14-15318 - Laserfiche WebLink

Browse Search

� SpectrAt�rt�clv�nce�pecificatio�� i - , General SpectrAlert Advance horns,strobes,and horn strobes shall mount ta a standard 4 x 4 x 1�/-inch back box,4-inch octagon back box,or double-gang back box.Two-wire products shal!also mount to a single-gang 2 x 4 x 1718-inch back box.A unlversai maunting piate shall t�e used for mounting ceiling and wa11 products.The notificatian appliance circuit wiring sha(I terminate at the universal mounting p(ate. Also,SpectrAlert Advance products,when used with the Sync•CircuiY"Module accessory,shall be po�vered from a non-coded notification appliance circuit output and shal!operate on a nomina!12 or 24 volts.When used wiih tt,s Syne•Gircuit Module,12-volt-rated notification appiiance eircuit outputs shal(aperate between 8 and 17.5 volts;24-vait-rated notification appliance circuit outputs shal�operate between 16 and 33 volts.Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DG or full-wave rectified unfiitered poever supp}y Strabes and horn sirobes shail have field-selectabie candeia settings includ3ng 15,1517b,30,75,95,110, 115, 135. 150, 177,and�85. Strobe The strobe shaii be a System Sensor SpectrAlert Advance Madel listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for vlsibie signaling app(iances,flashing at 1 Hz over the strobe's entire operating voEtage range.The strobe light sna(1 consist af a xenon f(ash tube and associated lens/reflector system. Horn Strobe Cambination The horn strobe shall be a System Sensor SpectrAlert Advance Model listed ta UL 1971 and UL 464 and shall be approved for fire protective service.The harn strobe shall be wlred as a primary-signalir�g notificatian appliance and compiy with the Americans with Disabilities Act requirements#or visible signaling appliances,flashing at 1 Hz over the strobe's entire operaiing voltage range.The strobe light shall consist of a xenan flash tube and associated lenslreflector system.The horn shall have three audibility options and an option to switch between a temporal three pattem and a non-tempora!(continuous)pattern.These options are set by a multiple pasitit�n switch.On#aur-wire products,the strobe sha((be powered independently of the sounder.The hom on horn strobe models shail operate on a coded or non-coded power supply, . Synchronization Module The module shall be a System Sensar Sync•Circuit madel MC1L listed to UL 464 and shall be approved for fire protective service.The module sha0 synchronize SpectrAlert sirobes at 1 Hx and homs at temparal three.Also,whi[e operating ti�e strobes,the module shall silence the horns on horn strobe models over a singie pair of wires.The module shall mount to a 411/16 x 411/16 x 21/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize muitiple zones.Daisy chaining two or more synchronization moduies together wiEl syr�chro�ize all the zanes they car�trol.The madule shali not operate on a coded power supply. 3 Standard Operating Temperature 32°F io 120°F{d°C to 49°C} Humidity Range 10 to 93%nan-condensing Strobe F[ash Rate 1 flash per second Nominal Valtage Regulated 12 DC/FWR or regulated 24 DC/FWR' Operating Voltage h�angez 8 ta 17.5 V(i2 V nomir�a!}or 16 to 33 V{24 V�ominai} InputTerminat Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(inciuding lens) 5.6"L x 4 7"'W x 2.5"D(142 mm L x 119 mm W x 64 mm D) Horn Dimensians 5.6`�x 4 7`"W x 1.3"'D{142 mm L x 119 mm W x 33 mm D) Wall-Mount Back Bax Skirt Dimensipns(BBS-2,BBSW-2) 5.9"L.x 5.0"W x 2.2"'D(151 mm L x 128 mm W x 56 mm D) Wafl-MoecntTrim Riu�g Dimensians(sold as a 5 pactc}{TR-HS,i'RYV- 5.7"�x 4.8"W x 4.35"'D{145 mm L x 122 r�m W x 9 mm D) HS} Nates: 1.Fuli Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.P,S,PC,and SC products will operate at 12 V nominal only fpr 15 and 15/75 cd. .�V�500'o0t