16-17961 - Laserfiche WebLink

Browse Search

TRII'''JITY ER� 6.5.2 Fiintlastic GTA s al! 6e fully torch applied to the substrates noted in Section 5.6. Side {horizantal} ►aps shait be minimum 3-inch nd end (vertical) laps minimum 6-inch wide, and offset end-laps minimum 3 feet from course to course. Side and end-laps shall be fully heat-welded and inspected to ensure minimum 3/8-inch flow of modiflied compaunc3 6eyon the tap edge. 6.5.3 Tile shall be load and staged in a manner that prevents Yile slippage and/or damage to the underlayment. 6.5.4 Cansult CertainTe d instructions regarcting back-nailing requirements. 6.6 Flintlastic GMS o Flintlastic Premium GMS: 6.6.1 Flirrtlastic GMS a Ftintlastic Premium 6MS sFra(t be installed in compliance with current CertainTeed published installation requi ments. Far use in tile applications,reference is made to FRSA/TRI April 2012(04-12) Installation Manual,5th Editi n and Tabfe 1 herein. � 6.6.2 Flintlastic GMS or Fiintiastic Premium GMS shall be fully asphalt-applied to the su6strates noted in Section 5.6. Side (horizontal)laps s all be minimum 3-inch and end(vertical)laps minimum 6-inch wide,and offset end-laps minimum 3 faet from caurs to course. 5ide and end-laps shali be fully adhered in a wrnptete mopping of hat asphalt with asphalt extending approximately 3/8-inch beyond the lap edge. 6.6.3 Tite shal!be loade and staged in a manner that prevents tile slippage andjor damage ta the underlayment. 6.6.4 Consult CertainTe d instructions regarding back-nailing requirements. 6.? RooEsrs'Select: 6.7.1 Standard-Slo e A lication 4:12 and reater: Starting at the lower edge af the roof,apply a single layer af Roofers' Selec#parallel to he eaves,overhanging drip edge by'l:-inch. Overlap ends{vertical iaps}at least�-inch and sides {horizantaC laps) t(east 2-tnch. Offset end (aps from course to course at(east 6-feet.Appty flat and unwrinkied, fastening as requi ed to hold in place. 6.7.2 Cow Slo e A lica ion 2:12 u ta 4:12 : Starting at the lower edge of the roof,cover the entire deck by applying a double layer af R fers'Select parallel to the eaves. Begin by applying a 19-inch wide sterter strip of Roofers'Select along The eaves,o erlapping the drip edge by%-inch.P3ace a full-width sheet over the sYarter,with lower edge flush ta the starter's 1 er edge. Apply succeeding 36-inch wide courses up the roof slope, overlapping the previous course by 19-inch n'"shingle-fashion"'. Overlap ends at least 12-inch.Offset end laps from course to course at least 6-feet. Apply flat nd unwrinklecf,fastening as reyulred ta hold in p(ace. 6.7.3 Eaves Flashin f r Ice Dam Protection ell slo es : Eaves flashing may be constructed from self-adhering waterproofing un erlayment holding florida Product Appraval, ar by applying a doubfe layer of Roofers' Select cemented togethe with asphalt roofing cement(ASTM D 45$6,Type Ii}. Eaves flashing should be installed to a level of at least 24-inc inside the interior wall line, or in areas of severe icing, at least up to the highest water level expected to occur rom ice dams to the satisfactian of the Authority Flaving 3urisdiction. 7. BUILDING PERMIT REQUIREMEN 5: As required by ttce Building O cial or AuYhority Naving Jurisdiction in arder ta properly evaluate the installation of this product. $. MANUFACTURING PLANTS: Contact the manufacturer ar t e named QA entity for infarmation on pfants covered under Rule 61G20-3 QA requirements. 6. QUALI7YAS5URANCEENSITY': UL,LLC.—QUA9625;(414)248 409;karen.buchmann@ul.com -END OF EVAtUATlON REPORT- Eacterior Research and Design,ELC. Evaluatian Repork 1161d.09.88-R14 tertifurte o}Authorization 119503 FL11288-R13 Revision 14:03/12/2015 Fage 7 of T