20-22223 - Laserfiche WebLink

Browse Search

Signature Series Overview The Signature Series intelligent analog-addressable system from Kidde is Fast Stable Communication-Built-in intelligence means less informa- an entire family of multi-sensor detectors and mounting bases,multiple- tion needs to be sent between the device and the Signature Data Controller function input and output modules,network and non-network control (SDC).Other than regular supervisory polling response,Signature devices panels,and user-friendly maintenance and service tools.Analog informa- only need to communicate with the SDC when they have something new tion from equipment connected to Signature devices is gathered and con- to report.This provides very fast control panel response and allows a lower verted into digital signals.An onboard microprocessor in each Signature baud rate(speed)to be used for communication on the circuit.The lower device measures and analyzes the signal and decides whether or not to baud rate offers several advantages including: input an alarm.The microprocessor in each Signature device provides four additional benefits-Self-diagnostics and History Log,Automatic Device - Less sensitivity to circuit wire characteristics. Mapping,and Fast,Stable Communication. - Less sensitivity to noise glitches on the cable. Self-diagnostics and History Log-Each Signature Series device con- - Less emitted noise from the data wiring. stantly runs self-checks to provide important maintenance information.The results of the self-check are automatically updated and permanently stored -Twisted or shielded wiring is not required. in its non-volatile memory.This information is accessible for review any Diagnostic LEDs-Twin LEDs on most Signature devices provide visual time at the control panel,PC,or using the SIGA-PRO Signature Program/ indication of normal and alarm-active conditions.A flashing green LED Service Tool. shows normal system polling.A flashing red LED means the module is Automatic Device Mapping-The Signature Data Controller(SDC)learns in alarm-active state.Both LEDs on steady indicates alarm-active state- where each device's serial number address is installed relative to other de- standalone mode. vices on the circuit.The SDC keeps a"map"of all Signature Series devices Testing&Maintenance-Automatic self-diagnosis identifies when a connected to it.The Signature Series Data Entry Program also uses the Signature device is defective and causes a trouble message.The user- mapping feature.With interactive menus and graphic support,the wired cir- friendly maintenance program shows the current state of each device and cults between each device can examined.Layout or"as-built"ctaps),device types ann drawingd their address other pertinent information.Single devices may be turned off temporarily,from information showing branch wiring the control panel.Scheduled maintenance(Regular or Selected)for proper are stored on disk for printing hard copy.This takes the mystery out of the system operation should be planned to meet the requirements of the Authority installation.The preparation of"as built"drawings is fast and efficient. Having Jurisdiction(AHJ).Refer to current NFPA 72 and ULC CAN/ULC Most Signature modules use a"personality code"selected by the installer 536 standards. to determine their actual function.Personality codes are downloaded quality and Reliability-Kidde Signature devices are manufactured in from the SDC during system configuration and are indicated during North America to strict international ISO 9001 standards.All electronics uti- device mapping. lize surface mount technology(SMT)for smaller size and greater immunity to RF noise.A conformal coating is used for humidity and corrosion resistance. Specifications Model GSA-10 GSA-MIO Description Standard Mount Input/Output Module Plug-in(UIO)Input/Output Module North American 2'/2 inch(64 mm)deep one-gang boxes Mounting and 11/2 inch(38 mm)deep 4 inch square boxes with one- Plugs into U102R or U106R Motherboards only. gang covers and GSA-MP mounting plates Current Standby I 250 pA Activated 430 pA _Relay type Form A or B Contact ratings(pilot duty) _ 24 Vdc:2 A._120 Vac:0.5 A (Not rated for capacitive loads.) T Initiating Device Circuit EOL(end-of-line)resistor UL/ULC listed 47k Ohm Max.circuit resistance 50 Ohm(25 Ohms per wire) Max.circuit capacitance 1 0.1 pF -Wiring Terminations i Suitable for#12 to#18 AWG (2.5 mm2 to 0.75mm2) Personality Codes Ten Selectable Codes Available _Address Requirements ; Uses One Module Address Operating Voltage ! 15.2 to 19.95 Vdc(19 Vdc nominal) Construction High Impact Engineering Polymer Environment Operating Temperature 32°F to 120°F(0°C to 49°C) Storage Temperature i -4°F to 140'F(-20°C to 60'C) Humidity j _ 0 to 93%RH LED Operation On-board Green LED-Flashes when polled;On-board Red LED-Flashes when in alarm/active Compatibility Use GSA-10 and GSA-MIO with:Signature Loop Controller Plug GSA-MIO into:U106R or U102R Motherboards Agency Listings UL,ULC,MEA,CSFM Page 5 of 6 Cl A I A SHEET K85001-0533 W-1 io :'x: tor snl't;o irOint,j1U r;?08 Bf1. issue 1