|
3 5 � 8 ( ?,,jd (e- Wrn
<br />L_
<br />GENERAL CONSTRUCTION NOT5:
<br />CHAPTERS AND 5ECTION5 REFER TO F.B.CR - 6TH EDITION (2011). NOTE: ANY DIMEN51ON5 AND/OR CALLOUT5 WITHIN TH15 SET OF DRAWINGS REFERENCING LUMBER SIZES OR WALL THICKNE55 ARE
<br />TO BE CONSIDERED "NOMINAL DIMENSIONS". ALL DIMEN51ON5 ARE TO ROUGH FRAMING UNLE55 OTHERW15E NOTED.
<br />OCCUPANCY AND CONSTRUCTION TYPE:
<br />TH15 UNIT HAS AN R3 OCCUPANCY AND BUILDING TYPE v-B CLASSIFICATION.
<br />EXTERIOR WALL ENVELOPE:
<br />BUILDER 15 RE5PON51BLE FOR PROVIDING AND MEETING ALL REQUIREMENTS OF SECTION 1011.4 OF THE F.B.C.-BUILDING BY PROVIDING ALL DETAILS LISTED UNDER TH15 SECTION, INCLUDING BUT
<br />NOT LIMITED TO, THE MANUFACTURER'5 INSTALLATION IN5TRUCTION5 AND ALL 5UPPORTING DOCUMENTATION TO ENSURE THE WEATHER RE515TANCE OF THE EXTERIOR WALL ENVELOPE 15 MAINTAINED.
<br />CEILING CONSTRUCTION:
<br />THE GARAGE SHALL BE 5EPARATED FROM THE RESIDENCE AND ITS ATTIC AREA BY NOT LE55 THAN 112 INCH (12.1 mm) GYPSUM BOARD APPLIED TO THE GARAGE SIDE, GARAGES BENEATH
<br />HABITABLE ROOMS SHALL BE SEPARATED FROM ALL HABITABLE ROOMS ABOVE BY NOT LE55 THAN 5/8 INCH (15.5 mm) TYPE "X" GYPSUM BOARD OR EQUIVALENT. WHERE THE SEPARATION 6 A
<br />FLOOR=CEILING ASSEMBLY, THE STRUCTURE SUPPORTING THE SEPARATION SHALL AL50 BE PROTECTED BY NOT LE55 THAN 1/2 INCH (12.1 mm) GYPSUM BOARD OR EQUIVALENT IN ACCORDANCE WITH
<br />F.B.CR - 6TH EDITION (2011) R302b AND TABLE R302.6. ATTACHMENT OF GYPSUM BOARD SHALL COMPLY WITH TABLE R10235.
<br />EXTERIOR FIN15NE5:
<br />INSTALLATION OF EXTERIOR LATHING AND FRAMING APPLICATION REQUIREMENTS TO BE PER F.B.C,R. - 6TH EDITION (2011) R103.1.1 AND A5TM C 1063, ALL LATH AND LATH ATTACHMENTS SHALL BE
<br />OF CORRO5ION-RE515TANT MATERIAL, EXPANDED METAL OR WOVEN WIRE LATH 5HALL BE ATTACHED WITH 11/2 INCH 11 GAUGE NAILS HAVING A 1/16 INCH HEAD, OR 1/8 INCH LONG 16 GAUGE 5TAPLE6
<br />5PACED NO MORE THAN 6 INCHES, OR AS OTHERW15E APPROVED. THICKNE55 OF TEXTURED FIN15H OVER FRAME APPLICATION TO BE PER F.B.C.R - 6TH EDITION (2011) R103.12 AND A5TM C 926.
<br />PER F$.CR 6TH EDITION (2011) R103.12.1 WEEP 5CREEDS 5HALL BE A MINIMUM NO, 26 GALVANIZED SHEET GAUGE CORRO5ION-RE515TANT AEP 5CREED OR PLASTIC WEEP SCREED WITH A MINIMUM
<br />VERTICAL ATTACHMENT FLANGE OF 3-1/2 INCHES SHALL BE PROVIDED AT OR BELOW THE PLATE LINE ON EXTERIOR STUD WALLS IN ACCORDANCE WITH A5TM C 926. THE WEEP 5CREED SHALL BE
<br />PLACED A MINIMUM OF 4 INCHE5 ABOVE THE EARTH OR 2 INCHES ABOVE PAVED AREAS. THE WEATHER RE515TANT BARRIER SHALL LAP THE ATTACHMENT FLANGE. THE EXTERIOR LATH SHALL
<br />COVER AND TERMINATE ON THE ATTACHMENT FLANGE OF THE WEEP 5CREED. PER F.BC.R. 6TH EDITION (2011) R103.13 WATER RE6I5TIVE BARRIERS INSTALLED OVER WOOD BASED SHEATHING SHALL
<br />INCLUDE A WATER RE515TIVE VAPOR PERMEABLE BARRIER EQUIVALENT TO 2 LAYERS OF GRADE D PAPER STUCCO APPLICATION AND CURING PER F.B.CR 6TH EDITION (2011) R103.15 OR IN
<br />ACCORDANCE WITH A5TM G 926.
<br />5TUCC0 CONTROL JOINTS:
<br />STUCCO CONTROL JOINT5 TO BE INSTALLED PER A5TM C 1063-06 (1.11.4.1 THRU 1.11.4A) AT FRAMED WALL5 TO DELINEATE AREAS NOT MORE THAN 144 5.F. AND DELINEATE AREAS NOT MORE THAN 100
<br />5.F, FOR HORIZONTAL APPLICATIONS. D15TANCE BETWEEN CONTROL JOINTS SHALL NOT EXCEED 18 FT, IN EITHER DIRECTION OR A LENGTH -TO -WIDTH RATIO OF 2 1/2 TO I. A CONTROL JOINT SHALL BE
<br />INSTALLED WHERE CEILING FRAMING OR FURRING CHANGE DIRECTION, AND WHERE EXPANSION JOINT OCCUR5 IN BASE EXTERIOR WALL. WALL OR PARTITION HEIGHT DOOR FRAMES SHALL BE
<br />CONSIDERED A5 CONTROL JOINT5.
<br />EACH BEDROOM MUST HAVE ONE WINDOW THAT COMPLIES WITH EGRE55 CODE5, IF THERE 15 NO ACCE55 TO EXTERIOR THROUGH A DOOR THE WINDOW MUST HAVE A MAXIMUM CLEAR OPENING
<br />HEIGHT OF 44" ABOVE FIN15H FLOOR LINE OF THAT PARTICULAR ROOM.
<br />FLA5NING:
<br />I. FLASHING SHALL BE INSTALLED AT WALL AND ROOF INTERSECTIONS, DECK AND WALL INTERSECTIONS, AT GUTTERS, AT ALL CHAN6E5 IN ROOF SLOPE OR DIRECTION, AND AROUND ROOF OPENINGS.
<br />2. APPROVED CORRO5ION-RE515TANT FLASHING SHALL BE APPLIED SHINGLE FASHION IN SUCH A MANNER AS TO PREVENT ENTRY OF WATER INTO THE WALL CAVITY OR PENETRATION OF WATER TO
<br />THE BUILDING STRUCTURAL FRAMING COMPONENTS. THE FLASHING SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH. APPROVED CORRO5ION-RE515TANT FLA5NING SHALL BE
<br />INSTALLED AT ALL REQUIRED LOCATIONS PER R103.4.
<br />WINDOW INSTALLATION:
<br />1, WINDOWS SHALL BE INSTALLED AND FLASHED IN ACCORDANCE WITH THE MANUFACTURER5 WRITTEN INSTALLATION INSTRUCTIONS. WRITTEN INSTALLATION IN5TRUCTION5 SHALL BE PROVIDED BY THE
<br />MANUFACTURER FOR EACH WINDOW.
<br />2. IF STRUCTURE 15 IN A WIND-BORNE DEBRIS ZONE, AND REQUIRES PROTECTIVE 5HUTTER5 OR IMPACT GLASS, THE GENERAL CONTRACTOR 15 RESPONSIBLE FOR DETERMINING WHICH PROTECTIVE
<br />METHOD 15 TO BE USED.
<br />DWELLING / GARAGE OP NING5:
<br />THE OPENING BETWEEN THE GARAGE AND LIVING AREA SHALL BE EQUIPPED WITH 50LID WOOD DOORS NOT LE55 THAN 13/8" IN THICKNE55, SOLID CORE (S.C.) OR HONEYCOMB CORE STEEL DOORS
<br />NOT LE55 THAN 1 3/0" THICK, OR 20 MINUTE FIRE RATED DOORS.
<br />FLOOD ZONE REOUIRMNT5:
<br />PLAN MEETS OR EXCEEDS FEMA FLOOD FINISHED GARAGE FLOOR ELEVATION. IF FLOOD PORTS ARE REQUIRED IN GARAGE, REFER TO PLAN FOR CALCULATIONS AND QUANTITY.
<br />ASPHALT 5NINGL 5 (IF APPLICABLE) :
<br />1. WIND RE51STANCE OF ASPHALT SHINGLES. - ASPHALT SHINGLES SHALL BE INSTALLED IN ACCORDANCE WITH SECTION RW0 2b AND R9052b.1.
<br />2. ASPHALT SHINGLES SHALL ONLY BE USED ON ROOF 5LOPE5 OF TWO UNITS VERTICAL IN 12 UNITS HORIZONTAL (2:12) OR GREATER. FOR ROOF 5LOPE5 FROM TWO UNITS VERTICAL IN 12 UNITS
<br />HORIZONTAL (2:12) AND LE55 THAN FOUR UNITS VERTICAL IN 12 UNITS HORIZONTAL (4:12), TWO LAYERS OF UNDERLAYMENT COMPLYING WITH A5TM D Z26, TYPE I OR TYPE 11, A5TM D 4869, TYPE 11 OR
<br />TYPE IV OR A5TM D 615115 REQUIRED IN ACCORDANCE WITH SECTION R905.1.1. FOR ROOF 5LOPE5 FROM FOUR UNITS VERTICAL IN 12 UNITS HORIZONTAL (4:12) AND GREATER, ONE LAYER OF
<br />UNDERLAYMENT COMPLYING WITH A5TM D 226, TYPE 11, ASTM D 4869, TYPE IV OR A5TM D 615115 REQUIRED IN ACCORDANCE WITH SECTION R90511,
<br />CLAY AND CONCRETE TILE (IF APPLICA5LE) -
<br />THE INSTALLATION OF CLAY AND CONCRETE TILE PER F.BCR - 6TH EDITION (2011) R905.3 SHALL BE IN ACCORDANCE WITH THE MANUFACTURER'5 INSTALLATION INSTRUCTIONS, OR
<br />RECOMMENDATION5 OF FR5A/TRI FLORIDA HIGH WIND CONCRETE AND CLAY ROOF TILE INSTALLATION MANUAL,FIFTH EDITION WHERE THE VA5D 15 DETERMINED IN ACCORDANCE WITH SECTION R3012.13
<br />OR THE RECOMMENDATIONS OF RA5118,119 OR 120. REQUIRED UNDERLAYMENT PER F.B.CR - 6TH EDITION (2011) RW533 5HALL CONFOW WITH A5TM D 226, TYPE 11; A5TM D 2626, TYPE 11; OR A5TM
<br />D 1910 OR A5TM D 6380, CLA55 M MINERAL SURFACED ROLL ROOFING AND SHALL BE INSTALLED IN ACCORDANCE WITH FRSA/TRIFLORIDA HIGH WIND CONCRETE AND CLAY ROOF TILE
<br />INSTALLATION MANUAL, FIFTH EDITION WHERE THE VA5D 15 DETERMINED IN ACCORDANCE WITH SECTION R3012.13 OR THE RECOMMENDATIONS OF RA3 118,119 OR 120.
<br />CHIMNEY HEIGHT REQUIREMENTS (IF APPLICAELE) :
<br />WHEN STANDARD OR OPTIONAL FIREPLACE 15 TO BE INSTALLED THE CHIMNEY MUST EXTEND 34" PAST THE HIGHER POINT WHERE IT EXTENDS THROUGH THE ROOF AND MUST BE 2'-0" HIGHER THAN
<br />THE ROOF OR RIDGE THAT 15 10'-0" AWAY OR CLOSER,
<br />TU5 AND 5HOWER AR A5:
<br />CEMENT, FIBER -CEMENT, OR 6LA55 MAT GYPSUM BOARD (NO GREEN BOARD ALLOWED) IN COMPLIANCE WITH A5TM Cl288, 0325, OR 0118 AND INSTALLED IN ACCORDANCE WITH MANUFACTURER
<br />RECOMMENDATIONS SHALL BE USED AS BACKERS FOR WALL TILE IN TUB AND SHOWER AREAS, AND WALL PANELS IN SHOWER AREAS.
<br />TERMITE PROTECTION:
<br />1. PENETRATION. PROTECTIVE 5LEEVE5 AROUND PIPING PENETRATING CONCRETE SLAB -ON -GRADE FLOORS SHALL NOT BE OF CELLUL05E CONTAINING MATERIALS. IF 501L TREATMENT 15 USED FOR
<br />51,115TERRANEAN TERMITE PROTECTION, THE SLEEVE 5HALL HAVE A MAXIMUM WALL THICKNE55 OF 0,010 INCH, AND BE SEALED WITHIN THE 5LA8 U51N5 A NON -CORROSIVE CLAMPING DEVICE TO
<br />ELIMINATE THE ANNULAR SPACE BETWEEN THE PIPE AND THE SLEEVE. NO TERMITICIDES 5HALL BE APPLIED IN51DE THE SLEEVE.
<br />2, PROTECTION AGAINST DECAY AND TERMITES. - CONDENSATE LINES, IRRIGATION / SPRINKLER SYSTEM R15ER5 FOR SPRAY HEADS, AND ROOF DOWN5POUT5 SHALL DISCHARGE AT LEAST I FOOT
<br />(305 mm) AWAY FROM THE STRUCTURE 51DEWALL, WHETHER BY UNDERGROUND PIPING, TAIL EXTENSIONS, OR 5PLA5H 5LOCK5. GUTTERS WITH DOWN5POUT5 ARE REQUIRED ON ALL BUILDINGS WITH
<br />EAVES OF LESS THAN 6 INCHES (152 mm) HORIZONTAL PROJECTION EXCEPT FOR GABLE END RAKES OR ON A ROOF ABOVE ANOTHER ROOF.
<br />MECHANICAL AND NVAC:
<br />I. ENERGY CALCULATIONS FOR HEATING AND COOLING CAPACITIES 5HALL BE FURNISHED BY THE GENERAL CONTRACTOR A5 AN ATTACHMENT TO TH15 PLAN SET AT THE TIME OF APPLICATION FOR
<br />PERMIT.
<br />2. MECHANICAL APPLIANCES SHALL BE ACCE551151LE FOR INSPECTION, SERVICE, REPAIR, AND REPLACEMENT WITHOUT REMOVING PERMANENT CONSTRUCTION, OTHER APPLIANCES, OR ANY OTHER
<br />PIPING OR DUCTS NOT CONNECTED TO THE APPLIANCE BEING INSPECTED, SERVICED, REPAIRED, OR REPLACED. A LEVEL WORKING SPACE AT LEAST 30 INCHES (162 mm) DEEP AND 30 INCHES
<br />(162 mm) WIDE SHALL BE PROVIDED IN FRONT OF THE CONTROL 51DE TO 5ERVICE AN APPLIANCE.
<br />3, DUCTS IN THE GARAGE AND DUCTS PENETRATING THE WALL5 OR CEILINGS SEPARATING THE DWELLING FROM THE GARAGE SHALL BE CONSTRUCTED OF A MIN. 026 GAUGE (0.48 mm) 5HEET STEEL
<br />OR OTHER APPROVED MATERIAL AND SHALL HAVE NO OPENINGS INTO THE GARAGE.
<br />4. FOUNDATIONS AND 5UPPORT5 FOR OUTDOOR MECHANICAL 5Y57EM5 SHALL BE RAISED AT LEAST 3 INCHES (16 mm) ABOVE THE FINISHED GRADE AND SHALL AL50 CONFORM TO THE
<br />MANUFACTURER'5 INSTALLATION INSTRUCTIONS.
<br />5. AUXILIARY DRAIN PAN. CATEGORY IV CONDENSING APPLIANCES SHALL BE PROVIDED WITH AN AUXILIARY DRAIN PAN WHERE DAMAGE TO ANY BUILDING COMPONENT WILL OCCUR AS A RESULT
<br />OF STOPPAGE IN THE CONDENSATE DRAIN PIPING SYSTEM. THESE PANS SHALL BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE PROVISIONS OF 5ECTION5 M14113.
<br />EXHAUST FANS AND VENTING:
<br />1. OUTDOOR DISCHARGE. THE AIR REMOVED BY EVERY MECHANICAL EXHAUST 5Y5TEM SHALL BE D15GHARGED TO THE OUTDOORS. AIR SHALL NOT BE EXHAUSTED INTO AN ATTIC, SOFFIT, RIDGE
<br />VENT OR CRAWL SPACE.
<br />2. EXHAUST AIR FROM BATH ROOM5 AND TOILET ROOM5 SHALL NOT BE RECIRCULATED WITHIN A RESIDENCE OR TO ANOTHER DWELLING UNIT AND SHALL BE EXHAUSTED DIRECTLY TO THE
<br />OUTDOORS. EXHAUST AIR FROM BATHROOMS AND TOILET ROOMS SHALL NOT DISCHARGE INTO AN ATTIC, CRAWL SPACE, OR OTHER AREAS IN51DE THE BUILDING,
<br />3. DUCT LENGTH. THE MAXIMUM LENGTH OF A CLOTHES DRYER EXHAUST DUCT SHALL NOT EXCEED 35 FEET FROM THE DRYER LOCATION TO THE WALL OR ROOF TERMINATION. IF DUCT LENGTH
<br />EXCEEDS 35' THEN PERMANENT LABEL OR TAG MUST BE INSTALLED. THE MAXIMUM LENGTH OF THE DUCT SHALL BE REDUCED 2.5 FEET (162 mm) FOR EACH 45 DEGREE (0.19 RAD) BEND AND 5 FEET
<br />(1524 mm) FOR EACH W DEGREE (lb RAD) BEND. THE MAXIMUM LENGTH OF THE EXHAUST DUCT DOES NOT INCLUDE THE TRAN51TION DUCT. EXCEPTION - WHERE A CLOTHES DRYER 5005TER FAN 15
<br />IN5TALLED AND L15TED AND LABELED FOR THE APPLICATION, THE MAXIMUM LENGTH OF THE EXHAUST DUCT, INCLUDING ANY TRAN51TION DUCT, 5HALL BE PERMITTED TO BE IN ACCORDANCE WITH
<br />THE B005TER FAN MANUFACTURER'S INSTALLATION IN5TRUCTION5. WHERE A CLOTHES DRYER 5005TER FAN 15 INSTALLED AND NOT READILY ACCE5515LE FROM THE ROOM IN WHICH THE DRYER 15
<br />LOCATED, A PERMANENT IDENTIFYING LABEL 5HALL BE PLACED ADJACENT TO WHERE THE EXHAUST DUCT ENTERS THE WALL. THE LABEL 5HALL BEAR THE WORDS "TH15 DRYER EXHAUST 5Y5TEM 15
<br />EQUIPPED WITH A REMOTELY LOCATED BOOSTER FAN."
<br />4. PROVIDE LOUVER DEVICES AT INTAKE AND EXHAUST LOCATIONS IN ACCORDANCE WITH AMCA STANDARD 550 IN FBC.
<br />ATTENTION GENERAL CONTRACTOR / 5UILDR:
<br />156UANCE OF PLANS FROM TH15 DRAFTER'S OFFICE SHALL NOT RELIEVE THE BUILDER OF RE5PON5181LITY TO REVIEW AND VERIFY ALL NOTES, DIMEN51ON5, AND ADHERENCE TO APPLICABLE
<br />BUILDING CODES PRIOR TO COMMENCEMENT OF ANY CONSTRUCTION. ANY DISCREPANCY OF ERROR IN NOTES, DIMENSIONS, OR ADHERENCE TO APPLICABLE BUILDING CODES SHALL BE BROUGHT
<br />TO THE ATTENTION OF THE DRAFTER'5 OFFICE FOR CORRECTION BEFORE COMMENCEMENT OF ANY CONSTRUCTION CORRECTION / REVI51ON5. ANY REV1510N5 OR CHANGES, NOT RELATED TO THE
<br />CORRECTION OF ERRORS THAT ARE MADE AFTER THE FINAL PLANS HAVE BEEN COMPLETED SHALL BE 50JECT TO ADDITIONAL FEES. IF ANY MODIFICATIONS ARE MADE TO THESE PLANS BY ANY
<br />OTHER PARTY OTHER THAN THE DRAFTER'S OFFICE, THE DRAFTER 5HALL NOT BE HELD RESPONSIBLE.
<br />REV.12-31-2011
<br />REVISION LOG
<br />7/17/18
<br />1.0
<br />CREATED LOT SPECIFIC PLAN ELEVATION "A" GARAGE LEFT
<br />35981 SADDLE PALM WAY
<br />EPHYRHILLS, FL 33541
<br />LE N NARM
<br />2277
<br />- LEFT
<br />INDEX OF DRAWINGS
<br />SHT. NO.
<br />DESCRIPTION
<br />CS
<br />COVER SHEET
<br />1
<br />FLOOR PLANS
<br />2
<br />INTERIOR ELEVATIONS
<br />3
<br />EXTERIOR ELEVATIONS
<br />4
<br />ELECTRICAL PLANS
<br />5
<br />ROOF PLANS
<br />6
<br />FOUNDATION PLANS
<br />7
<br />ROOF FRAMING PLANS
<br />8
<br />LINTEL PLAN AND DETAILS
<br />SN
<br />STRUCTURAL NOTES
<br />SN 1
<br />DETAILS NNoti31 f r''!°®,
<br />S3
<br />DETAILS ,,7„
<br />S4
<br />DETAILS
<br />S5
<br />• of � C�
<br />DETAILS '�
<br />.. , o ,
<br />SS
<br />RETROFIT DETAILS
<br />WP
<br />WATERPROOFING DETAILS ®°0'"fli e0%
<br />PA1.0
<br />PRODUCT APPROVAL NUMBERS
<br />PA1.1
<br />PRODUCT APPROVAL NUMBERS
<br />PA1.2
<br />PRODUCT APPROVAL NUMBERS
<br />IPA1.3
<br />PRODUCT APPROVAL NUMBERS
<br />if�liiltf bAf .��
<br />ABBREVIATIONS
<br />AFF.
<br />ABOVE FINISH FLOOR
<br />EXG.
<br />EXISTING
<br />PKG.
<br />PARK6W
<br />ACC.
<br />ACCESS
<br />EXT.
<br />EXTERIOR
<br />PTN
<br />PARTITION
<br />AP.
<br />ACCESS PANEL
<br />F.E.
<br />FACE BRICK
<br />PV.
<br />PAVE(DXINS)
<br />ADO.
<br />ADDENDUM
<br />P.C.
<br />FACE OF
<br />"T.
<br />PAVEMENT
<br />ADH.
<br />ADHE51VE
<br />PAS.
<br />FA5TEN(ER)
<br />FED.
<br />PEDESTAL
<br />ADJ.
<br />ADJUSTABLE
<br />FN
<br />FENCE
<br />PERT.
<br />PERIMETER
<br />AGG.
<br />AGGREATE
<br />FGL.
<br />FIBEFiGLA55
<br />PLAS.
<br />PLASTER
<br />AIC
<br />AIR CONDITIONING
<br />PIN..
<br />FN5H
<br />PLAM. OR P1.
<br />PLASTIC LAMINATE
<br />ALT.
<br />ALTERNATE
<br />FFL
<br />I FINSH FLOOR LINE
<br />PL,
<br />PLATE
<br />A.B.
<br />ANCHOR BOLT
<br />Ff.
<br />FIRE EXTINGUISHER
<br />P.V.C.
<br />POLYVINYL CHLORIDE
<br />APPX.
<br />APPROXIMATE
<br />FP.
<br />FIREPLACE
<br />PE.
<br />PORCELAIN ENAMEL
<br />ARCH.
<br />ARCHITECT
<br />FLG.
<br />FLA5HING
<br />PSF,
<br />POUNDS PER SQUARE FOOT
<br />AD,
<br />AREA DRAIN
<br />PI-R.
<br />FLOORING)
<br />P.S.I.
<br />POUNDS PER SQUARE INCH
<br />A5PH.
<br />ASPHALT
<br />PD.
<br />FLOOR DRAM
<br />P.C.C. OR P.C.CONC.
<br />PRECAST CONCRETE
<br />A.T.
<br />ASPHALT TILE
<br />FLUB
<br />FLUORESCENT
<br />M. OR PREFAB.
<br />PREFABRICATED)
<br />AUTO.
<br />AUTOMATIC
<br />FTG.
<br />FOOTING
<br />Q.T.
<br />QUARRY TILE
<br />AWN.
<br />AWNING
<br />FIND.
<br />FOUNDATION
<br />RAD.
<br />RADIUS
<br />551T.
<br />BASEMENT
<br />FR.
<br />FRAME(DXING)
<br />RI-G.
<br />RAILING
<br />BM.
<br />BEAM
<br />F.5.
<br />FULL 514E
<br />REF.
<br />REFERENCE
<br />BRG.
<br />BEARING
<br />FB.O.
<br />FUR415HED BY OTHERS
<br />REFR,
<br />REFRIGERATOR
<br />all.
<br />BENCH MARK
<br />FUR.
<br />PURR(EDXING)
<br />RE, OR REINF.
<br />REINFORC(EDXING)
<br />BVL.
<br />BEVELED
<br />GA
<br />GAUGE
<br />RES.
<br />RESILIENT
<br />BIT.
<br />BITUMINOUS
<br />G.I.
<br />GALVANIZED IRON
<br />RA.
<br />RETURN AIR
<br />BILK,
<br />BLOCK
<br />G.G.
<br />GENERAL CONTRACT(OR)
<br />RV5.
<br />REVERSE (SIDE)
<br />BLKG.
<br />BLOCKING
<br />GL.
<br />GLASS, GLAZING
<br />REV.
<br />REAION(S), REVISED
<br />BD,
<br />BOARD
<br />GLB.
<br />GLA55 BLOCK
<br />ROW,
<br />RIGHT OF WAY
<br />B.S.
<br />BOTH 51DE5
<br />GD.
<br />GRADE, GRADING
<br />R.
<br />P15ER
<br />BID.
<br />BOTH WAYS
<br />GB. OR GYPBD,
<br />GYPSUM BOARD
<br />RD.
<br />ROOF DRAIN
<br />80T.
<br />BOTTOM
<br />HD.
<br />HARD
<br />RFG.
<br />ROOFING
<br />BR,
<br />BRICK
<br />HDW.
<br />HARDWARE
<br />RM.
<br />ROOM
<br />BLDG.
<br />BUILDING
<br />HDR
<br />HEADER
<br />R0,
<br />ROUGH OPENING
<br />CAB.
<br />CABINET
<br />HTG.
<br />HEATING
<br />IRBL.
<br />RUBBLE
<br />CPT. OR C.
<br />CARPET
<br />HVAC.
<br />HEATING/VENTILATING/AIR CONDITIONING
<br />SOH.
<br />SCHEDULE
<br />C5MT,
<br />CASEMENT
<br />HD.
<br />HEAVY DUTY
<br />5NT.
<br />SEALANT
<br />G.I.
<br />CAST IRON
<br />HGT. OR HT.
<br />HEIGHT
<br />5TG,
<br />5EATING
<br />C.IP.CCNC.
<br />CAST -IN -PLACE CONCRETE
<br />H.C.
<br />HOLLOW CORE
<br />SEC.
<br />SECTION
<br />CB.
<br />CATCH DA51N
<br />HM.
<br />HOLLOW METAL
<br />SHTHG.
<br />SHEATHING
<br />CK.
<br />CALK(ING) CAULKING)
<br />HORZ
<br />HORIZONTAL
<br />5HT,
<br />SHEET
<br />CLG.
<br />CEILING
<br />H.B.
<br />H05E BIBS
<br />5H.
<br />SHELF, SHELVING
<br />GEM,
<br />CEMENT
<br />D.
<br />INSIDE DIAMETER
<br />SIM,
<br />51MILAR
<br />CM.
<br />CENTIMETERS)
<br />INS.
<br />NSJLAttEDXIOW
<br />SKI-.
<br />SKYLIGHT
<br />CEP
<br />CERAMIC
<br />INT.
<br />INTERIOR
<br />5L.
<br />SLEEVE
<br />C.T.
<br />CERAMIC TILE
<br />A
<br />JOINT
<br />S.C.
<br />50LID CORE
<br />CRAM.
<br />CHAMFER
<br />J5T.
<br />JOIST
<br />BPC,
<br />SPACER
<br />CUR.
<br />CIRCLE
<br />KIT.
<br />KITCHEN
<br />SPKR.
<br />SPEAKER
<br />CIRC.
<br />CIRCUMFERENCE
<br />K.O.
<br />KNOCKOUT
<br />SPEC.
<br />SPECIFICATIONS
<br />CLR
<br />CLEARANCE)
<br />LAM,
<br />LAMINATED
<br />50.
<br />SQUARE
<br />CLG.
<br />CLOSURE
<br />LP.
<br />LAMINATED PLASTIC
<br />55T.
<br />STAINLESS STEEL
<br />COL.
<br />COLUMN
<br />LAY.
<br />LAVATORY
<br />STD,
<br />STANDARD
<br />COMB.
<br />COMBINATION
<br />LT.
<br />LIGHT
<br />St.
<br />STEEL
<br />CONC.
<br />CONCRETE
<br />LTL.
<br />LINTEL
<br />5TO.
<br />STORAGE
<br />CM.U.
<br />CONCRETE MASONRY UNIT
<br />LL.
<br />LIVE LOAD
<br />STR-.
<br />STRUCTURAL
<br />cX
<br />CONNECTION
<br />LIv.
<br />LIvW,
<br />5U5.
<br />SUSPENDED
<br />CON5TR:
<br />CONSTRUCTION
<br />LVR
<br />LOUVER
<br />TEL,
<br />TELEPHONE
<br />CONT.
<br />CONTINUOUS
<br />MA.
<br />MANHOLE
<br />TV.
<br />TELEVISION
<br />CENTR
<br />CONTRACTOR
<br />MFR.
<br />MANUFACTURER)
<br />THK
<br />THICK(NEW
<br />G.J.
<br />CONTROL OR CONSTRUCTION JOINT
<br />MAS.
<br />MASONRY
<br />THR OR THU).
<br />THRESHOLD
<br />CORK
<br />CORRUGATED
<br />M.O.
<br />MASONRY OPENING
<br />T *.
<br />TONGUE AND GROOVED
<br />CTR.
<br />COUNTER
<br />MATL
<br />MATERIAL
<br />T.O.C.
<br />TOP OF CONCRETE
<br />CRS.
<br />COURSES)
<br />MAX
<br />MAXIMUM
<br />TOR
<br />TOP OF FOUNDATION
<br />CF.
<br />CUBIC FOOT
<br />MECH.
<br />MECHANICAL
<br />TR
<br />TREAD
<br />C.Y.
<br />CUBIC YARD
<br />M.C. OR MED.CAB.
<br />MEDICINE CABINET
<br />TYP.
<br />TYPICAL
<br />D.P.
<br />DAMP -PROOFING
<br />MMB.
<br />MEMBRANE
<br />UC.
<br />UNDERCUT
<br />%,
<br />DEAD LOAD
<br />MET. OR MTI_
<br />METAL
<br />UNF,
<br />UNFINISHED
<br />DEP.
<br />DEPRESSED
<br />M.
<br />METER
<br />VB.
<br />VAPOR BARRIER
<br />DET, OR II
<br />DETAIL
<br />MM.
<br />MILLIMETER
<br />VERT.
<br />VERTICAL
<br />pIAM. OR i
<br />DIAMETER
<br />MIN
<br />MN M d1
<br />viN OR v.
<br />VINYL
<br />DIM.
<br />DIMENSION
<br />MIR
<br />MIRROR
<br />Y.T.
<br />VINYL TILE
<br />D.W.
<br />DISH WASHER
<br />MISC.
<br />MISCELLANEOUS
<br />WS(-T.
<br />WAINSCOT
<br />DR.
<br />DOOR
<br />MOD.
<br />MODULAR
<br />W.T.W.
<br />WAI-L TO WALL
<br />D.H.
<br />DOUBLE HUNG
<br />MLD.
<br />MOLDING, MOULDING
<br />W.N.
<br />WALL HUNG
<br />ELEC.
<br />ELECTRIUAL)
<br />O.C.
<br />ON CENTER
<br />WF.
<br />WIDE FLANGE
<br />D.5.
<br />DOWNSPOUT
<br />MT.
<br />MOUNT(EDXING)
<br />W.C.
<br />WATERCLOSET
<br />EP.
<br />ELECTRICAL PANEL
<br />CA.
<br />OVERALL
<br />W/O.
<br />WITHOUT
<br />D.
<br />DRAIN
<br />MULL.
<br />MULLION
<br />W.P.
<br />WATER PROOFING
<br />EL.
<br />ELEVATION
<br />OR OR CHEAP.
<br />OVERHEAD
<br />WD,
<br />WOOD
<br />D.T.
<br />DRAIN TILE
<br />NL.
<br />NAILABLE
<br />W.R.
<br />WATER RESISTANT
<br />EQ.
<br />EQUAL
<br />PNT.
<br />PAINT(ED)
<br />W.I.
<br />*OUGHT IRON
<br />DWR.
<br />DRAWER
<br />NOP1.
<br />NOMINAL
<br />W.WM.
<br />WELDED WIRE MESH
<br />EST,
<br />ESTIMATE
<br />M.
<br />PANEL
<br />W.
<br />WIDTH, WIDE
<br />DUK,.
<br />DRAWING
<br />N.I.C.
<br />NOT IN CONTRACT
<br />WIN
<br />WINDOW
<br />EXH,
<br />EXHAUST
<br />PAR
<br />PARALLEL
<br />EF. OR EAR
<br />EACH FACE
<br />NTS.
<br />NOT TO SCALE
<br />� E�iS
<br />DESIGN GR®VP
<br />150 STATE STREET EAST
<br />OLL�SMAR, FLORIDA 346T7
<br />813. 925.1300 TFL
<br />813.9�5.1800 FAX
<br />W W W.L7AVISBEWS.COM
<br />TAMPA • DENVER.
<br />-� - EST. 1994
<br />rii,6231,1111fimiji.
<br />VORTEX ENGINEERING, I.I.C.
<br />607 S. ALEXANDER ST., SUITE 103
<br />PLANT CITY, FLORIDA 33563
<br />813,704.4842
<br />COA 28035
<br />PAUL D. KIDWELL, P.E. #52683
<br />ANDREW J. MEISHEID, P.E. #83217
<br />1 HEREBY CERTIFY THAT I HAVE REVIEWEDTHE
<br />ATTACHED DESIGN, AND FIND IT TO BE IN COMPLIANCE
<br />WITH SECTION R301 OFTHE FLORIDA BUILDING CODE,
<br />RESIDENTIAL 6TH EDITION (2017).
<br />THE ENGINEER HAS NOT REVIEWED THE
<br />PRE-ENGINEERED TRUSS MANUF. LAYOUT TO
<br />DETERMINE ANY LOAD BEARING CONDITIONS AND
<br />RESERVES THE RIGHT TO MAKE ANY CHANGES AFTER
<br />TRUSS LOAD INFORMATION IS SUPPLIED TO THE
<br />ENGINEER.
<br />SEALED FOR STRUCTURE ONLY
<br />0
<br />Z
<br />N
<br />0A:_o
<br />> (n M o
<br />0
<br />� �Ln
<br />� � �
<br />�LL
<br />ca. 0-11
<br />z < E
<br />� V Q00
<br />z§f�
<br />wW
<br />J o
<br />d-
<br />=Z
<br />O
<br />w�
<br />z¢
<br />w¢�w
<br />uzoo
<br />oaU
<br />a a
<br />_ o W Z
<br />aLLJ
<br />Lu
<br />o Lu N
<br />F- w
<br />zo
<br />I- O z w
<br />z w g�
<br />uj
<br />O Ln
<br />w0¢
<br />z F<a
<br />W w
<br />O�w
<br />W Wa92
<br />U ¢
<br />� w
<br />O > �a�o
<br />0w0wU
<br />< � HOa8
<br />Z r4 N C~
<br />Z Ln N ( �<ao
<br />0oinw
<br />Q3�
<br />Q ¢ 3 0 O
<br />Oce
<br />Z <�U
<br />a>O
<br />i Q pm
<br />r, m a a
<br />SCALE : AS NOTED
<br />DATE : 7/ 17/2018
<br />VERSION NO.
<br />iso
<br />SHEEP NO,
<br />c s
<br />DAVIS
<br />a
<br />
|