Laserfiche WebLink
Typical Wiring (GSA-10) <br /> Modules will accept#18 AWG to#12 AWG(0,75MM2 to 2,50mmg wire sizes.Note: Sizes#16 AWG(1.0mm2)and#18 AWG(0.75mm2) <br /> are preferred for ease of installation. See Signature Loop Controller catalog sheet for detailed wiring requirement specifications, <br /> Input/Output Module (personality codes 31 -40) <br /> Wiring Notes: <br /> N.C.or N.G. & Maximum 25 Ohm resistance per wire. <br /> Ll N.O.or N.G. UUULC <br /> Listed #12 AWG(2.5 mml max;018 AWG(0.762)mm min. <br /> 47 kW <br /> EOL Zis 10 Vdc @ 350 mA,max. <br /> See the loop controller installation sheet for wiring <br /> AAAA specifications. <br /> Input/Output Module System programming determines whether contact <br /> TB2 will be normally-open(N/0)or normally-closed(N/C). <br /> 8 7 6 5 Supervised and power-limited. <br /> 0 0 0 <br /> zE Power-Grafted unless connected to a nonpower- <br /> Red LED(Active/AJar Green LED(NormalfTrouble) limited source.If the source is nonpower-limfted, <br /> A Jar Input/ <br /> Output rG,i.&en LED(TNO.i <br /> 0 0 eliminate the power-limited mark and: <br /> 1 . Maintain a 1/4-inch(6.4 rnm)space from power- <br /> 4 3 2 limited erring. <br /> T81 or <br /> • Use FPL,FPLR,FPLR or an equivalent cable in <br /> AAALt accordance with the National Electric Code. <br /> (+) t I The Nomex isolation barrior separates power-limited <br /> From loop controller Data In Data out To next device and nonpower-limited wiring.Watch out for the sharp <br /> Data <br /> out(.,I <br /> or previous device Data in Data out(+)I corners during Installation and maintenance. <br /> Typical Wiring (GSA-MIO) <br /> Modules will accept#12 AWG(2.5mm2),#18 AWG(0.75mM2), #16(1.0MM2),and#14 AWG (1.50mM2)wire sizes.Note:Sizes#16 AWG <br /> (1.0mm2)and#18 AWG(0.75MM2)are preferred for ease of installation.See Signature Loop Controller catalog sheet for detailed wiring <br /> requirement specifications. <br /> Input/Output Module (personality codes 31 -40) <br /> Wiring Notes: <br /> ZL Maximum 26 Ohm resistance per wire.Maximum <br /> > T81 through T86 circuit capacitance of 0.1 mF. <br /> Green LED!(NormalfrrMilble Input/Output Module C 10 Vdc @ 350 mA,max. <br /> Red LED(Active/Al 1234 <br /> 1 1 U102R or U106R motherboard See the Signature loop controller installation sheet for <br /> ASA wiring specifications. <br /> Data In ZL Supervised and power-limited <br /> 0 uL/uLc listed 47 kW EOL <br /> Data 4 0 <br /> 3 <br /> Circuit 2 0 System programming determines whether contact <br /> 1 T87 will be normally-open(IN/0)or normally-closed(N/Q. <br /> Data Out+ Power-limited unless connected to a nonpower- <br /> & 4 Nol"ections required limited source.If the source is nonpower-limited, <br /> - 3 for M connections other modules eliminate the power-limited mark and: <br /> 2 May require connections. Maintain a 1/4-Inch(6.4 mm)space from power- <br /> TB15 limited wiring. <br /> PO <br /> �Remove motherboard Jumpers. or <br /> • Use FPL,FPLR,FPUP or an equivalent cable in <br /> TE18 through T81 3-� 1234 accordance with the National Electric Code. <br /> 8 See the U102R or U106R Installation sheet for <br /> additional instructions about the separation of power- <br /> Dry contact relay limited and nonpower-limited wiring. <br /> Page 4 of 6 D A")A 5 H r ET K85001-0533 <br /> r k,j 1r, t)c7 ir_,, Issue 1 <br />