16-17961 - Laserfiche WebLink

Browse Search

TRINITY E�� 5.6.3.5 Maximum Desi n Pressure=-105.0 sf: Deck: Min.19/32-inch plywood to meet project requirements to satisfaction of AHJ. ease Sheet: Flintlastic SA NailBase mechanically attached with 12 ga.,1%-inch long galvanized ring shank nails through 32 ga.,15/8-inch diameter tin caps spaced 4-inch o.c.at the min.2-inch laps and 4-inch o.c.at four(4)staggered rows in the field of the sheet. Base Ply: (Optional if top layer is Flintlastic SA Cap)Flintlastic SA PlyBase or Flintlastic SA Mid Ply,self-adhered. Underlayment: Flintlastic SA Cap,self-adhered. 5.7 Exposure Limitati ns: 5.7.1 Roofers'Select s all not be left exposed for longer than 30-days after installation. Refer to installation instructions specific to anticip ted exposure in Section 6. 5.7.2 Black Diamond B se,WinterGuard HT,WinterGuard Sand, WinterGuard Granular or MetaLayment shall not be left exposed for long than 180-days after installation. 5.7.3 Flintlastic SA Cap Flintlastic SA Cap FR, Flintlastic GTA, Flintlastic GMS or Flintlastic Premium GMS do not have an exposure limitati n,unless the prepared roof covering is to be adhesive-set tile atop Flintlastic SA Cap,GTA,GMS or Premium GMS,in hich case the maximum exposure is 180 days. 5.7.4 Flintiastic SA Nail ase, Flintlastic SA PlyBase, Flintlastic SA Mid Ply and Flinttastic Ultra Glass SA, for use as a base- layer in a multi-pl underlayment system,shall not be left exposed for longer than 30-days after installation,prior to placement of sub equent underlayment layer. 6 INSTALLATION: 6.1 CertainTeed Roo Underlayments shall be installed in accordance with CertainTeed published installation requirements sub ct to the Limitations set forth in Section 5 herein and the specifics noted below. 6.Z Re-fasten any loo e decking panels,and check for protruding nail heads. Sweep the substrate thoroughly to remove any dust and debr s prior to application,and primed the substrate(if applicable). 6.3 Flintlastic SA Nail ase Flintlastic SA PI Base Flintlastic SA Mid PI or Flintlastic Ultra Glass SA: 63.1 Flintlastic SA Nail ase, Flintlastic SA PlyBase and Flintlastic SA Mid Ply are limited to use as a base or mid-layer in multi-ply underla ent systems beneath Flintlastic SA Cap,Flintlastic SA Cap FR. 6.3.2 Flintlastic Ultre GI ss SA is limited to use as a base-layer in multi-ply underlayment systems beneath Flintlastic GTA, Flintlastic GMS or lintlastic Premium GMS. 6.3.3 Install the base-I yer underlayment to the substrates detailed in Section 5.6 in accordance with CertainTeed published installa ion instructions, followed by the final underlayment layer in accordance with the instructions outlined below fo the particular top-layer underlayment. 63.4 Roof cover limitati ns are those are those associated with the top-layer underlayment,set forth in Table 1. 6.4 Black Diamond Ba e Flintlastic SA Ca or SA Ca FR WinterGuard or MetaLa ment: 6.4.1 Shall be installed i compliance with current CertainTeed published installation requirements and FBC Section 1507 � for the type of pre ared roof covering to be installed. 6.4.2 For non-tile applic tions: 6.4.2.1 Shall be fully self- dhered to the substrates noted in Section 5.6. Side laps shall be minimum 4-inch and end-laps minimum 6-inch de,pressed firmly with a seam-roller,and offset end-laps minimum 2 feet from course to course. 6.4.2.2 Consult CertainTe d instructions for use of FlintBond SBS Modified Bitumen Adhesive, trowel grade, on the 6-inch end laps and T-sea detailing. 6.4.2.3 Consult CertainTe d instructions regarding back-nailing requirements. 6.43 For tile application (FlintlosticSA Cap,SA Cap FR onlyJ: 6.4.3.1 Reference is made o FRSA/TRI April 2012(04-12)Installation Manual and Table 1 herein. 6.4.3.2 Tile shall be loade and staged in a manner that prevents tile slippage and/or damage to the underlayment. 6.5 Flintlastic GTA: 6.5.1 Flintlastic GTA shal be installed in compliance with current CertainTeed published installation requirements. For use in tile applications reference is made to FRSA/TRI April 2012 (04-12) Installation Manual, 5th Edition and Table 1 herein. Exterior Research and Design,LLC. Evaluation Report 11610.09.08-R14 Certificate ofAuthorization q9503 FLi1288-R13 Revision 14:03/12/2015 Page 6 of 7