19-21343 - Laserfiche WebLink

Browse Search

3. To be checked by Inspector Insulation C303.1 Envelope Roof insulation installed per manufactureraETms ❑ ❑ ❑ instructions. Blown or poured loose-fill insulation is installed only where the roof slope is<=3 in 12. Insulation C303.1 Envelope Building envelope insulation is labeled with ❑ R-value or insulation certificate providing R-value and other relevant data. Fenestration C303.1.3 Envelope Fenestration products rated in accordance with 0 ❑ NFRC. Fenestration C303.1.3 Envelope Fenestration products are certified as to ❑ performance labels or certificates provided. Insulation C303.2,C402.2.4 Envelope Floor insulation installed per manufacturer's ❑ ❑ ❑ instructions.Cavity or structural slab insulation installed in permanent contact with underside of decking or structural slabs. Insulation C303.2.1 Envelope Exterior insulation protected against damage, ❑ sunlight,moisture,wind,landscaping and equipment maintenance activities. Insulation C303.2.1 Envelope Exterior insulation is protected from damage with ❑ ❑ a protective material.Verification for exposed foundation insulation may need to occur during Foundation Inspection. Insulation C402.1.3 Envelope Non-swinging opaque doors have R-4.75 0 ❑ ❑ insulation. Insulation C402.2.2 Envelope Skylight curbs are insulated to the level of roofs with insulation above deck or R-5. Insulation C402.2.2 Envelope Insulation intended to meet the roof insulation requirements cannot be installed on top of a suspended ceiling.Mark this requirement compliant if insulation is installed accordingly. Air Leakage C402.5 Envelope Building envelope contains a continuous air ❑ ❑ ❑ barrier that has been tested and deemed to limit air leakage<=0.40 cfm/ft2. Air Leakage C402.5.1 Envelope The building envelope contains a continuous air ❑ barrier that is sealed in an approved manner and either constructed or tested in an approved manner. Air barrier penetrations are sealed in an approved manner. Air Leakage C402.5.1.1 Envelope All sources of air leakage in the building thermal envelope are sealed,caulked,gasketed,weather stripped or wrapped with moisture vapor-permeable wrapping material to minimize air leakage. Air Leakage C402.5.1.2.1 Envelope The building envelope contains a continuous air barrier that is sealed in an approved manner and material permeability<=0.004 cfm/ft2. Air barrier penetrations are sealed in an approved manner. Air Leakage C402.5.1.2.2 Envelope The building envelope contains a continuous air ❑ barrier that is sealed in an approved manner and average assembly air leakage—0.04 cfm/ft2. Air barrier penetrations are sealed in an approved manner. Air Leakage C402.5.2,C402.5.4 Envelope Factory-built fenestration and doors are labeled ❑ ❑ as meeting air leakage requirements. Air Leakage C402.5.3 Envelope Where open combustion air ducts provide combustion air to open combustion fuel burning appliances,the appliances and combustion air opening are located outside the building thermal envelope or enclosed in a room,isolated from inside the thermal envelope Air Leakage C402.5.5, Envelope Stair and elevator shaft vents have motorized ❑ C403.2.4.3 dampers that automatically close. Air Leakage C402.5.5, Envelope Outdoor air and exhaust systems have motorized ❑ ❑ C403.2.4.3 dampers that automatically shut when not in use and meet maximum leakage rates.Check gravity dampers where allowed. Air Leakage C402.5.6 Envelope Weatherseals installed on all loading dock cargo ❑ doors. EnergyGauge Summit®Fla/Com-2017.TAM 2017-1.0 Compliant Software.Effective Date:Dec 31,2017 Florida Building Code,Sixth Edition(2017)-Energy Conservation IECC 2015-Total Building Performance Compliance Option 10/5/2018 Page 12 of 22