13-14731 - Laserfiche WebLink

Browse Search

SpectrAlert Advance Outdoor Horn,Strobe,and Horn Strobe Specifications .• . General SpectrAlert Advance outdoor horns,s[robes,and horn strobes shall mount to a weatherproof back box.A universal mounting piate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate. Also,SpectrAlert Advance products,when used with the Sync•Circuit'"Module accessory,shail be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module,12-volt-rated notification appliance circuit outputs shall operate between 9 and 17.5 volts;24-volt-rated notification appliance circwt outputs shall operate between 17 and 33 volts.Outdoor SpectrAlert Advance products shall operate between-40 and 151 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply.Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75,30,75,95, 110, 115, 135, 150, 177,and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shali be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe Iight shall consist of a xenon flash tube and associated lens/reflector system.The strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL.The strobe shall be suitable for use in wet environments. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shali be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appl�ance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lenslreflector system.The horn shall have three audibility options and an option to switch between a temporai three pattern and a non-temporal(continuous)pattern.These options shall be set by a multiple position switch. On four-wire products,the strobe shall be powered independently of the sounder.The horn or horn strobe models shall operate on a coded or non-coded power supply.The horn strobe must be mstalled wdh ds weatherproof back box in order to remain outdoor approved per UL The horn strobe shall be suitable for use in wet environments. .- . Operating Temperature -40°F to 151°F(-40°C to 66°C) Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR' Operating Voitage Range2 8 to 17.5 V(12 V nomina�)or 16 to 33 V(24 V nominal) input Terminal Wire Gauge 12 to 18 AWG Wali-Mount Dimensions(including lens) 5.6"L x 4 7"'W x 2.5 D(142 mm L x 119 mm W x 64 mm D) Horn Dimensions 5.6"�x 4 7""W x 1.3"D(142 mm L x 119 mm W x 33 mm D) Wall-Mount Weatherproof Back Box Dimensions(SA-WBB) 5.7°L x 5.1"W x 2.0 D(145 mm L x 130 mm W x 51 mm D) Notes: 1 Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.P,S,PC,and SC products wiil operate at 12 V nominal only for 15 and 15/75 cd. nvoso,z�,