12-13600 - Laserfiche WebLink

Browse Search

SpectrAlert Advance Specifications . . General SpectrAlert Advance strobes and horn strobes shall mount to a standard d:,d r 1 Y-inch back box,4-inch octagon back box.or double- gang back box.Two-wire products shall also mount to a single-gang 2 x 4 x 17'8-inch back box.A universal mounting plate shall be used to mountmg ceiling and wail products.The notification appliance circuit w�inng shall terminate at the universal mounting plate.Also S�ectrAlart Advance products,when used with the Sync•Circuit'"Module accessor� shail be powered from a non-coded noUfication appliance circuit output and shall operate on a nominal 12 or 24 votts.When used with the Sync•Circuit Module, 12-volt-rated notification appliance circui; outputs shall operate between 9 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 1�and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supp�y.Strobes and hom strobes shall have f�eld-selectable candela settings including 15 15/75 30,75,95 110 115 135 150, 177 and 185. Strobe The strobe shall be a Svstem Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service The strobe shall be wired as a primary-signaling notiflcation appliance and comply with the Americans with Disabilities Act reqwrements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range The strobe light shall consist of a xenon flash tube and associated Ienslrefiector system. Horn Strobe Combinatiun The hom strobe shall be a System Sensor SpectrAlert Advance Model hsted to UL 1971 and UL 464 and shail be approved for fire protective service.The hom strobe shall be wired as a primary-signaling notification appliance and comply with the Americans w�th Disabtlities Act requirements for visible signaling appliances tlashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lenslreflector system.The hom shall have three audibdity options and an option to switch between a temporal three pattern and a non-temporal(continuous)patlern.Ttiese options are set by a multiple position switch.On four-wire products,the strobe shall be powered independently of the sounder.ihe horn on hom strobe models shall operate on a coded or non-codeJ power supply. Synchronization Module The module shall be a System Sensor Sync•Circuit model MDL listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and homs at temporal three.Also wh�le operating the strobes.the module shall silence the horns on hom strobe models over a single pair of wires.The module shall mount to a 411�16 x 411�16 x 21!8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chainmg two or more synchronizatien modules together will synchronize all the zones they controL The module shall not operate on a coded power supply Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Fiash Rate 1 flash per sec�nd Nominal Voltage Regulated 12 DC!FWR or regulated 24 UC/FWR' Operating Voltage Rang�e2 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) InputTerminal Wire Ga�age 12 to 18 AWG Ceiling-Mount Dimensions(including lens) 6.8 diameter x 2.5 high(173 mm diameter x 64 mm high) Ceiling-Mount Back Box Skirt Dimensions(BBSG2.BBSCW-2) 7 1 diameter x 22""high(180 mm diameter x 57 mm high) Ceiling-MountTrim Riny Dimensions(sold as a 5 pack)(TRC-HS, 6.9 diameter x 0.35 high(175 mm diameter x 9 mm high) TRCW-HS) Notes: 1 Fuli Wave Rectified(f=�NR)voltage is a non-regulated hme-varying pcwer source tha[is used on some power suppiy and panel outputs. 2 P,S,PC,and SC products will operate at 12 V nominal onlv for 15 and 15/75 cd ��c_��_.