Laserfiche WebLink
TRINITY ERD <br /> 5.5 Allowable roof c ers applied atop CertainTeed underlayments are as follows: <br />� TABLE 1: ROOF COVER OPTIONS <br /> Asphalt Foam-On Mortar-Set Wood <br /> Underlayment Nail-On Tile Metal Shakes& Slate <br /> Shingles Tile Tile <br /> Shingles <br /> Roofers'Select Yes No No No No No No <br /> WinterGuard HT Yes No No No Yes Yes Yes <br /> WinterGuard Sand r <br /> Granular Yes No No No No Yes Yes <br /> Black Diamond Bas Yes No No No No Yes Yes <br /> Flintlastic SA Cap No Yes YeS Yes No Yes Yes <br /> See 5.5.1 <br /> Flintlastic SA Cap F No Yes No No No Yes Yes <br /> MetaLayment Yes No No No Yes Yes Yes <br /> Flintiastic GTA No Yes Yes Yes No Yes Yes <br /> See 5.5.1 <br /> Flintlastic GMS or Yes <br /> Premium GMS No Yes Yes No Yes Yes <br /> See 5.5.1 <br /> 5.5.1 "Foam-On Tile"is limited to use of the following Approved tile adhesives unless tensile adhesion/long term aging <br /> data from an accr dited testing laboratory is provided. <br /> 3M 2-Com onen Foam Roof Tile Adhesive AH-160 FL6332: Flintlastic SA Cap, Flintlastic GTA, Flintlastic GMS or Flintlastic <br /> Premium GMS. <br /> Dow TILE BONDTM Roof Tile Adhesive FL717: Flintlastic SA Cap,Flintlastic GMS or Flintlastic Premium GMS <br /> 5.6 Allowable substre es are noted below: <br /> 5.6.1 Direct-Bond to De k: <br /> WinterGuard HT, interGuard Sand,WinterGuard Granular or MetaLayment self-adhered to: <br /> D New or existing lywood <br /> ➢ ASTM D41 prim d new or existing plywood. <br /> Black Diamond B se, Fiintlastic SA PlyBase, Flintlastic SA Mid Ply, Flintlastic Ultra Glass SA, Flintlastic SA Cap or <br /> Flintlastic SA Cap R self-adhered to: <br /> ➢ New or existing lywood; <br /> � ASTM D41 or Fli tPrime SA primed new or existing plywood; <br /> � ASTM D41 or Fli Prime SA primed structurel concrete. <br /> Flintlastic GMS or lintlastic Premium GMS in hot asphalt to: <br /> ➢ ASTM D41 prim structurel concrete. <br /> Flintlastic GTA tor h-applied to: <br /> ➢ ASTM D41 prime structural concrete. <br /> 5.6.2 Wind Resistance r Underla ment 5 stems in Foam-On Tile A lications: FRSA/TRI April 2012 (04-12) does not <br /> address wind upli resistance of all underlayment systems beneath foam-on or mortar-set tile systems,where the <br /> underlayment for s part of the load-path. The following wind uplift limitations apply to underlayment systems that <br /> are not addressed in FRSA/TRI April 2012(04-12)and are used in foam-on or mortar-set tile applications. Maximum <br /> Design Pressure i the result of testing for wind load resistance based on allowable wind loads, and reflects the <br /> ultimate passing p essure divided by 2(the 2 to 1 margin of safety per FBC 1504.9 has already been applied).Refer to <br /> FBC 1609 for dete ination of design wind loads. <br /> 5.6.2.1 Maximum Desi n ressure=-240 sf: I <br /> Deck: Structurel concrete to meet project requirements to satisfaction of AHJ. I <br /> Primer: ASTM D41. <br /> ease Sheet: Black Diamond Base Sheet or Flintlastic Ultre Glass SA,self-adhered. � <br /> Underlayment: Flintlastic GTA,torch-applied or Flintlastic GMS or Flintlastic Premium GMS,applied in hot asphalt. ' <br /> 5.6.2.2 MaximumDesi n ressure=-555 sf: <br /> Oeck: Structurel concrete to meet project requirements to satisfaction of AHJ. <br /> Primer: ASTM D41 or FlintPrime SA. <br /> Base: (Optional)Flintlastic SA PlyBase or Flintlastic SA Mid Ply,self-adhered: <br /> Underlayment: Flintlastic SA Cap,self-adhered. <br /> Exterior Research and Design,LLC. Evaluation Report 11630.09.08-R34 <br /> Certificote oJAuthoriration Jt9503 FL11288-R13 I <br /> Revision 14:03/12/2015 <br /> Page 4 of 7 <br /> � <br />