19-21343 - Laserfiche WebLink

Browse Search

Air Leakage C402.5.8 Envelope Recessed luminaires in thermal envelope to limit ❑ infiltration and be IC rated and labeled.Seal between interior finish and luminaire housing. HVAC C403.2.1 Mechanical HVAC systems and equipment design loads ❑ 13 ❑ calculated in accordance with ANSI/ASHRAE/ACCA Standard 183 or by an approved equivalent computational procedure SYSTEM—SPECIFIC C403.2.10 Mechanical HVAC piping insulation thickness. Where piping ❑ ❑ is installed in or under a slab,verification may need to occur during Foundation Inspection. HVAC C403.2.3 Mechanical HVAC equipment efficiency verified. 0 0 ❑ SYSTEM—SPECIFIC C403.2.3 Mechanical PTAC and PTHP with sleeves 16 in.by 42 in. labeled for replacement only as per Footnote b to Table C403.2.3(3). SYSTEM—SPECIFIC C403.2.4.1 Mechanical Heating and cooling to each zone is controlled by ❑ ❑ a thermostat control. Minimum one humidity control device per installed humidification/dehumidification system. SYSTEM—SPECIFIC C403.2.4.1.1 Mechanical Heat pump controls prevent supplemental electric resistance heat from coming on when not needed. HVAC C403.2.4.1.2 Mechanical Thermostatic controls have a 5 A°F deadband. ❑ ❑ HVAC C403.2.4.1.2 Mechanical Thermostatic controls have a 5 A°F deadband. HVAC C403.2.4.1.3 Mechanical Temperature controls have setpoint overlap restrictions. HVAC C403.2.4.2.1, Mechanical Automatic Controls:Setback to 55°F(heat)and 0 ❑ C403.2.4.2.2 85°F(cool);7-day clock,2-hour occupant override,10-hour backup SYSTEM—SPECIFIC C403.2.4.2.3 Mechanical Systems include optimum start controls. HVAC C403.2.4.5, Mechanical Snow/ice melting system sensors for future C403.2.4.6 connection to controls.Freeze protection systems have automatic controls installed. HVAC C403.2.6.2 Mechanical Enclosed parking garage ventilation has ❑ ❑ automatic contaminant detection and capacity to stage or modulate fans to 50%or less of design capacity. HVAC C403.2.9 Mechanical HVAC ducts and plenums insulated. Where ducts or plenums are installed in or under a slab, verification may need to occur during Foundation Inspection. SYSTEM—SPECIFIC C403.2.9.1.3 Mechanical Ductwork operating>3 in.water column requires air leakage testing. SYSTEM—SPECIFIC C403.4.1.2 Mechanical VAV fans have static pressure sensors located so 13 ❑ ❑ controller setpoint<=1.2 w.c.. SYSTEM—SPECIFIC C403.4.2.2 Mechanical Two-pipe hydronic systems using a common distribution system have controls to allow a deadband>=15°F,allow operation in one mode for at least 4 hrs before changeover,and have rest controls to limit heating and cooling supply temperature to<=30 OF. SYSTEM—SPECIFIC C403.4.2.3.3 Mechanical Two-position automatic valve interlocked to shut ❑ El El off water flow when hydronic heat pump with pumping system>10 hp is off. SYSTEM—SPECIFIC C403.4.4.5, Mechanical Zone controls can limit simultaneous heating and ❑ ❑ ❑ C403.4.4.5.1-4 cooling and sequence heating and cooling to each zone. SYSTEM—SPECIFIC C403.4.5 Mechanical Condenser heat recovery system that can heat water to 850F or provide 60%of peak heat rejection is installed for preheating of service hot water. SYSTEM—SPECIFIC C403.4.6 Mechanical Hot gas bypass limited to: ❑ <=240 kBtu/h-50%capacity, >240 kBtu/h -25%capacity SYSTEM—SPECIFIC C404.3 Mechanical Heat traps installed on non-circulating storage ❑ ❑ water tanks. EnergyGauge Summit®Fla/Com-2017.TAM 2017-1.0 Compliant Software.Effective Date:Dec 31,2017 Florida Building Code,Sixth Edition(2017)-Energy Conservation IECC 2015-Total Building Performance Compliance Option 10/5/2018 Page 13 of 22