Laserfiche WebLink
TRI�JITY ERD <br /> o [.1 ii iS�diidiiuil vi PrGSidTi Siai�ZC Sti"I� SlliilGiZS dClt� �vvZa�riei oivCKCi �i'aiiZ� �ii iN �ill�iyi25 Si�aii <br /> comply with the manufacturer's current published instructions <br /> 6.3 Asphalt Shingles: <br /> 6 3 1 Insiallation of asp",�;' shingles shall comply with the manufacturer's current published <br /> instructions, using minimurri �our (4) naiis per shingie in accoruane,e with FBi; Sections I507.2 <br /> or R905 2, with the following exceptions• <br /> � Camelot, Camelot II / Camelot 30, Camelot IR, Grand Slate II, Country Mansion II, Monaco <br /> and Woodland require minimum five (5) fasteners per shingle <br /> 6.3.2 Fasteners shall be in accordance with manufacturer's published requirements, but not less than <br /> FBC 1507 2.6 or R905 2 5. Staples are not permitted. <br /> 6 3 3 Where the roof slope exceeds 21 units vertical in 12 units horizontal, spe�cial methods of <br /> fastening are required. Contact the shingle manufacturer for details <br /> 6.4 Hip & Ridge Shingles: <br /> 6.4.1 Installation of Ridglass 8, Ridglass 10 and Ridglass 12 asphalt shingles shall comply with the <br /> manufacturer's current published instructions with a minimum two (2) nails per side [total of <br /> four (4) nails per shingle] and asphalt roofing cement. <br /> 6 4 2 Installation of SeaI-A-Ridge and SeaI-A-Ridge Armorshield asphalt shingles shall comply with <br /> the manufacturer's current published instructions with a minimum two (2) nails per shingle. <br /> 6.4.3 Installation of Timbertex Hip and Ridge asphalt shingles shall comply with the manufacturer's <br /> current published instructions with a minimum two (2) nails per shingle and beads of <br /> Sonneborn NP1 Gun Grade Polyurethane Sealant, Henkel PL Roofing and Flashing Sealant or <br /> TopCoat FlexSeal Adhesive. <br /> 6.4 4 Fasteners shall be in accordance with the manufacturer's published requireme�nts, but not less <br /> than FBC 1507.2 6 or R905.2 5. Staples are not permitted <br /> 7. LABELING: <br /> 7.1 Each unit shall bear a permanent label with the manufacturer's name, logo, city, state and logo <br /> of the Accredited Quality Assurance Agency noted herein <br /> 7 2 Asphalt shingle wrappers shall indicate compliance with one of the requira_d classifications <br /> detailed in FBC Table 1507 2.7.1 / R905.2.6.1 <br /> S• BUILDING PERMIT REQUIREMENTS: <br /> As required by the Building Official or Authority Having ]urisdiction in order to prop�°rly evaluate the <br /> installation of this product. <br /> 9. MANUFACTURING PLANTS: <br /> Contact the named QA entity for information on which plants produce products covered by Florida Rule <br /> 9N-3 QA requirements. <br /> lO. QUALITY ASSURANCE ENTITY: <br /> Underwriters Laboratories — QUA1743; (847) 664-3281 <br /> - END OF EVALUATION REPORT - <br /> Exterior Research and Design, LLC. Evaluation Report 01506.01.08-R7 <br /> Certificate of Authorization#9503 FL10124-RS <br /> . Revision 7: 12/12/2011 <br /> Page 4 of 4 <br />