15-16527 - Laserfiche WebLink

Browse Search

I M G31 QA-A ' " 'Revised February 20, 2007 Page 21 . . . � - � TROU�L�SHQOTING GU�DE � � • If there is NO gas flow ta the stove,verify that the (continued) gas valve is plugged into the Gas Shut Off Assernbly cantral box. CAUT(ON: DURING CHECK OUT � (The gas valve is normally closed and is PROGEDURES MAKE SURE SAFETY PULL energized when power is supplied to it.) PIN IS tNSTALl.ED. � If there is still NO gas flow, unplug the gas valve • Confirm that the installation of Sonic Receiver is � and measure for 24 VAC voltage between the not obstructed from receiving the audio signal. black and white wires. !f there is voitage Verify that the location and the db level measured at the connector, replace the gas {loudness} is adequate by opening cabinet. If � Valve. electric shutoff activates, installation of a remote NOTE: After performing the above steps and there is �larm may be necessary to compensate far the 24VAC at plug and if the gas flow indicator light is not to�bea S�d��Ret or an Interconnect Ca61e wi�l have lit indica#ing gas flow, check the bulb indicator light. It may need to be replaced. � tf any unknown in#erfere�ce occurs from a site ( (f there is NO voltage at the connector that condition the In#erconnect Cable may have to be I � used. ! plugs inta the valve, replace the Gas Shutaff Gantrol box. Gas Shutofftp�N�3,s.,a� Problem:No Shutaff Activation-Interconnect Proble�t'1: No Electrical Power To Stove Cable or the Sonic Receiver Assv • Confirm power is supplied at the wall outlet. If no ! ' Ganfirm fhaf power is supptied to "Gas Shutoff power to the stove exist,check the site condition. I Cnntrol Box". If no power exist, perForm the � steps under "No Electrical Pawer �a Stove" on • If power exist at the wall outlet, unplug the stove � Page 20. fram wall outlet and plug it into Gas Shutoif • P�rtorm the TEST PROCEDURES for either the Control box. ' tNTERCONNEGT CAB�E or SQh(IC RECEEVER I ASSEMBLY on Page 16 8�17. � Verify that ths"Power ReseY'push buttan switch • If no activation,replace the gas shutot�. is pushed. Etectrical power is supp(ied to fhe � stpve. (See FIGURE 1$) ; SOI11C R@C@IV@I" ASS�/ (P/N G3'!5-A) • DO NOT push the"VALVE RESET"switch at#his � time. Pushing the VALVE RESET switch will Problem:NoSonicActivation enable gas to flaw to the sfave. • Perform "Sonic Receiver Test Procedures" • If power still doe5 NpT exist to the stove, unplug Checkout on Page 16. stave fram fhe Gas Shutoff Cantrol box and check far 115 VAC on the control box outlet. If • Check that"Sonic Receiver Assembly"is plugged there is no power, replece the contro!box. into either the gas or electric shutoff. Power ' °C}EV" lighf will be I�t This indicafes power is Problem' No G�s Flow to Stove being supplied to the Sonic Receiver board. • Confirm that the"source power"is supplied to the • Canfirm that tfie insta(lation of Sonic Receiver is Gas Shutaff Control box. nat obstructed fram receiving the audio signal. Verify that the }ocation and the db level � • Verify that the"Power ReseY' push button switch � t�pudness)is adequate by opening cabinet. is pushed to supply power to the stove and to the tf shutaff acfivates by increasing the db leve! af the "Valve Reset" switch on fhe Gas Shutoff • saund, installation of a Remote Alarm ma be Gontrol Box. � necessary to compensate for the type of cab net. (The Power Reset switch suppiies pawer ta the � Valve Resef Swifch. This is a safety feafure.) I If the db level of laudness is adequate, replace • Push the "Valve Reset" switch far gas flow to � • the Sonic Receiver board or substitute an the stove. The gas flow indica#ar light is lit. �ntercannecf Cable in place of the Sonic Receiver � Assembly. � • If any unknown interference occurs from a site � condition the Interconnect Cable may have to be used.See Page 8&16. I �