Laserfiche WebLink
' ') <br /> ��� <br /> �`�..� TRINiI'Y I ERD <br /> 5.5 Allowable substrates are noted below: <br /> 5.5.1 Direct-Bond to Deck: <br /> Lastobond Shield, Lastobond Pro HT-IV Lastobond Shield HT or Lastobond Pro HT-S applied <br /> to: <br /> ➢ Plywood; <br /> ➢ ASTM D41 primed plywood; <br /> ➢ OSB; <br /> ➢ ASTM D41 primed OSB; <br /> ➢ Southern Yellow Pine; <br /> ➢ ASTM D41 primed Southern Yellow ine; <br /> ➢ ASTM D41 primed structural concre e. <br /> Lastobond TU HT, Lastobond, Lastobon 195, Lastobond ECO, Resisto L61236, Grip-Rite Eave <br /> &Valley Protector, Resisto LB1244 or L stobond Smooth Seal HT applied to: <br /> Y Plywood; <br /> ➢ ASTM D41 primed plywood; <br /> ➢ OSB; <br /> ➢ ASTM D41 primed OSB; <br /> ➢ ASTM D41 primed structural concre e. <br /> Colphene FR GR applied to: <br /> ➢ Plywood; <br /> ➢ ASTM D41 primed plywood; <br /> ➢ ASTM D41 primed structural concre e. <br /> Note: <br /> ➢ While not required over plywood, OSB or Southern Yellow Pine substrates, Soprema <br /> recommends priming with Elastoc l Stick or Elastocol 600c if the final roof cove� is not <br /> slated for installation within 24 hou s. <br /> ➢ Soprema requires tongue-and-groo e board decking be covered with plywood or OSB prior <br /> to installation of the self-adhering nderlayment. <br /> 5.5.2 Bond-to-Insulation: <br /> Lastobond TU HT, Lastobond Shield, La tobond Pro HT-N, Lastobond Shield HT, Lastobond Pro <br /> HT-S or Colphene FR GR applied to: <br /> ➢ DensDeck DuraGuard; <br /> ➢ DensDeck Prime; <br /> ➢ SECUROCK Gypsum-Fiber Roof Board. <br /> For installation under mechanically attached prepared roof coverings, insulation shall be <br /> attached per minimum requirements f the prepared roof covering manufacturer's Product <br /> Approval. For installations under f am-on tile systems, insulation attachment shall be <br /> designed by a qualified design p fessional and installed based on testing of the <br /> insulation/underlayment system in a cordance with FM 4474, Appendix D or TAS 114, <br /> Appendix J. <br /> 5.5.3 Bond to Mechanicall Attached Base La er: <br /> Lastobond Shield, Lastobond Pro HT-N Lastobond Shield HT, Lastobond Pro HT-S or Coiphene <br /> FR GR applied to: <br /> ➢ ASTM D226, Type I or II felt; <br /> ➢ Sopra-G; <br /> ➢ Modified Sopra-G. <br /> For installations under mechanically ttached prepared roof coverings, base layer shall be <br /> attached per minimum codified requir ments. For installations under foam-on tile systems, <br /> base layer shall be attached per minim m requirements of FRSA/TRI 07320/8-05 or RAS 120. <br /> Exterior Research and Design, LLC. Evaluation Report S18010.06.09-R5 <br /> Certifcate ofAuthoriaation#9503 FL2569-R7 <br /> Revision 5: 04/30/2014 <br /> Page 4 of 8 <br />