|
_
<br /> . �.",�
<br /> 1
<br /> �RIf�IIY i IERD
<br /> ;
<br /> APPENDIX 1:ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE , - � �
<br /> Table Deck Application Type Description � ! Page
<br /> 1A Wood New,Reroof(Tear-Of�,Recover C Mechanically Attached Insulation,Bonded Roof C r ��� 3
<br /> 1B Wood ` New Construction F Non-Insulated,Bonded Roof Cover �„ � � 3
<br /> 2A Steel or Conc. New,Reroof(Tear-Offl,Recover C Mechanically Attached Insulation,Bonded Roof C�� _ � 4-6
<br /> 2B-1 Steel or Conc. New,Reroof(Tear-Offl,Recover D Insulated,Mechanically Attached Roof Cover(Str� t� W } 7
<br /> 2B-2 Steel or Conc. New,Reroof(Tear-Of�,Recover D Insulated,Mechanically Attached Roof Cover(Bat�e � � �-- /� � 8
<br /> n �
<br /> 3A Concrete New,Reroof(Tear-Of� A-1 Bonded Insulation,Bonded Roof Cover !Q �a � 9-10
<br /> 3B Concrete New,Reroof(Tear-Off) F Non-Insulated,Bonded Roof Cover. � U �j � 10
<br /> e-.�
<br /> 4A Various Recover A-1 Bonded Insulation,Bonded Roof Cover ,:•' �i. � � z 11-12
<br /> The following notes apply to the systems outlined herein: -�.� a W '� � U �
<br /> 1. The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC re�ir�n�t�o the satisfaction of the AHJ. Load resistance of the
<br /> roof deck shall be documented through proper codified and/or FBC Approval documentation. .
<br /> 2. Unless otherwise noted,fasteners and stress plates for insulation attachment shall be as follows. Fasteners shall be of sufficient length for the following engagements:
<br />' ➢ Wood Deck: Mule-Hide HDP Fastener with Mule-Hide 3 in.Insulation Plate,OMG#12 or#14 Roofgrip with Flat Bottom Plate,OMG#12 Standard or#14 HD with OMG Standard metal plate,Dekfast#12
<br /> or#14 with Hex Plate,Tru-Fast DP or HD with MP-3 Plates. Minimum�-inch plywood penetration,or 1-inch wood plank embedment
<br /> ➢ Steel Deck: Mule-Hide HDP Fastener with Mule-Hide 3 in.Insulation Plate,OMG#12 or#i14 Roofgrip with Flat Bottom Plate,OMG 4�12 Standard or#14 HD with OMG Standard metal plate,Dekfast#12
<br /> or q14 with Hex Plate,Tru-Fast DP or HD with MP-3 Plates. Minimum%-inch steel penetretion,engage the top flute of the steel deck.
<br /> ➢ Concrete Deck: Mule-Hide HDP Fastener or Mule-Hide CF with Mule-Hide 3 in.Insulation Plate,OMG#14 Roofgrip with Flat Bottom Plate,OMG#14 HD or CD-10 with OMG Standard metal plate,Dekfast
<br /> #14 or Dekspike with Hex Plate,Tru-fast HD or CF with MP-3 Plates.Minimum 1-inch embedment. Fasteners installed with a pilot hole in accordance with the fastener manufacturer's
<br /> published installation instructions.
<br /> 3. Unless otherwise noted,insulation may be any one layer or combination of polyisocyanurate,polystyrene,wood fiberboard,perlite,Dens Deck,Dens Deck Prime,SECUROCK Gypsum-Fiber Roof Board or SECUROCK
<br /> Glass-Mat Roof Board that meets the QA requirements of F.A.C.Rule 61G20-3 and is documented as meeting FBC 1505.1 and,for foam plastic,FBC 2603.4.1 or 2603.6,when installed with the roof cover.
<br /> 4. Minimum 200 psi,minimum 2-inch thick lightweight insulating concrete may be substituted for rigid insulation board for System Type D(mechanically attached membrane),whereby the membrane fasteners are
<br />� installed through the LWIC to engage the structural steel or concrete deck. The structural deck shall be of equal or greater configuration to the steel and concrete deck listings.
<br />� 5. Preliminary insulation attachment for System Type D=Minimum four fasteners per 4 x 8 ft board or minimum two fasteners per 4 x 4 ft board.
<br /> 6. Unless otherwise noted,insulation adhesive application retes are as follows. Ribbon or bead width is at the time of application;the ribbons/beads shall expand as noted in the manufacturer's published instructions:
<br /> ➢ Hot Asphalt: Applied at a rate of 20-40 Ibs./sq.
<br /> ➢ OlyBond 500: Continuous'/<to 1-inch wide ribbons,12-inch o.c.using PaceCart or SpotShot application devices.
<br /> ➢ Note: When multiple layers(s)of insulation and/or coverboard are installed in ribbon-applied adhesive,adhesive ribbons shall be staggered from layer-to-layer a distance of one-half the ribbon spocing.
<br /> ➢ Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation boord sholl be not less than one-half the specified ribbons spocing
<br /> _ ,
<br /> Exterior Research and Design,LLC.d/b/a Trinity� ERD Evaluation Report M31240.11.09-R4 for FL10703-RS
<br /> Certificate of Authorization#9503
<br /> , Revision 4:12/19/2014
<br /> Prepared by: Robert Nieminen,PE-59166 Appendix 1,Page 1 of 12
<br />
|