14-15344 - Laserfiche WebLink

Browse Search

i , I I SpectrAlert Advance Specifications General SpectrAlert Advance strobes and hom strobes shall mount to a sta dard 4 x 4 x 1�h-inch back bo�4inch octagon back box,or double-gang back box.Two- wire produds shall also mount to a single-gang 2 x 4 x 1�/a-inch ck box.A universal mounting plate shall be used for mounting ceiling and wall products The nolification appliance circuit wiring shall terminate at the uni rsal mounting plate.Also,SpectrAlert Advance produc[s,when used with the Sync•Cfrcuit" Module accessory,shall be powered from a non-coded notificatio appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module,l2-voit-rated notification appliance circui outputs shall operate between 9 and 17S vohs;24volt-2ted notification appliance circuit outpuu shall operate between 17 and 33 volts.Indoor SpectrAlert Advance produc[s shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply.Strobes and horn str bes shall have field-selectable candela settings including 15,15/75,30,75,95,110,115,135, 150,177,and 185. Strobe The svobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service.The strobe shall be wired as a primary-signaling notification appliance and comply wi h the Americans with Disabilities Act requfrements for visible signaling appliances,flashing at 1 Hz over the strobe's entlre operating voltage range.The strobe li ht shali consist of a xenon flash tube and associated lens/reflector system. Horn Strobe CombinaYion The hom svobe shall be a System Sensor Spec[rAlert Advance Mo el listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appli nce and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operatfng volta e range.The strobe light shall consist of a xenon Flash tube and associated lens/reflector system.The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.On four-wire produ ,the strobe shall be powered independently of the sounder.The hom on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Syno-Circuit model MDL list to UL 464 and shall be approved for fire protective service.The module shall rynchronize SpectrAlert strobes at 1 Hz and horns at temporal three.Also,whil operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 4"/,e x 4"/,b x 2'/ inch back box The module shall also control two StyleY(dass B)circuiu or one Sryle Z I (dass A)circuitThe module shall synchron¢e multiple zones.Dais chaining two or more synchronization modules together will synchronize all the zones they il control.The module shall not operate on a coded power supply. i Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93°,6 non-condensing Strobe Flash Rate 1 flash per second fdominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR� Operating Voltage RangeZ S to 175 V(12 V nominal)or 16 to 33 V(24 V nomfnal) Input Terminal Wire Gauge � 12 to 18 AWG ' Ceiling-Mount Dimensions(including lens) 6.8"diameter x2.5"high(173 mm diameter x 64 mm high) Ceiling-Mount Back Box Skirt Dimensions(BBSC-2,BBSCW-2) 7.1"diameter x 22"high(180 mm diameter x 57 mm high) Ceiling-MountTrim Ring Dimensions(sold as a 5 pack)(TRC- 5,TRCW-HS) 6.9"diameter x 035"high(175 mm diameter x 9 mm high) Notes: 1 Full Wave Rec[ified(FWR)voltage is a non-regulated,time-varyi g power source that is used on some power supply and panel outputs. 2.P,5,PC,and SC producu will operate at 12 V nominal only for 15 and 15/75 cd. AVD500500