14-15034 - Laserfiche WebLink

Browse Search

• Float-charge voltage: 27.6 VDC. Standards and Codes • Maximum current charge: 1.5 A. The FCPS-24S6 and FCPS-24S8 comply with the following • Maximum battery capacity: 18 AH. standards: • • NFPA 72 National Fire Alarm Code. Applications • UL 864 Standard for Control Units for Fire Alarm Systems Example 1: Expand notification appliance power an additional (NAC expander mode). , 6.0 A (FCPS-24S6) or 8.0 A (FCPS-24S8). Use up to four . UL 1481 Power Supplies for Fire Alarm Systems. Class B (Style Y) outputs or four Class A (Style Z) outputs (using ZNAC-4). For example, the FACP notification appliance A9ency Listings and Approvals circuits will activate the FCPS when reverse-polariiy activation occurs. Trouble conditions on the FCPS are sensed by the These listings and approvals apply to the modules specified in FACP through the notification appliance circuit. this document. In some cases,certain modules or applications Example 2: Use the FCPS to expand auxiliary regulated 24- may not be iisted by certain approval agencies, or listing may volt system power up to 4.0 A (FCPS-24S6) or up to 6.0 A be in process. Consult factory for latest listing status. (FCPS-24S8). Both resettable and non-resettable power • UL Listed: S635,S674 options are available. Resettable outputs are created by con- . ULC Listed:S635(FCPS-24S6C&FCPS-24S8C) necting the resettable output from the FACP to one or both of � CSFM Approved: 7315-0028:225 the FCPS inputs. Example 3: Use addressable control modules to activate the � MEA: 299-02-E FCPS instead of activating it through the FACP notification ' FM Approved appliance circuits.This typicaliy allows for mounting the FCPS at greater distances' away from the FACP while expanding Ordering Information system architecture in various appiications. FCPS-24S6: 6.0 A, 120 VAC remote charger power supply. For example, an addressable control module is used to acti- Includes main printed circuit board, transformers, enclosure vate the FCPS, and an addressable monitor module is used to (15"H x 14.5"W x 2.75"D[cm:38.1 H x 36.83W x 6.985D]),and sense FCPS trouble conditions. Local auxiliary power output installation instructions. from the FCPS provides power to the addressable control FCPS-24S6C: Same as above, ULC-listed. module. 'NOTE:Addressable FACPs are capable of locatrng control and FCPS-24S6R: Same as FCPS-24S6 with red enclosure. monitor modules at distances of up to 12,500 feet(3,810 meters). FCPS-24S6E: 6.0 A, 240 VAC remote charger power supply. Includes main printed circuit board, transformers, enclosure Sync Follower/Generator Note (15"H x 14.5"W x 2.75"D[cm:38.1 H x 36.83W x 6.985D]),and installation instructions. In some installations, it is necessary to synchronize the flash timing of all strobes in the system for ADA compliance. FCPS-24S8: 8.0 A, 120 VAC remote charger power supply. Strobes accomplish this by monitoring very short timing pulses Inciudes main printed circuit board, transformers, enclosure on the NAC power which are created by the FACP. When (15"H x 14.5"W x 2.75"D[cm:38.1H x 36.83W x 6.985D]),and installed at the end of a NAC wire run, the FCPS-24S6/-24S8 installation instructions. can track (i.e. "follow") the strobe synchronization timing FCPS-24S8C Same as above, ULC-listed. puises on the existing NAC wire run.This maintains the overall FCPS-24S8R: Same as FCPS-24S8 with red enclosure. system flash timing of the additional strobes attaches to the FCPS. <FCPS-24S8E: 8.0 A, 240 VAC remote charger power supply. � When the FCPS-24S6/-24S8 is configured(via DIP switch set- Includes main printed circuit board, transformers, enclosure S tings) as a "sync follower," the FCPS's NAC outputs track the `��5"H x 14.5"W x 2.75'D[cm:38.1 H x 36.83W x 6.985D]),and R strobe synchronization pulses present at the FCPS's sync �installation instructions. � � P input terminal.The pu�ses originate from an upstream FACP or ZNAC-4: Class A(Style Y)NAC option module. other power supply. EOLR-1: 12/24 VDC end-of-line relay for monitoring four-wire When the FCPS-24S6/-24S8 are configured (via DIP switch smoke detector power. settings) as a "sync generator," the FCPS's sync input termi- gAT 1270: Battery, 12-volt, 7.0 AH (two required, see BAT nals are not used. Rather, the FCPS is the originator of the Series data sheet DN-6933). strobe synchronization puises on the FCPS's NAC outputs. In "sync generator'mode,the sync type (System Sensor, Whee- lock,or Gentex)is selectable via DIP switch settings. System Sensor�and NOTIFIERB are registered trademarks of Honeywell Internationalinc. 002013 by Honeywell International Inc.All rights reservetl.Unauthorized use of this document is s[rictty prohibited. '�� This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. � ��a�� Ali specifications are subject to change without notice. � QOALITr S�STEMS MadeinmeU.S.A. For more information,contact Notifier.Phone:(203)484-716�,FAX:(203)484-7��8. www.notifier.com Page 2 ot 2—DN-6927:A2•5/17/13