13-14731 - Laserfiche WebLink

Browse Search

SpectrAlert Advance Specifications .- . General SpectrAlert Advance strobes and horn strobes shall mount to a standard 4 x 4 x 1'/z-inch back box,4-inch octagon back box,or double- gang back box.Two-wire products shall also mount to a single-gang 2 x 4 x 17B-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate.Also,SpectrAlert Advance products,when used with the Sync•Circuit'"Module accessory,shali be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module,12-voit-rated notification appliance circuit outputs shall operate between 9 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall opera[e between 17 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectitied unfiitered power supply.Strobes and horn strobes shall have field-selectable candela settings including 15. 15175,30,75,95. 110, 115,135, 150, 177,and 185. Strobe The strobe shail be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective serwce. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/retlector system. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lenslreflector system.The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.On four-wire products,the strobe shall be powered independently of the sounder.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync•Circuit model MDL listed to UL 464 and shail be approved for fire protective service.The module shali synchron¢e SpectrAlert strobes at 1 Hz and homs at temporal three.Also,while operating the strobes the module shali siience the horns on hom strobe models over a single pair of wires.The module shall mount to a 411/16 x 411/16 x 21B-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power suppiy. Standard Operating Tempewature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Fiash Rate 1 flash per second Nomina!Voltage Regulated 12 DC/FWR or regulated 24 DClFWR' Operating Voitage Range2 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) InputTerminal Wire Gauge 12 to 18 AWG Ceiling-Mount Dimensions(including lens) 6.8 diameter x 2.5"h�gh(173 mm diameter x 64 mm high) Ceiling-Mount Back Box Skirt Dimensions(BBSC-2,BBSCW-2) 7 1 diameter x 2.2""high(180 mm diameter x 57 mm high) Ceiling-MountTrim Ring Dimensions(soid as a 5 pack)(TRC-HS, 6.9""diameter x 0.35"high(175 mm diameter x 9 mm high) TRCW-HS) Notes: t Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.P,S,PC,and SC products will operate at 12 V nominal only for 15 and 15/75 cd. nvcsooso,