Laserfiche WebLink
FLASHING MEMBRANE ADHESIVE <br /> PAA 0 21 PLASTIC CEMENT f siplast <br /> Commercial Product Data Sheet <br /> Product Description COMMERCIAL PRODUCT INFORMATION <br /> PA-1021 Plastic Cement is a general purpose roof cement Unit: 5-Gallon Pail <br /> produced from refined asphalt and petroleum solvents with 4.7 gallons(17.8 liters)net content <br /> non-asbestos fibers added for reinforcement. PA-1021 is an <br /> all-weather grade plastic cement and is specifically formulated Coverage <br /> to be compatible with Siplast roofing membranes. Smooth low absorptive <br /> substrates: 1%-2 gal/sq (0.5-0.8 L/W) <br /> Product Uses Irregular substrates: 2-3 gal/sq (0.8-1.2 Um') <br /> PA-1021 Plastic Cement is specially designed for use with <br /> guaranteed Siplast Roofing Systems as a mastic for setting all Thickness @ 1%gaVsq: 20 mils (0.5 mm) <br /> metal flanges and drain lead flashings and for making Thickness @ 3 gaVsq: 48 mils (1.2 mm) <br /> temporary repairs to the roofing membrane. PA-1021 can also wet film gauge wet film gauge <br /> be used as a flashing adhesive on flat or low slope <br /> applications, where slumping is not a concern. It is highly Coverage Weight <br /> flexible, has a trowelling consistency, and may be applied with @ 1%gaVsq coverage: 16 lb/square (0.8 kg/m2) <br /> a trowel or putty knife to dry,clean surfaces. @ 3 gal/sq coverage: 39 lb/square (1.9 kg/m� <br /> wet film weight wet film weight <br /> PA-1021 Plastic Cement can be applied using a standard <br /> trowel. Applications over irregular or porous substrates may Flash Point,Cleveland Open Cup: >102`F min. (39`C) <br /> require an approximate total of 2 to 3 gallons per square. <br /> Coverage rate may vary depending on ambient temperature, Recommended minimum adhesive temperature for application: <br /> surface conditions,and applicator. 70-F(21-C). <br /> Temperature Considerations and Limitations <br /> In ambient temperatures below 40°F(4°C),materials should be Packaging: The pails are stacked three high on pallets and <br /> stored in a warm environment in order to obtain the minimum stretch wrapped. <br /> desired material temperature of 70°F (21°C) at the point of <br /> application. Membrane materials should be stored in a warm Pallet: 45 in X 48 in(114 cm X 122 cm)wooden pallet. <br /> place prior to application in order to facilitate proper installation Number Pails Per Pallet: 42 <br /> and avoid wrinkling and buckling. Additionally, rolls may be Number Pallets Per Truckload: 22 <br /> unrolled and relaxed and/or precut. Weight Per Pail: 51 lb (23 kg) <br /> ProductApprovais Shipping Classification: White Label(combustible) <br /> PA-1021 Plastic Cement.me_ets or exceeds the requirements of; <br /> (ASTM:D 4586_Type II for asbestos free, asphalt based roof Storage and Handling: All containers of PA-1021 Plastic <br /> i.cement. Cement should be stored upright on a clean,flat surface. Care <br /> should be taken that containers are not dropped and container <br /> PA-1021 Plastic Cement meets current regional VOC seals are not broken prior to use. All containers should be <br /> regulations. stored in a dry place, out of direct exposure to the elements, <br /> and should be kept away from excessive heat, fire or open <br /> VOC content: This product contains an average 177 gA VOC. I flames. <br /> Current copies of all Siplast Commercial Product Data Sheets are MEMBRANE ADHESIVE FOR <br /> posted on the Siplast Web site at www.Siplast.com. PEKE- RATION FLASHING$ <br /> Rev 5/2018 <br /> Siplast 1000 Rochelle Blvd. 201 Bewicke Ave.,Suite 208 Customer Service in North America <br /> Irving,TX 75062-3940 North Vancouver,BC,Canada V7M 3M7 1.800.922.8800 www.slplast.com <br />