12-13462 - Laserfiche WebLink

Browse Search

GENERAL NOTES 1. All wires at Control Panel must be tagged and marked in order for SimplexGrinnell Technical Representatives to make final connections. 2. All wires and shields to be free of shorts and grounds. 3. A MINIMUM of 3/4' conduit shall be used. All conduit should be sized per NFPA 70 (NEC). The following conditions shall be maintained: a) EMT in ceiling spaces. b) Rigid conduit or PVC in slabs with rigid elbows. If Flex conduit is used, the following applies: a) Flex conduit runs shall NOT exceed 72 ". b) Only Metal Flex shall be used. C This drawing depicts general locations of Life Safety equipment & field devices. Exact routing of conduits to be determined in the field by the Installing Contractor to suit conditions. All changes shall be clearly indicated on the record drawings. NFPA 72 2007 (Section 10.6.1.1). 5. Device locations and quantities must be confirmed with approved Fire Alarm shop drowing submittals. Any discrepancies which exist between the approved shop drawings and the contract documents shall remain the responsibility of the Installing Contractor. 6. Should any conditions exist that differ from what is indicated on these drawings which cause major deviations in the work shown, the Contractor shall contact SimplexGrinnell Engineers in a timely manner so as not to impair the construction schedule. 7. The Contractor is responsible for making and obtaining approval for all necessary adjustments in circuiting as required to accommodate the relocation of equipment and /or devices which are affected by any authorized change. All changes shall be clearly indicated on the record drawings. NFPA 72 2007 (Section 10.6.1.1). 8. Wiring and mounting of Fire Alarm devices may NOT begin until a Fire Alarm Permit has been issued by the Authority Having Jurisdiction, by order of the Fire Marshal. 9. NFPA 72, Audible/Visual and Visual only devices shall be mounted with the entire lens between 80' and 96' above the finished floor (NFPA 72 2007 Section 7.5.4). Refer to equipment data sheets for exact backbox mounting heights. If ADA applies, Strobes shall be mounted at 80" to the bottom of the Strobe lens (ADAAG Section 4.28.3 (6) 10. Manual Pull Station shall be not less than 3 1/2 ft (1.1 M) and not more than 4, 1/2 ft (1.37 M) from operable part of device to finished floor level and within 5 ft of doorway opening, per NFPA 72 2007 (Section 5.13.4 and 5.13.6). 11. Provide dedicated 120vac circuits to the Fire Alarm Control Panel and NAC Panels. Lobel dedicated circuit "Fire Alarm System" and place lock out on circuit at the Electrical Panel. NFPA 72 2007 (Section 4.4.1.4). 12. Existing conduits may be used by Installation Contractor as deemed necessary. However, any existing conduit will be used only if conduits meet current standards and codes. SimplexGrinnell makes NO statements written or verbal as to the condition of the existing conduit. 13. Installing Contractor to verify audibility level of the Audible devices and field adjust to ensure audibility is in compliance with NFPA 72 2007 (Section A.7.4.2) min. 14. DO NOT install Smoke Detector heads until all major construction and cleaning is complete. Cleaning of detector heads contaminated by construction duct will be billable. NFPA 72 2007 (Section 5.7.1.11). SOUND LEVELS NFPA 72, 7.4.2.12007 Edition LEGEND To ensure that audible public mode signals are clearly heard, unless otherwise permitted by 7.4.2.2 through 7.4.2.5, they shall have a sound level at least 15 dB above the average ambient sound level or 5 dB above the maximum sound level having a duration of at least 60 seconds, whichever is greater, measured 1.5 m (5 ft) above the floor in the occupioble are, using A- weighted scale (dBA). ABOVE FINISHED FLOOR NFPA 72, TABLE A7.4.2 2007 Edition Average Ambient Sound Level According to Location Location Average Ambient MEETS THE SOUND LEVEL OUTPUT Sound Level (dBA) Business occupancies 55 Educational occupancies 45 Industrial occupancies 80 Institutional occupancies 50 Mercantile occupancies 40 Mechanical rooms 85 Piers and water - surrounded structures 40 Places of assembly 55 Residential occupancies 35 Storage occupancies 30 Thoroughfares, high density urban 70 Thoroughfares, medium density urban 55 Thoroughfares, rural density urban 40 Tower occupancies 35 Underground structures and 40 windowless buildings OVERALL SHIELD (YELLOW) Vehicles and vessels 50 PRIMARY POWER SUPPLY NFPA 72 2007 CHAPTER 4.4.L4 Primary Power Supply. CHAPTER 4.4.1.4.1 Dedicated Branch Circuit. A dedicated branch circuit of one of the following shall supply primary power. CHAPTER 4.4.1.4.2 Mechanical Protection. 4.4.1.4.2.1 The dedicated branch circuit(s) and connections shall be mechanically protected. 4.4.1.4.2.2 Circuit disconnecting means shall have a red marking, shall be accessible only to authorized personnel, and shall be identified as "FIRE ALARM CIRCUIT'. 4.4.1.4.2.3 The location of the circuit disconnecting means shall be permanently identified at the fire alarm control unit. SCOPE OF WORK Add to existing Fire Alarm System as shown on the drawings. All wiring to be "CLASS B'. Wiring is "STYLE Y' for Notification Appliance Circuits. 'STYLE B" for Initiating Device Circuits and STYLE 4" for Signaling Line Circuits. New initiating devices will tie to existing IDnet. New Notification device strobe circuit will tie to New NAC Expander panel. New Notification device speaker circuit will tie to existing circuit Trip new NAC Expander panel from existing IDnet. DEVICE MOUNTING HEIGHTS (PER NFPA 72) NFPA 72 2002 EDmoN NFPA 72 2007 EDITION (SECTION A.5.6.3.1) THE 4' REQUIREMENT FOR SMOKE DETECTORS HAS BEEN REMOVED FROM THE 2010 EDITION OF NFPA 72 4' NOTE: MEASUREMENTS (102mm) SHOWN ARE TO THE CEILING CLOSEST EDGE OF THE �1I ITN -�7 DETECTOR. VICOILING MOUNTED 4" SMOKE/HEAT DETECTOR 0 o�mm) 12' MAX) (305mm MAX) ACCEPTED HERE NEAT DETECTORS NEVER HERE NFPA 72 2010 EDITION WALL MOUNTED (SECTION 17.7.3.2.1) SMOKE/HEAT DETECTOR VISUAL APPLIANCE MOUNTING HEIGHT CONSIDERATIONS IN SLEEPING ROOMS 1. MIN DISTANCE IN SLEEPING ROOMS IS 24' (61Omm) TO TOP OF LENS FOR 11OCD STROBES WITHIN 16' OF THE PILLOW 2. 177CD STROBES, USED IN SLEEPING ROOMS, CAN BE WITHIN THE 24' (610mm) MINIMUM DISTANCE FROM THE CEILING. THE HIGHER INTENSITY IS TO COMPENSATE FOR A POSSIBLE SMOKE LAYER. FOR CEILING HEIGHTS LESS THAN 86' (2180mm), THE VISUAL LENS MOUNTING HEIGHT SHALL BE WITHIN 5" (150mm) OF THE CEILING. AUDIBLE ONLY AUDIBLE/VISUAL & VISUAL ONLY APPLIANCES SYNCHRONIZE MORE THAN TWO APPLIANCES IN ANY FIELD OF VIEW. NFPA 72 2002 EDITION (SECTION A.75.4.3) NFPA 72 2007 EDITION (SECTION A.7.5.4.5) NFPA 72 2010 EDITION (SECTION 18,5.4,3.2(4)) REF. 80' MIN (IBC) (2032mm MIN) REF. 96" MAX (IBC) (2440mm MAX) ABOVE FINISHED FLOOR 80" (ADA) 80" MIN (NFPA) NFPA 72 2002 EDITION (SECTION 7.5.4) NFPA 72 2007 EDITION (SECTION 7.5.4.1) NFPA 72 2010 EDITION (SECTION 18.5.4.1)' NOTE: REFER TO THE PROPER DEVICE INSTALLATION INSTRUCTIONS FOR BACKBOX MOUNTING HEIGHT. 96' MAX (NFPA) (2440mm MAX) ABOVE FINISHED FLOOR (2032mm) (2032mm MIN) FINISHED FLOOR A/C SUPPLY OR RETURN DIFFUSER i 3' (MIN) (914mm MIN) NFPA 72 AUDIBLE APPLIANCE LEGEND 6" MIN (152.4mm MIN) DESCRIPTION BELOW FINISHED CEILING MOUNTING HEIGHTS 90" MIN (2286mm MIN) NOTIFICATION APPLIANCE CABINET ABOVE FINISHED FLOOR NON- PLENUM RATED: FPL (OTHER MOUNTING HIEGHTS SHALL BE PERMITTED BY THE AW PROVIDING IT MEETS THE SOUND LEVEL OUTPUT REQUIRED.) FIRE ALARM TERMINAL CABINET FURNISH BY OTHERS TO EXIT DOOR © MANUAL PULL STATION 5' (MAX.) 48' TO CENTER OF DEVICE AFF .5W # (1524mm) DOOR WIDTH PAIGE 454722AREM 80 PAIGE 454717AREM LESS 3 SIMPLEXGRINNELL 4906 -9151 82' TO BOTTOM OF BACKBOX AFF 160 6mm) AREA = 0.0755 SQ. INCH AREA = 0.1085 SO. INCH 208 BELDEN 5320FJ STROBE WALL MOUNT MANUAL 80' TO BOTTOM OF BACKBOX AFF 17 '#" DENOTES CANDELA 49 PULL EOL END -OF -LINE RESISTOR (SIZE & QTY) TO BE DETERMINED IN FIELD 1 PAIR, 1S AWG, TWISTED OVERALL SHIELD (YELLOW) STATION (USE RESISTOR CHART AS A GUS NON - PLENUM RATED: FPL O FIRE SIMPLEXGRINNELL 4098 -9714 5' (127mm) PHONE ANIXTER SG1802S10 -03 MAGNETIC JACK 68 AREA = 0.0320 SQ. INCH AREA= 0.0186 SO. INCH DOOR o ® PAIGE 454722AREM HOLDER PAIGE 454717ARE PAIGE 73182CI PAIGE 73182CIC 48" MAX (ADA) (1219mm) 42" MIN /54' MAX (NFPA) (1067mm MIN /1372mm MAX NFPA 72 2002 EDITION 35 (SECTION 5.12.4) BELDEN 5320FL NFPA 72 2007 EDITION NFPA 72 2010 EDITION (SECTION 5.13.4) (SECTION 17.14.4) IMPORTANT NOTICE TO USER By accepting or using this drawing and /or the information contained herein, the user agrees to the following terms and conditions: The electronic information in the drawing may be subject to intentional or unintentional alteration. Any use, reuse, copying modification or alteration of the information contained herein shall be at the sole risk of the user. This information may not be sold or transferred to any third party, used on other projects or additions to the project for which it was prepared, or used for completion of this project by any third party. SimplexGrinnell disclaims all liability for the use or reuse of altered files by the user or any third party and such use will be a users sole risk. User shall, to the fullest extent permitted by law, defend, indemnify, and hold SimplexGrinnell harmless from n any and all claims for loss, damage or injury arising directly or indirectly therefrom. FIRE ALARM LEGEND SYMBOL DESCRIPTION VENDOR / PART NUMBER MOUNTING HEIGHTS PAIR, 18 AWG, TWISTED OVERALL SHIELD (RED) NOTIFICATION APPLIANCE CABINET M NON- PLENUM RATED: FPL NAC w /6.2M BATTERY SETS SIMPLEXGRINNELL 4009- 9201 60' TO CENTER OF PANEL FATC I FIRE ALARM TERMINAL CABINET FURNISH BY OTHERS • © MANUAL PULL STATION SIMPLEXGRINNELL 4099- 9001 48' TO CENTER OF DEVICE AFF .5W # SPEAKER /STROBE PAIGE 454722AREM 80 PAIGE 454717AREM WALL. MOUNT SIMPLEXGRINNELL 4906 -9151 82' TO BOTTOM OF BACKBOX AFF 160 '.25W' DENOTES WATT TAP ' #' DENOTES CANDELA AREA = 0.0755 SQ. INCH AREA = 0.1085 SO. INCH 208 BELDEN 5320FJ STROBE WALL MOUNT SIMPLEXGRINNELL 4906 - 9101 80' TO BOTTOM OF BACKBOX AFF 17 '#" DENOTES CANDELA 49 AREA= 0.0269 SQ. INCH EOL END -OF -LINE RESISTOR (SIZE & QTY) TO BE DETERMINED IN FIELD 1 PAIR, 1S AWG, TWISTED OVERALL SHIELD (YELLOW) 2 HOUR RATED (USE RESISTOR CHART AS A GUS NON - PLENUM RATED: FPL O SMOKE DETECTOR SIMPLEXGRINNELL 4098 -9714 ' ANIXTER SG1802S19 -03 ANIXTER SG1802S10 -03 SIMPLEXGRINNELL 4098 -9792 50 FINISHED WALL SIDE WALL 215 110 (Total CKT Load: 0.924 amps) V2 Re 1` (X3) (x1) (0) 2S V 75 25W (Total CKT Load: 0.634 a 15 amps) V1 EOL Re (x3) (XI) (6) V CABLE TROUGH NAC FATC 4009 DEDICATED 200 VAC '00 MUNO OF" srslor CR !"D Two _ 0WM0'A`%ff6V MM M,2S M (x2) (0) TO EXISTING PARTIAL SYSTEM RISER FIRE ALARM SYSTEM NOT TO SCALE ON NOT U: DIP SWITCHES 1 THRU 4 IDNET ADDRESS CHART MSB DIPSWITCH IS SHOWN g JX SET AT ADDRESS 2 I -ONIM O -OFF19 I DIP SWITCHES 5 THRU 8 ED FIRE ALARM WERE LIST 1000 IDNET CIRCUIT - 1 PAIR, 18 AWG, TWISTED OVERALL SHIELD (RED) 2 HOUR RATED M NON- PLENUM RATED: FPL 1110 PLENUM RATED: FPLP NON- PLENUM RATED: FPLR -CI NON- PLENUM RATED: FPL -NPFL 0101 ANIXTER S131802S19 -03 0011 AND(TER SG1802S21 -03 0111 1111 AREA = 0.0320 SQ. INCH 0 AREA= 0.0177 SQ. INCH 32 48 PAIGE 454722AREM 80 PAIGE 454717AREM PAIGE 73182CI PAIGE 73182CIC 128 AREA -- 0.0224 SQ. INCH 160 AREA= 0.0219 SQ. INCH AREA = 0.0755 SQ. INCH AREA = 0.1085 SO. INCH 208 BELDEN 5320FJ 240 BELDEN 6320FJ BELDEN 5320FM 17 AREA--0.0350 SQ. INCH 49 AREA= 0.0269 SQ. INCH AREA = 0.0774 SQ. INCH 97 SPEAKER CIRCUIT - 1 PAIR, 1S AWG, TWISTED OVERALL SHIELD (YELLOW) 2 HOUR RATED S NON - PLENUM RATED: FPL NON- PLENUM RATED: FPLR PLENUM RATED: FPLP NON - PLENUM RATED: FPLR -CI NON- PLENUM RATED: FPL -NPFL 0100 ANIXTER SG1802S19 -03 ANIXTER SG1802S10 -03 ANIXTER SG1802S21 -03 50 68 AREA = 0.0320 SQ. INCH AREA= 0.0186 SO. INCH AREA= 0.0177 SQ. INCH 130 146 PAIGE 454722AREM PAIGE 454722ARE PAIGE 454717ARE PAIGE 73182CI PAIGE 73182CIC 226 AREA--0.0224 SQ. INCH AREA= 0.0204 SQ. INCH AREA= 0.0219 SQ. INCH AREA =0.0755 SQ. INCH AREA = 0.1085 SQ, INCH 35 BELDEN 5320FJ BELDEN 5320FL BELDEN 6320FK BELDEN 532OFM 115 AREA = 0.0350 SO. INCH AREA = 0.0189 SO. INCH AREA= 0.0269 SQ. INCH AREA = 0.0714 SO. INCH 195 VISUAL /SIGNAL CIRCUIT - 2 CONDUCTOR, 14 AWG SOLID (ORANGE /BROWN') 2 HOUR RATED V NON- PLENUM RATED: FPLR CONDUIT ONLY: THHN PLENUM RATED: FPLP NON- PLENUM RATED: FPLR -CI NON- PLENUM RATED: FPL -NPFL 68 ANIXTER SG1402N10 -03 ANIXTER ANIXTER SG1402N21 -03 ANIXTER SG1402N40 -03 148 AREA--0.0340 SQ. INCH AREA= 0.0097 SQ. INCH AREA= 0.0308 SQ. INCH AREA = 0.1018 SO. INCH 228 PAIGE 454718RE PAIGE 740252RDBK PAIGE 454719ARE PAIGE 73142CI PAIGE 73142CIC 37 AREA= 0.0380 SQ. INCH AREA= 0.0394 SO. INCH AREA= 0.0333 SO. INCH AREA = 0.1195 SO. INCH AREA = 0.1195 SQ. INCH 117 BELDEN 512OUL BELDEN BELDEN 6120UL BELDEN 51 20U BELDEN 5120OZ 197 AREA -- 0.0356 SQ. INCH AREA= 0.0097 SQ. INCH AREA= 0.0330 SO. INCH AREA = 0.1018 SO. INCH AREA = 0.1134 SQ. INCH 5 CONDUIT SIM 38 CONDWOR AREA CONDUIT SM CONDUCTON AREA NOTE: WHEN THE ADM LISTED GABLES ARE INSTALLED N CONDUIT (REQUIRET) FOR CIC LISTED GABLES) 1/2- 3/4' 0.12 SQ NCH • 0.21 SQ NCH • 1-1/4' 1 -1 2' 0.00 so I" 082 gQ { • 182 1' 214 0.34 SQ NCH • 248 Z( 1.34 s4 NCH • ONLY CIRCUIT NTEGRITY CABLES CAN BE NSTALED IN THAT CONDUIT. THE CABLES SPECIFIED HERE ARE FOR REFERENCE OF REQUIRED ELECTRIC& CHARACTERISTICS AS • 40x FILL PER N.E.C. 55 71 CONTACT YOUR LOCAL 8MPLEXC i1M1E11. OF�10E WEIL AS CODE REQUIREM MS. ALTERNATE SUPPLIERS MAY BE SUBSTITUTED PROMNG 151 167 183 199 EQUNALEM CHARACTERMM ARE MAINTAINED , M3AS SUCH AS CAPACITANCE BETWEEN 231 FOR ANY CABLE SUBSTTTUTKM 0001 CONDUCTORS AND WIRE GAUGE CM BE CM Ai. TO THE CIRCUIT DESIGN OF THIS srsa INSTALLATION. FINISHED WALL SIDE WALL 215 110 (Total CKT Load: 0.924 amps) V2 Re 1` (X3) (x1) (0) 2S V 75 25W (Total CKT Load: 0.634 a 15 amps) V1 EOL Re (x3) (XI) (6) V CABLE TROUGH NAC FATC 4009 DEDICATED 200 VAC '00 MUNO OF" srslor CR !"D Two _ 0WM0'A`%ff6V MM M,2S M (x2) (0) TO EXISTING PARTIAL SYSTEM RISER FIRE ALARM SYSTEM NOT TO SCALE ON NOT U: DIP SWITCHES 1 THRU 4 IDNET ADDRESS CHART MSB DIPSWITCH IS SHOWN g JX SET AT ADDRESS 2 I -ONIM O -OFF19 aa.. 0 J Lu X Z (n 4 . �� a. Iq W cri �Q 0 O 1� V Q Div LL 0N0 ONO M M { ® Im fD fD ei L m Q tND tN0 (D 0 Q. MMM LL IS DO 00 00 v° Q u- LJ.I V� Q UJ F1 i 0 U Z O a N Q 0 W R 0 d Z O I,-,, N E-4 W U E-1 H co J [� LL Z DO _ Z w �oQ F+4 F+4 r% ti N DRAWN BY: DATE: J,SERRANO 30- JULY -2012 CONFIGURED BY: DATE: J.SERF I 30- JULY -2012 REVIEWED BY: DATE: J.SERRANO 30- JULY -2012 PROJECT NUMBER: 965620413 SHEET TITLE: GENERAL INFORMATION FIRE ALARM SYSTEM SHEET NUMBER: FA -002 I DIP SWITCHES 5 THRU 8 ED 0000 1000 0100 1100 0010 1010 0110 1110 0001 1001 0101 1101 0011 1011 0111 1111 0000 0 16 32 48 64 80 96 112 128 144 160 178 192 208 224 240 1000 1 17 33 49 65 81 97 113 129 145 161 177 193 209 225 241 0100 2 18 34 50 68 82 98 114 130 146 162 118 194 210 226 142 1100 3 19 35 51 67 83 99 115 131 147 183 179 195 211 227 243 0010 4 20 38 52 68 84 100 116 132 148 164 180 196 212 228 244 1010 5 21 37 53 69 85 101 117 133 149 165 181 197 213 229 245 0110 5 22 38 54 70 86 102 118 134 150 166 182 198 214 230 248 1110 7 23 39 55 71 87 103 119 135 151 167 183 199 215 231 247 0001 8 1 24 40 56 72 88 104 120 136 152 168 184 200 216 232 248 1001 9 F 25 41 57 73 89 1D5 121 137 153 169 185 201 217 233 249 0101 10 1 26 42 58 74 90 106 122 138 154 170 186 202 218 234 250 1101 11 1 27 43 59 75 1 91 107 123 139 155 171 187 1 203 219 235 0011 12 28 44 60 76 92 108 124 140 156 172 188 204 220 238 1011 13 29 45 61 77 93 109 125 141 157 173 189 205 221 237 0111 14 30 48 62 78 94 110 126 158 174 190 208 222 238 1111 15 31 47 63 79 95 111 127 E143 -1-59-Fl 59 7_ 175 191 207 223 239 aa.. 0 J Lu X Z (n 4 . �� a. Iq W cri �Q 0 O 1� V Q Div LL 0N0 ONO M M { ® Im fD fD ei L m Q tND tN0 (D 0 Q. MMM LL IS DO 00 00 v° Q u- LJ.I V� Q UJ F1 i 0 U Z O a N Q 0 W R 0 d Z O I,-,, N E-4 W U E-1 H co J [� LL Z DO _ Z w �oQ F+4 F+4 r% ti N DRAWN BY: DATE: J,SERRANO 30- JULY -2012 CONFIGURED BY: DATE: J.SERF I 30- JULY -2012 REVIEWED BY: DATE: J.SERRANO 30- JULY -2012 PROJECT NUMBER: 965620413 SHEET TITLE: GENERAL INFORMATION FIRE ALARM SYSTEM SHEET NUMBER: FA -002