18-20581 - Laserfiche WebLink

Browse Search

Mandatory Requirements (as applicable) Mandatory requirements compiled by US Department of Energy and Pacific Northwest National Laboratory. Adopted with permission Topic Section Component Description Yes N/A exempt 1.To be checked by Designer or Engineer rvu,m Insulation 5.8.1.2 Envelope Below-grade wall insulation installed per manufacturers€TMs instructions. Insulation 5.8.1.2 Envelope Slab edge insulation installed per manufacturers El El ❑ €TMs instructions. Insulation 5.5.3.5 Envelope Slab edge insulation depthAength. Insulation 6.4.4.1.5 Envelope Bottom surface of floor structures incorporating radiant heating insulated to>=R-3.5. Fenestration 5.5.3.6 Envelope U-factor of opaque doors associated with the building thermal envelope meets requirements. SYSTEM—SPECIFIC 6.5.1,6.5.1.1, Mechanical Air economizers provided where required(and not 6.5.1.3,6.5.1.4 exempted),meet the requirements for design capacity,control signal,ventilation controls, high-limit shut-off,integrated economizer control, and provide a means to relieve excess outside air during operation. SYSTEM—SPECIFIC 6.5.1,6.5.1.2, Mechanical Water economizers provided where required, El 0 El 6.5.1.3 meet the requirements for design capacity, maximum pressure drop and integrated . economizer control. SYSTEM—SPECIFIC 6.5.1.5 Mechanical Economizer operation will not increase heating ❑ ❑ El energy use during normal operation. SYSTEM—SPECIFIC 6.5.2.2.1 Mechanical Three-pipe hydronic systems using a common return for hot and chilled water are not used. SYSTEM—SPECIFIC 6.5.2.2.3 Mechanical Hydronic heat pump systems connected to a common water loop meet heat rejection and heat addition requirements. SYSTEM—SPECIFIC 6.5.1.6 Mechanical Water economizer specified on hydronic cooling and humidification systems designed to maintain inside humidity at>35 A°F dewpoint if an economizer is required. SYSTEM—SPECIFIC 6.5.3.1.1 Mechanical HVAC fan systems at design conditions do not El E exceed allowable fan system motor nameplate hp or fan system bhp. SYSTEM—SPECIFIC 6.5.3.1.2 Mechanical HVAC fan motors not larger than the first available El 0 motor size greater than the bhp. HVAC 6.5.6.1 Mechanical Exhaust air energy recovery on systems meeting El 0 El Tables 6.5.6.1-1,and 6.5.6.1-2. SYSTEM—SPECIFIC 7.4.2 Mechanical Service water heating equipment meets efficiency requirements. SYSTEM—SPECIFIC 7.5.2 Mechanical Service water heating equipment used for space heating complies with the service water heating equipment requirements. Insulation 5.8.1-2 Envelope Above-grade wall insulation installed per manufacturers€TMs instructions. Insulation 5.8.1.2 Envelope Floor insulation installed per manufacturera€TMs instructions. Controls 10.4.3 Mechanical Elevators are designed with the proper lighting, El Q ED ventilation power,and standby n lbde. SYSTEM—SPECIFIC 6.4.1.1,6.8.1-7a Mechanical Heat Rejection Equipment:Minimum Efficiency Requirement Table 6.8.1-7 SYSTEM—SPECIFIC 6.4.1.1,6.8.1-7b Mechanical Heat Rejection Equipment:Minimum Efficiency Requirement Table 6.8.1-7 SYSTEM—SPECIFIC 6.4.1.1,6.8.1-7c Mechanical Heat Rejection Equipment:Minimum Efficiency L1- 0 RequirementTable 6.8.1-7 EnergyGauge Summit®Fla/Com-2017.TAM 2017-1.0 Compliant Software.Effective Date: Dec 31,2017 Florida Building Code,Sixth Edition(2017)-Energy Conservation ASHRAE 90.1-2013-Prescriptive Compliance Option 7/6/2018 Page 8 of 21