19-20813 - Laserfiche WebLink

Browse Search

AL 467 Swan Ave • Hohenwald,TN 38462 • (800) 284-7437 • www.olivertechnologi6s.com • Fax (931) 796-8811 OLIVER TECHNOLOGIES,INC. FLORIDA INSTALLATION INSTRUCTIONS FOR THE MODEL 1101 "V"SERIES ALL STEEL FOUNDATION SYSTEM MODEL 1101"V"(Steps 1-14) LONGITUDINAL ONLY:Follow Steps 1-9 LATERAL ONLY:Follow Steps 1-3 and Steps 10-14 ENGINEERS STAMP FOR CONCRETE APPLICATIONS:Follow Steps 15-18 ENGINEERS STAMP 1.SPECIAL CIRCUMSTANCES:If the following conditions occur-STOP!Contact Oliver Technologies at 1-8007-284-7437: a)Pier height exceeds 48" c)Roof eaves exceed 16" e)Location is within 1500 feet of coast b)length of home exceeds 76' d)Sidewall height exceed 96" INSTALLATION OF GROUND PAN 2.Remove weeds and debris in a6 approximate two foot.square.to expose firm soil for each ground pan(C). 3.Place ground pan(C)directly below chassis I-beam.Press or drive pan firmly into soil until flush or below soil then install pier per manufacturer's instructions or per Florida Regs. SPECIAL:NOTE:The longitudinal W"brace system may also serve as a pier under the home and should be loaded as any other pier. It is recommended that after leveling piers,and one-third inch(1/3")before home is Lowered completely on to piers,complete steps 4 through 9 below then remove jacks. INSTALLATION OF LONGITUDINAL"V"BRACE SYSTEM(Model 1101 L"V") NOTE:WHEN INSTALLINGTHE LONGITUDINAL SYSTEM ONLY,A MINIMUM OF 2 SYSTEMS PER FLOOR SECTION IS REQUIRED.SOILTEST PROBE SHOULD BE USED TO DETERMINE CORRECTTYPE OF ANCHOR PER SOIL CLASSIFICATION.IF PROBETEST READINGS ARE BETWEEN 175&275 A 5 FOOT ANCHOR MUST BE USED.IF PROBETEST READINGS ARE BETWEEN 276&350 A 4 FOOT ANCHOR MAY BE USED.USE GROUND ANCHORS WITH.DIAGONALTIES AND STABILIZER PLATES EVERY 5'4"-.VERTICAL TIES ARE ALSO REQUIRED ON HOMES SUPPLIED WITH VERTICALTIE CONNECTION POINTS(PER FLORIDA REG.). 4.Choose one of the approved longitudinal tube installations;either Diagram A or B.Then select the correct square tube(E)length from the diagram for appropriate pier height at support location or cut and drill 1.5"square tube to achieve appropriate length. PIER HEIGHT 1.25" 1.50" PIER HEIGHT 1.50" (400 Min.- 450 Max.) Tube Length Tube Length 9/16"Dia.(.562'1 hole 7 (40'Min.- 60°Max.) Tube Length 7 3/4 to 25" 22" 18" " 24 3/4'•to 32.1,/4"_.'::: 32 f. o.7s^ a... 18' ; .° _:. AE 1 . 18"to 25" 28' 33"to 41 �� 18" 24"to 39..",. 18..: ';::. . P 30"to 40" 44 DiagramA 0.75-� 36"to48."f,. Diagram B 5.Install(2)of the 1.50"square tubes(E)into the"U"bracket(J);insert carriage bolt and leave nut loose for final adjustment. 6.Place I-beam connector(F)loosely on the bottom flange of the I-beam. 7.(For Diagram A installation)Slide the selected 1.25"tube(E)into a 1.50"tube(E)and attach to I-beam connectors(F)and fasten loosely with bolt and nut.(For Diagram B installation)Attach the selected 1.5"tubes(E)to the I-beam connectors(F)and fasten loosely with bolts and nuts. 8.Repeat steps 6 through 7 to create the W"pattern of the-square tubes loosely in place. 9.Using standard hand tools tighten all nuts and bolts.(For Diagram A installation only,secure 1.25"and 1 .50"tubes using four(4) 1 /4"-14 x 3/4"self-tapping screws in pre-drilled holes.) INSTALLATION OF LATERAL TELESCOPING TRANSVERSE ARM SYSTEM(Model 1101 T"V") THE MODEL 1101 "V"(LONGITUDINAL&LATERAL PROTECTION)ELIMINATES THE NEED FOR STABILIZER PLATES&FRAME TIES. NOTE:THE USE OFTHIS SYSTEM REQUIRES VERTICALTIES SPACED AT 5'4'. FOUR FOOT(4')GROUND ANCHOR MAYBE USED EXCEPT WHERE THE HOME MANUFACTURER SPECIFIES DIFFERENT. 10.Install remaining vertical tie-down straps and 4'ground anchors per home manufacturer's instructions.NOTE:Centerline anchors to be sized according to soil torque condition.Any manufacturer's specifications for sidewall.anchor loads in excess of 4,000 lbs. require a 5'anchor per Florida Code. 11.Select the correct square tube brace(H)length for set-up lateral transverse at support location.The lengths come in either 60"or 72"lengths.(With the 1.50"tube as the bottom tube,and the 1.25"tube as the inserted tube.) 12. Install the 1.50 transverse brace(H)to the ground pan connector(D)with bolt and nut.' 13. Slide 1,25"transverse brace into the 1.50"brace and attach to adjacent I-beam connector(I)with bolt and nut. 14.Secure 1.50"transverse arm to 1.25"transverse arm using four(4) 1 /4"-14 x 3/4"self-tapping screws in pre-drilled holes. Page I PATENT#6634150&OTHER PATENT PENDING Revision 08/23/18