.5"W Secondary Power(Battery)Charging Circuit: x 2.75"D(cm:38.1 H x 36.83W x 6.985D). • Supports lead-acid batteries only. • Float-charge voltage: 27.6 VDC. dn-692�:a•04/30/09—Page 1 of 2