Laserfiche WebLink
t� <br /> ��, r�� .,... � <br /> �.�` TRINITY�ERD , . <br /> 15. For adhered membrane systems,side laps shall be minlmum 2-inch wide sealed with min.1.5-inch heat weld. Unless otherwise noted,mem6rane adhesive application rates are as follows: <br /> Membrane Adhesive Method Rate <br /> Sure-Weld or S ectro-Weld Sure-Weld eondin Adhesive Contact both sides 60 ft/ al <br /> 5ure-Weld or S ectraWeld A ua Base 120 Bondin Adhesive Contact(both sides 120 ft/ al <br /> Sure-Weld or S ectro-Weld Low VOC Bonding Adhesive Contact(both sides 60 ft/gal <br /> Sure-Weld Sure-Seal 90-8-30A Bonding Adhesive Contact(both sides) 60 /gal <br /> Sure-Weld FleeceBACK Aqua Base 120 Bonding Adhesive Wet lay(substrete) 120 h/gal <br /> Sure-Weld FleeceBACK H droBond Water-Based Adhesive Wet la (substrate 300 to 133 ft/ al <br /> Sure-Weld FleeceBACK FAST 100,FAS�100W,Flexible FAST Wet lay(substrete) Full coverage at 100 ft/gal or Ribbons spaced as noted herein,spread to 2-3 Inch,roof cover <br /> set and rolled with 50 Ib roller. <br /> 5 ectraWeld FleeceBACK FAST 100W,Flexible fAST Wet lay substrate 100 ft/gal <br /> 16. For membrane systems attached using TPO 10-inch Pressure-Sensitive RUSS,the underside of the membrane wh(ch comes in conWct with the tape shall be primed with TPO Primer, The membrone shall be secured <br /> by placing the pr(med portion onto the tape portion of the Sure-Weld TPO SO-inch Pressure-Sensitive RU55 and roll with a steel hand roller to ensure contact. <br /> 17. For adhered membrane systems,unless otherwise noted: <br /> D Reference to"Sure-Weld"membrane below also Includes"Sure-Weld EXTRA"and"Spectro-Weld"; <br /> _ _ D Referenee to"Sure-Weld FleeceBACK"Includes 300 115 and 135• <br /> _.....___..._......._.-- --•-�----___—__--�- -- -----•- ---�----.....--- --�------------.__.._._ ._..__----..._._.._......------.._-----�--�------�------_...._----.._...__.._._...,.___.__._....._._.,.,_._._�..-•--�----__.._..._.......__......�._.....___----• -._�...___......_.....----��.....,_....,.,...... —�... <br /> ➢ ��Refe�ence to"Sure-Weld AFX"fncludes i4FX 120,AFX 135 and AFX 155; <br /> D Reference to"Sure-Weld FleeceBACK"includes Spectro-Weld FleeceBACK applied in FAST 100LV(full coverage)only. <br /> 18. "MDP"=Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC 1609 for determination of design wind loads. <br /> Exterior Research and Design,LLC.d/b/a Triniry�ERD Evaluation Report C33680.09.10-R10 for FL34083-R10 <br /> Certiflcate of Authorization N9503 Revislon 10:10/19/2015 <br /> Prepared by, Robert Nieminen,PE•59166 ' Appendix 1,Page 3 of 39 <br />