|
10. MINIMUM WIRE SIZE SHALL BE #12 AWG, EXCLUDING CONTROL WIRING. UNLE55 OTHERWISE NOTED,
<br />CONDUCTORS SHALL BE COPPER WITH THWN/THHN INSULATION. CONDUCTORS #12 AND SMALLER
<br />MAY BE SOLID; ALL THOSE #10 AND LARGER TO BE STRANDED.
<br />II. ALL UNDERGROUND RAGEWAY5 SHALL BE GALVANIZED RIGID STEEL CONDUIT OR SCHEDULE 40
<br />PVC. ALL OTHER RAGEWAY5 TO COMPLY WITH GOVERNING CODES. MINIMUM CONDUIT
<br />UNDERGROUND SHALL BE 3/4" CONDUIT UNLESS OTHERWI5E NOTED.
<br />12. OUTLET 'BOXE5 SHALL BE PRE55ED STEEL IN DRY LOCATIONS, CAST ALLOY WITH THREADED
<br />HUB5 IN WET OR DAMP LOCATIONS, AND BE OF SPECIAL CONSTRUCTION FOR OTHER GLA551FIED
<br />AREAS. ALL BOXES SHALL BE RECESSED (FLUSH) IN WALLS OR CEILING5 WHENEVER POSSIBLE.
<br />13. DISCONNECT SWITCHES SHALL BE H.P. RATED, GENERAL DUTY, QUICK -MAKE, QUICK -BREAK TYPE,
<br />ENCLOSURES SHALL BE AS REQUIRED BY N,E.G. AND LOCATION (WEATHERPROOF, EXPLOSION -
<br />PROOF, ETC.).
<br />14. ALL GENERAL PURPOSE SWITCHES AND RECEPTACLES SHALL BE THE PRODUCT OF A SINGLE
<br />MANUFACTURER. LEVITON, HUBBELL, PASS d SEYMOUR, OR ARROW HART WILL BE ACCEPTED.
<br />DEVICE TYPES AND COLOR SHALL MATCH BUILDING STANDARD.
<br />15. ALL RACEWAYS AND PIPES, SPACED IN OR THROUGH ANY CONCRETE SLAB, SHALL BE 5PAGED
<br />A MINIMUM OF THREE TIMES THE DIAMETER OF THE LARGEST RAGEWAY.
<br />16. IT 15 NOT THE INTENT OF THESE PLANS TO SHOW EVERY MINOR DETAIL OF CONSTRUCTION. THE
<br />GONTRAGTOR IS EXPECTED TO FURNI5H AND INSTALL ALL ITEMS FOR A COMPLETE ELECTRICAL
<br />SYSTEM, AND PROVIDE ALL NEGE55ARY DEVICES AND COMPONENTS FOR EQUIPMENT TO BE
<br />PLACED IN PROPER WORKING ORDER,
<br />17. ALL ELECTRICAL RAGEWAY5 (METALLIC AND NONMETALLIC) SHALL HAVE AN EQUIPMENT
<br />GROUND CONDUCTOR 51ZED IN ACCORDANCE WITH THE LATEST EDITION OF THE N.E.G.
<br />15. LOAD DATA 15 BASED ON INFORMATION GIVEN ENGINEER AT THE TIME OF DESIGN. VERIFY ALL
<br />EQUIPMENT NAMEPLATE RATINGS BEFORE ORDERING.
<br />Iq. CIRCUITS SHOWN ON PLANS ARE TO DETERMINE LOAD UATA AND PANEL SIZES. THE
<br />GONTRACTOR IS TO PROVIDE CIRCUITS AND ROUTING OF CONDUITS TO SUIT JOB CONDITIONS.
<br />20. TANDEM AND HALF -SPACE CIRCUIT BREAKERS SHALL NOT BE USED.
<br />21. ALL UNDERGROUND PVG CONDUIT RUNS SHALL HAVE RiO19 STEEL ELBOW5 AND RIGID STEEL
<br />SECTIONS AT SLAB PENETRATIONS. WHERE RIGID STEEL 6 USED, IT SHALL BE COMPLETELY
<br />COATED WITH AN ALKALI AND RUST - RESISTANT BITUMA5TIG PAINT, AND THREADS SHALL BE
<br />COATED WITH ZING CHROMATE.
<br />22. ALL ELECTRICAL CONDUCTORS SHALL BE INSTALLED IN AN APPROVED RACEWAY.
<br />23. CONTRACTOR SHALL BE RESPONSIBLE FOR SEALING ALL CONDUIT PENETRATIONS MADE
<br />THROUGH FIRE RATED WALLS, CEILINGS, 5LAB5, ETC. PENETRATION SEALS SHALL Be PER U.L.
<br />ASSEMBLY STANDARDS.
<br />24. CONDUIT SYSTEM REQUIREMENTS:
<br />UNDERGROUND - PVG WITH RIGID qO THROUGH SLAB.
<br />ABOVE FIN15H FLOOR, CEILINGS, ETC. (INDOOR) - EMT WITH DIECA5T SET 5CREW FITTINGS.
<br />GALVANIZED RIGID CONDUITS - ABOVE GRADE AND WHERE SUSCEPTIBLE TO PHYSICAL
<br />DAMAGE.
<br />FLEXIBLE CONDUITS - INDOOR, ONLY SHORT RUNS NOT TO EXCEED 6-0 ".
<br />5EALTITE - OUTDOOR, ONLY SHORT RUNS NOT TO EXCEED 6-0 ".
<br />25. CONDUCTOR COLOR CODING:
<br />THE FOLLOWING APPLICABLE COLOR CODES SHALL BE IMPLEMENTED AND P05TED IN ALL
<br />PANELS, DISCONNECT 5WITGHE5, ETC., PER NEC ARTICLEE5 200.6(D) AND 215.12:
<br />120 1205\1., 3 -PH.
<br />PHASE 'A' BLACK
<br />PHASE 'B' RED
<br />PHASE 'G' BLUE
<br />NEUTRAL WHITE
<br />GROUND GREEN
<br />ISOL. GROUND GREEN/YELLOW
<br />+ MG GABLE: METAL -GLAD GABLE
<br />• FOR ALL CIRCUITS; GABLE SHALL BE 'HEALTH GARS
<br />FACILITY METAL GLAD GABLE' TYPE (HGF) ONLY, IN
<br />COMPLIANCE WITH NEG 51-7.13 (A)(B).
<br />• FOR ALL LIGHTING CIRCUITS ABOVE 8'-0" ONLY;
<br />GABLE MAY BE 'METAL GLAD GABLE' TYPE (MG).
<br />• HOME RUNS SHALL REMAIN IN CONDUITS.
<br />• MG GABLE MAY BE USED FOR 20 AMP CIRCUITS IN
<br />WALLS OR ABOVE AGGE551BLE CEILINGS.
<br />• FOR ALL LIGHTING CONTROL SWITCHES, GABLE
<br />SHALL BE 'HEALTH CARE FACILITY METAL GLAD
<br />GABLE' TYPE (HGF) ONLY, IN COMPLIANCE WITH NEG
<br />51 -7.13 (A)(B).
<br />Ng E3
<br />• MG GABLE WIRE 0AUGE5 SHALL BE AS 5HOWN ON
<br />PANEL SCHEDULE.
<br />• MG GABLE SHALL ONLY BE USED WHERE ALLOWED
<br />BY N.E.G. 5EGTION 330.10 AND /OR AS 5HOWN
<br />ABOVE, WHIGHEVER IS MORE STRINGENT.
<br />• WHERE ALLOWED, MG GABLE SHALL BE INSTALLED
<br />PER N.E.G. 330.
<br />• MG GABLE MAY NOT BE U5ED IN OPEN STRUCTURE
<br />AREA.
<br />Na3A
<br />DEMOLITION NOTE5
<br />v
<br />5PEG I F I GAT I ON5
<br />L
<br />I.
<br />ALL WORK SHALL BE IN 5TRICT ACCORDANCE WITH THE LATEST EDITION OF THE NATIONAL
<br />COORDINATE WITH THE GENERAL CONTRACTOR ON SITE TO THE
<br />N
<br />ELECTRICAL CODE (N.E.G.) AND ALL LOCAL GODE5 AND ORDINANCES.
<br />E
<br />2.
<br />ALL MATERIALS SHALL BE NEW AND OF DOMESTIC ORIGIN AND SHALL BEAR UNDERWRITERS'
<br />G
<br />L
<br />LABEL WHERE APPLICABLE.
<br />T
<br />3.
<br />ALL WORK SHALL BE PERFORMED BY A LICENSED ELEGTRIGAL CONTRACTOR IN A FIRST -CLASS
<br />2. ELECTRICAL DEMOLITION WORK SHALL INCLUDE, MT NOT BE LIMITED TO,
<br />A
<br />WORKMANLIKE MANNER. THE COMPLETED SYSTEM 15 TO BE FULLY OPERABLE AND
<br />L
<br />INSTALLATION OF NEW EQUIPMENT AS INDICATED ON THE PLANS.
<br />ACCEPTANCE OF TH15 SYSTEM BY THE ENGINEER/ARCHITECT MUST BE A CONDITION OF THE SUB
<br />3. CONTRACTOR SHALL REMOVE ANY EXPOSED WIRE, CONDUIT, HANGERS,
<br />FLUORESCENT L16HT FIXTURE, LETTER INDICATE-5 TYPE
<br />GONTRAGT,
<br />MAIN 5WITGH113OARD
<br />4.
<br />ALL WORK TO BE COORDINATED WITH OTHER TRADES TO AVOID INTERFERENCE WITH THE
<br />G
<br />MDP
<br />PROGRE55 OF CONSTRUCTION.
<br />T
<br />5.
<br />CONTRACTOR TO GUARANTEE ALL MATERIALS AND WORKMANSHIP FREE FROM DEFECTS FOR A
<br />5. REV15E ALL EX15TINO PANEL DIRECTORIES TO REFLECT ALL REVI5ION5.
<br />KEYNOTES
<br />PERIOD OF NOT LE55 THAN ONE (1) YEAR FROM DATE OF ACCEPTANCE.
<br />L.
<br />6.
<br />CORRECTION OF ANY DEFECTS TO BE COMPLETED WITHOUT ADDITIONAL CHARGE AND TO
<br />CONSTRUCTION. VERIFY SPECIFIC LOCATIONS WITH OWNER'S AUTHORIZED
<br />Q
<br />INCLUDE REPLACEMENT OR REPAIR OF ANY OTHER PHASE OF THE INSTALLATION WHIGH MAY
<br />EXIT L164T (ARROW INDICATES DIRECTION)
<br />-7. ALL WORK SHALL BE PERFORMED DURING TIME PERIOD5 ACCEPTABLE
<br />HAVE BEEN DAMAGED THEREBY.
<br />TO THE OWNER. SCHEDULE ALL WORK WITH THE OIWNER'5 AUTHORIZED
<br />T
<br />ALL REQUIRED INSURANCE TO BE PROVIDED FOR PROTECTION AGAINST PUBLIC LIABILITY OF
<br />8. CONTRACTOR SHALL V151T THE JOB 51TE AND BE 'THOROUGHLY FAMILIAR
<br />PROPERTY DAMAGE FOR THE DURATION OF THE WORK.
<br />WITH EXISTING CONDITIONS UNDER WHIGH THE WORK MUST BE PERFORMED.
<br />5.
<br />CONTRACTOR TO PAY FOR ALL PERMITS, FEES, INSPECTIONS AND TESTING.
<br />CONDUCTORS AS SHOWN ON PANEL SCHEDULE U.D.
<br />.N
<br />q.
<br />ELECTRICAL INSTALLATION TO MEET ALL STANDARD REQUIREMENTS OF LOCAL POWER AND
<br />TRACK LIGHTING
<br />4
<br />TELEPHONE COMPANIES.
<br />10. MINIMUM WIRE SIZE SHALL BE #12 AWG, EXCLUDING CONTROL WIRING. UNLE55 OTHERWISE NOTED,
<br />CONDUCTORS SHALL BE COPPER WITH THWN/THHN INSULATION. CONDUCTORS #12 AND SMALLER
<br />MAY BE SOLID; ALL THOSE #10 AND LARGER TO BE STRANDED.
<br />II. ALL UNDERGROUND RAGEWAY5 SHALL BE GALVANIZED RIGID STEEL CONDUIT OR SCHEDULE 40
<br />PVC. ALL OTHER RAGEWAY5 TO COMPLY WITH GOVERNING CODES. MINIMUM CONDUIT
<br />UNDERGROUND SHALL BE 3/4" CONDUIT UNLESS OTHERWI5E NOTED.
<br />12. OUTLET 'BOXE5 SHALL BE PRE55ED STEEL IN DRY LOCATIONS, CAST ALLOY WITH THREADED
<br />HUB5 IN WET OR DAMP LOCATIONS, AND BE OF SPECIAL CONSTRUCTION FOR OTHER GLA551FIED
<br />AREAS. ALL BOXES SHALL BE RECESSED (FLUSH) IN WALLS OR CEILING5 WHENEVER POSSIBLE.
<br />13. DISCONNECT SWITCHES SHALL BE H.P. RATED, GENERAL DUTY, QUICK -MAKE, QUICK -BREAK TYPE,
<br />ENCLOSURES SHALL BE AS REQUIRED BY N,E.G. AND LOCATION (WEATHERPROOF, EXPLOSION -
<br />PROOF, ETC.).
<br />14. ALL GENERAL PURPOSE SWITCHES AND RECEPTACLES SHALL BE THE PRODUCT OF A SINGLE
<br />MANUFACTURER. LEVITON, HUBBELL, PASS d SEYMOUR, OR ARROW HART WILL BE ACCEPTED.
<br />DEVICE TYPES AND COLOR SHALL MATCH BUILDING STANDARD.
<br />15. ALL RACEWAYS AND PIPES, SPACED IN OR THROUGH ANY CONCRETE SLAB, SHALL BE 5PAGED
<br />A MINIMUM OF THREE TIMES THE DIAMETER OF THE LARGEST RAGEWAY.
<br />16. IT 15 NOT THE INTENT OF THESE PLANS TO SHOW EVERY MINOR DETAIL OF CONSTRUCTION. THE
<br />GONTRAGTOR IS EXPECTED TO FURNI5H AND INSTALL ALL ITEMS FOR A COMPLETE ELECTRICAL
<br />SYSTEM, AND PROVIDE ALL NEGE55ARY DEVICES AND COMPONENTS FOR EQUIPMENT TO BE
<br />PLACED IN PROPER WORKING ORDER,
<br />17. ALL ELECTRICAL RAGEWAY5 (METALLIC AND NONMETALLIC) SHALL HAVE AN EQUIPMENT
<br />GROUND CONDUCTOR 51ZED IN ACCORDANCE WITH THE LATEST EDITION OF THE N.E.G.
<br />15. LOAD DATA 15 BASED ON INFORMATION GIVEN ENGINEER AT THE TIME OF DESIGN. VERIFY ALL
<br />EQUIPMENT NAMEPLATE RATINGS BEFORE ORDERING.
<br />Iq. CIRCUITS SHOWN ON PLANS ARE TO DETERMINE LOAD UATA AND PANEL SIZES. THE
<br />GONTRACTOR IS TO PROVIDE CIRCUITS AND ROUTING OF CONDUITS TO SUIT JOB CONDITIONS.
<br />20. TANDEM AND HALF -SPACE CIRCUIT BREAKERS SHALL NOT BE USED.
<br />21. ALL UNDERGROUND PVG CONDUIT RUNS SHALL HAVE RiO19 STEEL ELBOW5 AND RIGID STEEL
<br />SECTIONS AT SLAB PENETRATIONS. WHERE RIGID STEEL 6 USED, IT SHALL BE COMPLETELY
<br />COATED WITH AN ALKALI AND RUST - RESISTANT BITUMA5TIG PAINT, AND THREADS SHALL BE
<br />COATED WITH ZING CHROMATE.
<br />22. ALL ELECTRICAL CONDUCTORS SHALL BE INSTALLED IN AN APPROVED RACEWAY.
<br />23. CONTRACTOR SHALL BE RESPONSIBLE FOR SEALING ALL CONDUIT PENETRATIONS MADE
<br />THROUGH FIRE RATED WALLS, CEILINGS, 5LAB5, ETC. PENETRATION SEALS SHALL Be PER U.L.
<br />ASSEMBLY STANDARDS.
<br />24. CONDUIT SYSTEM REQUIREMENTS:
<br />UNDERGROUND - PVG WITH RIGID qO THROUGH SLAB.
<br />ABOVE FIN15H FLOOR, CEILINGS, ETC. (INDOOR) - EMT WITH DIECA5T SET 5CREW FITTINGS.
<br />GALVANIZED RIGID CONDUITS - ABOVE GRADE AND WHERE SUSCEPTIBLE TO PHYSICAL
<br />DAMAGE.
<br />FLEXIBLE CONDUITS - INDOOR, ONLY SHORT RUNS NOT TO EXCEED 6-0 ".
<br />5EALTITE - OUTDOOR, ONLY SHORT RUNS NOT TO EXCEED 6-0 ".
<br />25. CONDUCTOR COLOR CODING:
<br />THE FOLLOWING APPLICABLE COLOR CODES SHALL BE IMPLEMENTED AND P05TED IN ALL
<br />PANELS, DISCONNECT 5WITGHE5, ETC., PER NEC ARTICLEE5 200.6(D) AND 215.12:
<br />120 1205\1., 3 -PH.
<br />PHASE 'A' BLACK
<br />PHASE 'B' RED
<br />PHASE 'G' BLUE
<br />NEUTRAL WHITE
<br />GROUND GREEN
<br />ISOL. GROUND GREEN/YELLOW
<br />+ MG GABLE: METAL -GLAD GABLE
<br />• FOR ALL CIRCUITS; GABLE SHALL BE 'HEALTH GARS
<br />FACILITY METAL GLAD GABLE' TYPE (HGF) ONLY, IN
<br />COMPLIANCE WITH NEG 51-7.13 (A)(B).
<br />• FOR ALL LIGHTING CIRCUITS ABOVE 8'-0" ONLY;
<br />GABLE MAY BE 'METAL GLAD GABLE' TYPE (MG).
<br />• HOME RUNS SHALL REMAIN IN CONDUITS.
<br />• MG GABLE MAY BE USED FOR 20 AMP CIRCUITS IN
<br />WALLS OR ABOVE AGGE551BLE CEILINGS.
<br />• FOR ALL LIGHTING CONTROL SWITCHES, GABLE
<br />SHALL BE 'HEALTH CARE FACILITY METAL GLAD
<br />GABLE' TYPE (HGF) ONLY, IN COMPLIANCE WITH NEG
<br />51 -7.13 (A)(B).
<br />Ng E3
<br />• MG GABLE WIRE 0AUGE5 SHALL BE AS 5HOWN ON
<br />PANEL SCHEDULE.
<br />• MG GABLE SHALL ONLY BE USED WHERE ALLOWED
<br />BY N.E.G. 5EGTION 330.10 AND /OR AS 5HOWN
<br />ABOVE, WHIGHEVER IS MORE STRINGENT.
<br />• WHERE ALLOWED, MG GABLE SHALL BE INSTALLED
<br />PER N.E.G. 330.
<br />• MG GABLE MAY NOT BE U5ED IN OPEN STRUCTURE
<br />AREA.
<br />Na3A
<br />DEMOLITION NOTE5
<br />v
<br />I, ELECTRICAL PLANS DO NOT INCLUDE A DEMOLITION PLAN FOR THE
<br />L
<br />RENOVATED AREAS. CONTRACTOR SHALL REVIEW THESE PLANS AND
<br />E
<br />COORDINATE WITH THE GENERAL CONTRACTOR ON SITE TO THE
<br />N
<br />DETERMINE THE EXTENT OF THE DEMOLITION WORK AND PROJECT
<br />N
<br />PHASING REQUIRED AND PROVIDE ACCORDINGLY. ALL ELECTRICAL
<br />REVIEW
<br />DEMOLITION WORK SHALL BE PART OF THE ELECTRICAL
<br />L
<br />CONTRACTOR'S WORK.
<br />ALTERED WITHOUT WRITTEN AUTHORIZATION.
<br />WIRING DEVICES.
<br />ITEMS WHIGH APPLY TO TH15 PROJECT.
<br />2. ELECTRICAL DEMOLITION WORK SHALL INCLUDE, MT NOT BE LIMITED TO,
<br />A
<br />REMOVING, RECEPTACLES, WIRE, CONDUIT, ETC., AS REQUIRED FOR THE
<br />L
<br />INSTALLATION OF NEW EQUIPMENT AS INDICATED ON THE PLANS.
<br />L
<br />3. CONTRACTOR SHALL REMOVE ANY EXPOSED WIRE, CONDUIT, HANGERS,
<br />FLUORESCENT L16HT FIXTURE, LETTER INDICATE-5 TYPE
<br />CLAMPS, ETC., WHIGH ARE NOT BEING UTILIZED FOIR THE NEW
<br />MAIN 5WITGH113OARD
<br />INSTALLATION.
<br />Og
<br />4. EXISTING WIRE AND CONDUITS CONGEALED ABOVE: CEILING OR IN WALL5
<br />MDP
<br />AND NOT BEING REUSED SHALL BE REMOVED. EX15TINO CONDUITS,
<br />T
<br />WHERE APPLICABLE, MAY BE REUSED.
<br />WALL BRACKET LIGHT FIXTURE, LETTER INDICATES TYPE
<br />5. REV15E ALL EX15TINO PANEL DIRECTORIES TO REFLECT ALL REVI5ION5.
<br />KEYNOTES
<br />6. THE CONTRACTOR SHALL PROVIDE RUBBER MATS AND PLYWOOD
<br />® ®NL
<br />COVERS TO ALL OWNER'S EQUIPMENT 505CEPTI13LE TO DAMAGE DURING
<br />CONSTRUCTION. VERIFY SPECIFIC LOCATIONS WITH OWNER'S AUTHORIZED
<br />Q
<br />REPRESENTATIVE.
<br />EXIT L164T (ARROW INDICATES DIRECTION)
<br />-7. ALL WORK SHALL BE PERFORMED DURING TIME PERIOD5 ACCEPTABLE
<br />AS SHOWN ON PANEL 56HEDULE. U.O.N.
<br />TO THE OWNER. SCHEDULE ALL WORK WITH THE OIWNER'5 AUTHORIZED
<br />O
<br />REPRESENTATIVE 48 HOURS BEFORE PROGEEDINa.
<br />8. CONTRACTOR SHALL V151T THE JOB 51TE AND BE 'THOROUGHLY FAMILIAR
<br />G
<br />WITH EXISTING CONDITIONS UNDER WHIGH THE WORK MUST BE PERFORMED.
<br />J �
<br />THESE NOTES APPLY TO ALL ELEGTRIGAL SHEETS.
<br />N,5A
<br />NOTE5
<br />v
<br />LEO END
<br />I6
<br />I. THE CONTRACTOR SHALL REMOVE ALL EXISTING WIRING AND EQUIPMENT
<br />E
<br />MADE UNNECESSARY BY THE RENOVATION. ALL MATERIALS REMOVED
<br />MOUNTING HEIGHTS 5HOWN ARE MAXIMUM/MINIMUM
<br />SHALL BE 015POSED OF BY THE CONTRACTOR.
<br />N
<br />AGGES5IBILITY 5TANDARD5 - THEY SHALL
<br />REVIEW
<br />2. CONTRACTOR SHALL VERIFY WITH VARIAN INSTALLER FOR COORDINATION
<br />L
<br />OF MOUNTING HEIGHT5 AND /OR LOCATIONS OF ALL NEW OUTLETS AND
<br />ALTERED WITHOUT WRITTEN AUTHORIZATION.
<br />WIRING DEVICES.
<br />ITEMS WHIGH APPLY TO TH15 PROJECT.
<br />E
<br />A
<br />3. ALL TELEPHONE/DATA JACKS AND GABLING TO BE PROVIDED AND
<br />INSTALLED
<br />BY OWNER'S VENDOR.
<br />L
<br />4. GROUND CONDUCTOR SHALL BE INSTALLED IN ENTIRE RAGEWAY SYSTEM.
<br />FLUORESCENT L16HT FIXTURE, LETTER INDICATE-5 TYPE
<br />5. REUSE EXISTING JUNCTION BOXES, CONDUIT AND WIRING WHERE
<br />MAIN 5WITGH113OARD
<br />APPLICABLE. REMOVE AND DISPOSE OF ALL UNUSED CONDUIT AND
<br />Og
<br />WIRING BACK TO ITS SOURCE.
<br />MDP
<br />(b. ELECTRICAL CONTRACTOR SHALL VERIFY AND 000)RDINATE ALL DEVICE
<br />T
<br />TYPE5, LOCATIONS AND QUANTITIES WITH VARIAN REPRESENTATIVE AND
<br />WALL BRACKET LIGHT FIXTURE, LETTER INDICATES TYPE
<br />PROVIDE ACCORDINGLY.
<br />N24A
<br />NOTE5
<br />G
<br />IT IS THE CONTRACTOR'S RESPONSIBILITY TO REVIEW ALL DRANIN65
<br />O AND SPECIFICATIONS PRIOR TO 5UBMITTING A BID, REPORT ANY
<br />N D156REPANGIE5 TO ENGINEER PRIOR TO BID,
<br />BIDDERS ARE TO VISIT THE 51TE AND FAMILIARIZE THEM5ELVE5 WITH
<br />T EXISTING CONDITIONS AND SATISFY THEM5ELVE5 AS TO THE NATURE AND
<br />SCOPE OF THE WORK. THE SUBMISSION OF A BID WILL BE EVIDENCE THAT
<br />R 5UGH AN EXAMINATION HAS BEEN MADE. LATER CLAIMS FOR LABOR,
<br />AEQUIPMENT, OR MATERIALS REQUIRED, OR FOR ANY DIFFICULTIES
<br />ENCOUNTERED WHIGH GOULD HAVE BEEN FORESEEN HAD AN EXAMINATION
<br />G BEEN MADE, WILL NOT BE ALLOWED.
<br />IT 15 THE RE5PON51BILITY OF THE CONTRACTOR TO NOTIFY THE ENGINEER
<br />T OF ANY DISCREPANCIES ENCOUNTERED ON THE PLANS OR IN EX15TINO SITE
<br />O GONDITIONS PRIOR TO 5013M15510N OF BID,
<br />ALL EXISTING GIRGUIT5 TO REMAIN SHALL BE RECONNECTED WHETHER
<br />INDICATED OR NOT ON PROJECT DOCUMENT5,
<br />NEW AND EXISTING CIRCUIT DE5IGNATION5 MAY NOT REPRESENT ACTUAL
<br />FIELD CONDITIONS. THEY ARE INTENDED FOR REFERENCE ONLY.
<br />GONTRACTOR SHALL COORDINATE WITH OTHER TRADES IN REGARDS TO
<br />THEIR 56OPE OF WORK WHIGH WILL REQUIRE ELEGTRIGAL WORK SUCH AS
<br />DISCONNECTION AND /OR RECONNECTION OF EQUIPMENT, AND WHICH MAY
<br />NOT BE 5HOWN OR INDICATED ON THE DRAWINGS.
<br />THESE NOTES APPLY TO ALL ELECTRICAL 5HEI✓T5.
<br />N3A
<br />■
<br />® FLOOR MOUNTED TELEPHONE RECEPTACLE DEVICE AS NOTED
<br />E..: TELEPHONE BACKBOARD WITH #6 U. GROUND (SIZE AS NOTED)
<br />K
<br />E6
<br />EQUIPMENT GROUND
<br />LEO END
<br />I6
<br />E
<br />FJF -EF
<br />NOT ALL DEVIGE5 5HOWN IN LEGEND ARE REQUIRED.
<br />MOUNTING HEIGHTS 5HOWN ARE MAXIMUM/MINIMUM
<br />L
<br />HANDICAPPED
<br />AGGES5IBILITY 5TANDARD5 - THEY SHALL
<br />REVIEW
<br />POWER 4 LIGHTING PLANS AND DETAILS
<br />ELECTRIC WATER HEATER
<br />NOT BE
<br />ALTERED WITHOUT WRITTEN AUTHORIZATION.
<br />FOR
<br />ITEMS WHIGH APPLY TO TH15 PROJECT.
<br />E
<br />Of
<br />®
<br />FLUORESCENT L16HT FIXTURE, LETTER INDICATE-5 TYPE
<br />M58
<br />MAIN 5WITGH113OARD
<br />G
<br />Og
<br />INCANDESCENT OR HID LIGHT FIXTURE, LETTER INDICATES TYPE
<br />MDP
<br />MAIN D15TRIBUTION PANEL
<br />T
<br />I-O C,
<br />WALL BRACKET LIGHT FIXTURE, LETTER INDICATES TYPE
<br />O
<br />KEYNOTES
<br />® ®NL
<br />LIGHT FIXTURE ON EMERGENCY CIRCUIT/NIGHT LIGHT NU
<br />CONDUIT CONCEALED IN WALL OR ABOVE CEILING WITH CONDUCTORS
<br />Q
<br />®
<br />EXIT L164T (ARROW INDICATES DIRECTION)
<br />V
<br />AS SHOWN ON PANEL 56HEDULE. U.O.N.
<br />J
<br />O
<br />BATTERY POWERED EMERGENCY LIGHT
<br />CONDUIT CONCEALED BELOW FLOOR SLAB OR FINISHED GRA WI
<br />DE TH
<br />G
<br />Q
<br />J �
<br />CONDUCTORS AS SHOWN ON PANEL SCHEDULE U.D.
<br />.N
<br />4��
<br />TRACK LIGHTING
<br />4
<br />CONDUIT EXPOSED ON WALL OR CEILING WITH GONDUGTOR5 A5 SHOM
<br />ON PANEL `SCHEDULE. U.O.N.
<br />T
<br />Q
<br />51NGLE POLE SWITCH, LOWER CASE LETTER INDICATES L16HT
<br />TV
<br />0
<br />L
<br />CONTROLLED, MOUNT 46' A.F.F. U.O.N.
<br />TELEVISION SYSTEM EMPTY CONDUIT WITH PULL WIRE
<br />52
<br />DOUBLE POLE SWITCH, MOUNT 48" A.FF. U.O.N.
<br />FLEXIBLE CONDUIT NOT TO EXCEED 6 FEET IN LENGTH
<br />Z
<br />W
<br />53
<br />THREE -WAY 5WITCH, MOUNT 48' AF.F. U.O.N,
<br />/DC,
<br />D.G. VOLTAGE WIRING (#10 WIRE IN I/2' CONDUIT)
<br />54
<br />FOUR -WAY SWITCH, MOUNT 46' A.F.F. U.O.N.
<br />�=I
<br />HUREMOLD (SIZE AND LENGTH AS NOTED)
<br />5P
<br />51N6LE POLE 5WITCH WITH PILOT LIGHT, MOUNT 48" A.F.F. U.O.N.
<br />CONDUIT 5EAL -OFF FITTING
<br />5K
<br />KEY OPERATED SINGLE POLE SWITCH, MOUNT 48' A.F.F. UO.N.
<br />PADDLE FAN WITH BACKBOX CAPABLE OF SUPPORTTN6 100 LB. LOAD
<br />5F
<br />FAN CONTROLLER, MOUNT 46" A.F.F. U.O.N.
<br />o�
<br />®
<br />DIMMER 5WITCH, WATT5 AS NOTED, MOUNT 48" A.F.F. U.UN.
<br />D4
<br />T.V. CAMERA
<br />9H
<br />MOTOR RATED SWITCH
<br />©
<br />T.V. MONITOR
<br />8-
<br />51NGLE RECEPTACLE, AMPS AS NOTED, MOUNT 18" A.F.F. U.O.N.
<br />TELEVISION OUTLET, PROVIDE SINGLE 6AN6 BOX WITH 3/4' CONDUIT
<br />Om
<br />DUPLEX RECEPTACLE, MOUNT 18' A.F.F. U,ON
<br />HSI
<br />WITH PULL WIRE AND INSU.-ATTNG BUSHING STUBBED INTO CEILING
<br />SPACE. MOUNT BOX 18' A.F.F. U.O.N.
<br />DUPLEX RECEPTACLE, MOUNT ABOVE COUNTER HEIGHT U,O.N.
<br />QUADRAPLEX RECEPTACLE, MOUNT 18' A.F.F, U.O.N.
<br />`fl
<br />D15CONNEGT 5WIT6H
<br />DUPLEX RECEPTACLE, ONE HALF SWITCHED, MOUNT 18" A.F.F. U.O.N.
<br />10013160
<br />DISCONNECT DESIGNATION (51ZE/POLES/FUSE) 'NF' INDICATES
<br />NON-FUSED; "DE' INDICATES DUAL ELEMENT FUSES.
<br />30A
<br />I PH, 250V, RECEPTACLE, AMPS AS NOTED, MOUNT 18' A.F.F. UD N
<br />®
<br />MA6NETIG MOTOR STARTER
<br />SPECIAL RECEPTACLE AS NOTED
<br />`z
<br />COMBINATION MAGNETIC MOTOR STARTER/01SCONNECT SWITCH
<br />Q
<br />FLOOR MOUNTED DUPLEX RECEPTACLE
<br />Q
<br />DRY TYPE TRANSFORMER
<br />eFl
<br />6ROUND FAULT INTERRUPTER RECEPTACLE, LEVITON 068g8 -1, MO,lNT
<br />17-
<br />CONTACTOR (A5 NOTED)
<br />ABOVE COUNTER HEIGHT U.ON
<br />�B•
<br />DUPLEX RECEPTACLE, ISOLATED GROUND TYPE, LEVITON #5362 -161
<br />HI
<br />TIME CLOCK
<br />MOUNT AT 16" A.F.F. U.O.N.
<br />P,c
<br />PHOTO -CELL
<br />DUPLEX RECEPTACLE, SPLIT WIRED, MOUNT 18' A.F.F. U.O.N.
<br />MOTOR PERMANENTLY CONNECTED WITH FLEXIBLE CONDUIT
<br />I�
<br />CRT OUTLET, PROVIDE SINGLE GANG BOX WITH 3/4" 00NOUITWITI4
<br />FULL WIRE AND
<br />°
<br />INSULATING BUSHING STUBBED INTO CEILING SPACE.
<br />®
<br />ELECTRIC DUCT HEATER
<br />MOUNT BOX 18" A.F.F. U.O.N.
<br />®
<br />2T1/4WV, 30 PANELBOARD
<br />TO
<br />THERMOSTAT. PROVIDE SINGLE 6AN6 BOX WITH 112' G. STUBBED
<br />INTO CEILING SPACE, MOUNT 60" A.F.F. U.C.N. (COORDINATE WITH
<br />L16HTIN(9 OR POWER PANELBOARD
<br />MECHANICAL DRA 4IN65 PRIOR TO ROUGH -IN)
<br />0
<br />TELEPHONE WALL OUTLET, PROVIDE 51NGLE 6AN6 BOX WITH 314'
<br />P1)5HBUTTON, MOUNT 48' A.F,F. U,O.N.
<br />CONDUIT WITH PULL WIRE AND INSULATING BUSHING 5TUeeED INTO'
<br />CEILING SPACE. MOUNT BOX 18' A.F.F. U.O.N.
<br />DOOR CHIME WITH TRAN51FORMER
<br />.
<br />TELEPHONE WALL OUTLET, PROVIDE SINGLE GANG BOX WITH 3/4"
<br />05
<br />SPEAKER
<br />CONDUIT WITH FULL WIRE AND INSULATING BUSHING 5TUBBE9 INTO
<br />CEILING SPACE. MOUNT BOX ABOVE COUNTER, U.ON.
<br />JO
<br />,JtRJGTION BOX (FLUSH MOUNT IN FINISHED AREAS U.ONJ
<br />■
<br />® FLOOR MOUNTED TELEPHONE RECEPTACLE DEVICE AS NOTED
<br />E..: TELEPHONE BACKBOARD WITH #6 U. GROUND (SIZE AS NOTED)
<br />K
<br />E6
<br />EQUIPMENT GROUND
<br />EWC
<br />I6
<br />150LATED GROUND
<br />FJF -EF
<br />HP
<br />WEATHERPROOF
<br />A/H -AHU
<br />EC
<br />EMPTY CONDUIT
<br />ACG -OU
<br />EWH
<br />ELECTRIC WATER HEATER
<br />RTU
<br />:0 0 �i►r,
<br />ELECTRIC WATER COOLER
<br />NL
<br />EXHAUST FAN
<br />PC
<br />AIR HANDLING UNIT
<br />C/f
<br />CONDEN51 NG UNIT
<br />EX
<br />ROOF TOP UNIT
<br />AFF
<br />N16HT L16HT
<br />PULL CHAIN
<br />CURRENT TRANSFORMER
<br />EXI5TIN6 DEVICE
<br />ABOVE FINISH FLOOR
<br />NOTE MOUNTING HEIGHT5 NOTED ARE TO TOP LINE OF DEVICE SNOHN U.O.N.
<br />AF&
<br />ABOVE FINISH GRADE
<br />U.O.N.
<br />UNLESS OTHERVII5E NOTED
<br />N.T.5.
<br />NOT TO 5GALE
<br />WG
<br />NOT IN CONTRACT
<br />Issued for:
<br />Date;
<br />❑ PRELIMINARY
<br />❑ PRICING
<br />❑ BIDDING
<br />■ PERMIT
<br />07-23 -13
<br />❑ CONSTRUCTION
<br />W
<br />NOW
<br />00 00
<br />Of
<br />Z
<br />0
<br />w
<br />0
<br />r�
<br />v
<br />y
<br />m
<br />>-
<br />O
<br />Q
<br />V
<br />0
<br />J
<br />O
<br />q
<br />Q
<br />J �
<br />W
<br />4
<br />U
<br />U
<br />T
<br />oa
<br />z
<br />Q
<br />0
<br />M
<br />M
<br />Z
<br />W
<br />U-)
<br />�
<br />z
<br />U
<br />� �
<br />Issued for:
<br />Date;
<br />❑ PRELIMINARY
<br />❑ PRICING
<br />❑ BIDDING
<br />■ PERMIT
<br />07-23 -13
<br />❑ CONSTRUCTION
<br />W
<br />f Seal
<br />1'
<br />1EILS CH A E
<br />:N5f� .49 21
<br />Project No.:
<br />1'3-106_
<br />Drawing No:
<br />E -1
<br />lDrawn by. T.M. Checked py: S.C. i
<br />co
<br />N
<br />ti
<br />O
<br />W
<br />D
<br />co
<br />co
<br />,W
<br />VI
<br />W
<br />a
<br />W
<br />W
<br />NOW
<br />0��-
<br />Z
<br />0
<br />0
<br />Q
<br />V)
<br />V
<br />J
<br />O
<br />q
<br />Q
<br />�WU
<br />W
<br />z
<br />°
<br />U
<br />U
<br />:b
<br />oa
<br />Q
<br />M
<br />Z
<br />W
<br />�
<br />z
<br />J
<br />o�
<br />f Seal
<br />1'
<br />1EILS CH A E
<br />:N5f� .49 21
<br />Project No.:
<br />1'3-106_
<br />Drawing No:
<br />E -1
<br />lDrawn by. T.M. Checked py: S.C. i
<br />co
<br />N
<br />ti
<br />O
<br />W
<br />D
<br />co
<br />co
<br />,W
<br />VI
<br />W
<br />a
<br />
|