16-17524 - Laserfiche WebLink

Browse Search

, , �f'�I�II�''�E�� Continue upslope in a similar manner,maintaining minimum 3-inch side-laps and minimum 6-inch end-laps. Fasten 6- inch o.c.in the laps and 12-inch o.c.in two,equally spaced,staggered center rows in the field. Ensure all end laps are staggered at least 3-feet apart. One the same day,install Liberty'"'SBS Self-Adhering Base/Ply;StormGuard�Film Surfaced Leak Barrier;UnderRoof""2 Polyester-Surfaced Leak Barrier; UnderRoof'"' HT High Temperature Leak Barrier; WeatherWatch° Mineral Surfaced Leak Barrier or WeatherWatch�XT Mat Surfaced Leak Barrier over the StormSafe'""Anchor Sheet. 6.6 RoofPro'""SBS-Modified All-Purpose Underlavment and ShinQle-Mate�Roof Deck Protection: 6.6.1 Install RoofPro'"' and Shingle-Mate° in compliance with manufacturer's published installation instructions and the requirements for ASTM D226,Type I and II underlayments in FBC Sections 1507 for the type of prepared roof covering � to be installed. A double layer is required for 2:12<roof slope<4:12. No hammer tacks or staples are permitted. 6.6.2 Optional, or if required by the Authority Having Jurisdiction: Install a leak barrier of LibertyTM SBS Self-Adhering Base/Ply Sheet;StormGuard� Film 5urfaced Leak Barrier; UnderRoofn"2 Polyester-Surfaced Leak Barrier; UnderRoof7"' HT High Temperature Leak Barrier; WeatherWatch� Mineral Surfaced Leak Barrier or WeatherWatch� XT Mat Surfaced Leak Barrier at vulnerable leak areas,including but not limited to eaves,valleys,rakes,skylights and dormers. At eaves and valleys, install the leak barrier prior to installation of the underlayment. Along the rake, install the underlayment, leaving 6 to 8-inch of the deck exposed, and then install the leak barrier over the underlayment and exposed decking. At other areas,install the leak barrier over the underlayment. 6.7 VersaShield�Fire-Resistant Roof Deck Protection: 6.7.1 Install VersaShield° Fire-Resistant Roof Deck Protection in compliance with manufacturer's published installation instructions and the requirements for ASTM D226,Type I and II or ASTM D4869 underlayments in fBC Sections 1507 for the type of prepared roof covering to be installed. A double layer is required for 2:12 < roof slope <4:12. No hammer tacks or staples are permitted. 6.7.2 Optional, or if required by the Authority Having Jurisdiction: Install a leak barrier of LibertyTM SBS Self-Adhering Base/Ply Sheet;StormGuard� Film Surfaced Leak Barrier; UnderRoof'"'2 Polyester-Surfaced Leak Barrier; UnderRoof'"' HT High Temperature Leak Barrier; WeatherWatch� Mineral Surfaced Leak Barrier or WeatherWatch� XT Mat Surfaced Leak Barrier at vulnerable leak areas,including but not limited to eaves,valleys,rakes,skylights and dormers. At eaves and valleys, install the leak barrier prior to installation of the underlayment. Along the rake, install the � underlayment, leaving 6 to 8-inch of the deck exposed, and then install the leak barrier over the underlayment and exposed decking. At other areas,install the leak barrier over the underlayment. 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 8. MANUFACiURING PLANTS: Contact the manufacturer or the named QA entity for information on plants covered under Rule 61G20-3 Qq requirements. 9. QUALITY ASSURANCE ENTITY: UL,LLC.—QUA9625;(847)664-3281 -END OF EVALUATION REPORT- Exterior Research and Design,LLC. Evaluation Report 01506.03.12-RS Certificate ofAuthorizatian JI95o3 FL15487-RS Revisian 5:04/02/2015 Page 5 of 5