|
io
<br />F�OCIFTCIF LA I T SCHEDULE
<br />MARK
<br />MANUFACTURER
<br />MODEL
<br />AIRFLOLL
<br />OUTSIDE AIF
<br />AM51ENI
<br />EXT. SP
<br />DX COOLING COIL
<br />ELECTRIC
<br />HEAT
<br />ELECTRICAL
<br />(CFM)
<br />(CFM)
<br />(OAT)
<br />C IN. W.C. )
<br />EAT
<br />TOTAL
<br />SENSIBLE
<br />INPUT
<br />OUTPUT
<br />V , PH , HZ
<br />MCA
<br />MOCP
<br />EER
<br />AF'P@O�XXIIM ATE
<br />REMARKS
<br />( DB/WB)
<br />l BTU/H)
<br />l BTU/H)
<br />KW)
<br />(1'1BH)
<br />HP
<br />(SEER)��
<br />RTU-1
<br />YORK
<br />ZJ060E20
<br />2000
<br />440
<br />105
<br />0.15
<br />80/61
<br />60,000
<br />39,000
<br />20
<br />68
<br />480/3/60
<br />33B
<br />35
<br />13.00
<br />1150
<br />1-5
<br />RTU-5
<br />STD
<br />RTU-2
<br />YORK
<br />ZJ04SE15
<br />1600
<br />352
<br />105
<br />0.15
<br />80/61
<br />48000
<br />35,000
<br />15
<br />51
<br />480/3/60
<br />263
<br />30
<br />13.00
<br />1060
<br />1-5
<br />STD
<br />RTU-3
<br />RTU-4
<br />YORK
<br />ZJ15OE24N
<br />5000
<br />1100
<br />105
<br />0.15
<br />80/6l
<br />110,000
<br />121,000
<br />24
<br />82
<br />48S13D/60
<br />42.1
<br />45
<br />11.00
<br />1560
<br />1-5
<br />RTU-6
<br />RTU-1
<br />RTU-8
<br />YORK
<br />ZJ120EIS
<br />4000
<br />264
<br />105
<br />0.15
<br />80/6l
<br />120,000
<br />90,000
<br />18
<br />62
<br />48S/,3D/60
<br />313
<br />35
<br />11-00
<br />130S
<br />1-5
<br />RTU-8
<br />YORK
<br />ZJ036EO5
<br />1200
<br />264
<br />105
<br />0.15
<br />80/6-1
<br />3fo,000
<br />2-1,000
<br />5
<br />17
<br />4W13D/60
<br />12.8
<br />15
<br />13.00
<br />1000
<br />1-5
<br />ST
<br />ACCESSORIES:
<br />A. 110V DUPLEX WATER PROOF MAINTENANCE RECEPTACLE. SMOKE DETECTOR-
<br />5. NOVAR CONTROLS - FIELD INSTALLED BY NOVAR CONTROLS CONTRACTOR BY TJX.
<br />NOTES:
<br />1. CONTRACTOR IS TO PROVIDE AND INSTALL ROOF TOP UNIT AND 14' HIGH FACTORY FABRICATED ROOF CURB.
<br />2. CONTRACTOR IS TO PROVIDE 1' FARR 30/30 FILTERS, OR EQUAL, ON ALL RTU'S .
<br />3. UNITS COME WITH A 5 MINUTE TIME DELAY ON COMPRESSOR START.
<br />4. SET 2 POSITION OUTSIDE AIR DAMPER WITH MINIMUM POSITION AS SPECIFIED ABOVE . OUTSIDE AIR
<br />DAMPER SHALL FULLY
<br />CLOSE UPON UNIT SHUTDOWN .
<br />5. PROVIDE TEMPORARY THERMOSTAT.
<br />6. PROVIDE AND INSTALL CO2 SENSORS.
<br />1. PROVIDE -AND INSTALL 18/10 T'STAT CABLE FOR SENSOR
<br />IDIFFUeEfR,
<br />MARK
<br />MANUFACTURER
<br />MODEL
<br />TYPE
<br />NECK SIZE
<br />(L' x W')
<br />FACE SIZE
<br />(L' x W')
<br />FRAME TYPE
<br />NC
<br />REMARKS
<br />A
<br />TITUS
<br />TMS
<br />SQUARE SUPPLY DIFFUSER
<br />PER PLAN
<br />24'x24'
<br />TYPE 3
<br />30
<br />WHITE
<br />5
<br />TITUS
<br />TMS
<br />SQUARE SUPPLY DIFFUSER
<br />PER PLAN
<br />24'x24'
<br />TYPE 1
<br />30
<br />WHITE
<br />C
<br />TITUS
<br />300FL
<br />RECTANGULAR SUPPLY DIFFUSER
<br />PER PLAN
<br />12'x6'
<br />TYPE 1
<br />30
<br />WHITE . PROVIDE BOOT W/ SQUARE
<br />TO ROUND TRANSITION.
<br />D
<br />TITUS
<br />TMS
<br />SQUARE SUPPLY DIFFUSER
<br />PER PLAN
<br />12'xl2'
<br />TYPE 3
<br />30
<br />WHITE
<br />E
<br />TITUS
<br />50F
<br />EGGGRATE RETURN GRILL
<br />PER PLAN
<br />24'x24'
<br />TYPE 3
<br />30
<br />WHITE
<br />F
<br />TITUS
<br />350 RL
<br />RECTANGULAR RETURN AIR GRILL
<br />PER PLAN
<br />14'x14'
<br />TYPE 1
<br />30
<br />WHITE. PROVIDE BOOT W/ SQUARE
<br />TO ROUND TRANSITION.
<br />G
<br />TITUS
<br />50F
<br />EGGCRATE EXHAUST GRILL
<br />PER PLAN
<br />16'x16'
<br />PER PLAN
<br />30
<br />WHITE
<br />H
<br />RTS
<br />510-50
<br />CONCENTRIC SUPPLY/RETURN
<br />(2) 18'x32'
<br />48'x42'
<br />PER PLAN
<br />30
<br />WHITE
<br />ELECTRIC LAIT
<br />HEATED
<br />MARK
<br />MANUFACTURER
<br />MODEL NO.
<br />KW IN
<br />BTUH OUT
<br />VOLTS/PHASE
<br />REMARKS
<br />EUH-1
<br />MARKEL
<br />P31FI5130CA1N
<br />20 KW
<br />68200
<br />480/3
<br />VERTICAL MOUNT WITH
<br />WALL/CEILING BRACKET
<br />EXHAJ5T FAN SCHEDJLE
<br />MARK
<br />MANUFACTURER
<br />MODEL
<br />AIRFLOW
<br />(CFM)
<br />EXT. SP
<br />(IN W.G.)
<br />V , PH , HZ
<br />MOTOR
<br />SIZE (HP)
<br />EF-1
<br />COOK
<br />90SQN10D
<br />250
<br />25'
<br />120/1/60
<br />1/6
<br />Er--2
<br />COOK
<br />90SQNIOD
<br />200
<br />.25'
<br />120/1/60
<br />1/6
<br />EF-3
<br />COOK
<br />120C13D
<br />1095
<br />25'
<br />120/1/60
<br />1/4
<br />EF-4
<br />COOK
<br />90SQN10D
<br />250
<br />25'
<br />120/1/60
<br />1/6
<br />aDUCT I-4aNG3
<br />SCALE. -NONE
<br />L ROOF JOIST
<br />__----HANGER WIRE
<br />SHEET MTL. DUCT HANGER
<br />RECTANGULAR DUCT
<br />EXTERNAL INSULATION SHALL
<br />BE RUN CONTINUOUS THRU
<br />HANGERS
<br />IMPORTANT NOTICE:
<br />STANDARD LEADTIME FOR YORK RTU HVAC EQUIPMENT IS FOUR (4) WEEKS
<br />MANUFACTURING PLUS ONE (1) WEEK TRANSPORTATION DEPENDING ON THE
<br />LOCATION IN THE 48 STATES. ANY NON STANDARD OPTION MAY ADD TO
<br />THE STANDARD MANUFACTURING LEADTIME AND WILL BE CONFIRMED AT
<br />PLACEMENT OF ORDER HVAC EQUIPMENT WITH FACTORY TECHNICOAT
<br />COATING OF CONDENSER COILS WILL HAVE AN ELEVEN (I1) WEEK
<br />LEADTIME.
<br />'G- ROOF JOIST
<br />------HANGER WIRE
<br />SHEET MTL. DUCT HANGER
<br />SPIRAL DUCT
<br />__-----EXTERNAL INSULATION SHALL
<br />BE RUN CONTINUOUS THRU
<br />HANGERS
<br />ROUND DUCT HANCsER DETAIL',
<br />Z SGALE:NgJE '
<br />2' WIDE MIN. DUCT STRAP
<br />48' O.G. MAX.
<br />RIGID ROUND METAL DUCT
<br />EXTERNALLY INSULATED
<br />RIGID ROUND DUCT ELBOW
<br />EXTERNALLY INSULATED
<br />INSULATED FLEXIBLE DUCT
<br />MAX. LENGTH 5'-0'
<br />FIRE DAMPER
<br />(LOCATION WHE
<br />REQUIRED) I
<br />VOLUME DAMPER
<br />(FOR FINAL BALANCE
<br />ADJUSTMENT)- .
<br />aHVAC D
<br />SCALE -NONE
<br />DIFFUSER
<br />SPIN -IN FITTING-/
<br />WITH BALANCING DAMPER
<br />AND 457 EXTRACTOR
<br />(DAMPER USED FOR
<br />ROUGH BALANCING)
<br />IL ING
<br />UCTUJOfR< DETAIL
<br />METAL SUPPLY DUCT
<br />EXTERNALLY INSULATED
<br />GENERAL
<br />A. THE GENERAL CONDITIONS OF THE GENERAL SPECIFICATIONS, ALONG
<br />WITH ALL APPLICABLE INSTRUCTIONS TO BIDDERS, SHALL FORM A
<br />PART OF THIS SECTION OF THE SPECIFICATIONS.
<br />B. REFERENCE IS MADE TO REQUISITES FOR BIDDERS AND CONTRACTORS
<br />UNDER OTHER SECTIONS OF THESE SPECIFICATIONS, WHICH SHALL
<br />BE CONSIDERED BINDING, UNLESS OTHERWISE NOTED UNDER THIS
<br />SECTION.
<br />.SCOPE
<br />EACH CONTRACTOR SHALL THOROUGHLY ACQUAINT HIMSELF WITH THE
<br />CONSTRUCTION DETAILS, BOTH ON TENANT CONSTRUCTION DRAWINGS AND
<br />LANDLORD'S AS REFERRED TO, BEFORE SUBMITTING HIS BID AS NO
<br />ALLOWANCES WILL BE MADE BECAUSE OF CONTRACTOR'S UNFAMILIARITY
<br />WITH THESE DETAILS. ALL PERFORMANCE OF CONSTRUCTION SHALL BE
<br />AS REQUIRED BY THE PACE OF THE GENERAL CONSTRUCTION.
<br />INSPECTION OF SITE
<br />ALL PROPOSALS SHALL PRECLUDE THAT CONTRACTOR IS FAMILIAR WITH
<br />J0551TE CONDITIONS AND UTILITY LOCATIONS AND THE LACK OF SPECIFIC
<br />INFORMATION ON THE DRAWINGS SHALL NOT RELIEVE THE CONTRACTOR
<br />OF ANY RESPONSIBILITY.
<br />PERMITS
<br />ALL PERMITS AND LICENSES NECESSARY FOR THE PROPER EXECUTION
<br />OF THE WORK SHALL BE SECURED AMC) PAID FOR BY THE SUBCON-
<br />TRACTOR INVOLVED.
<br />CODE REQUIREMENTS
<br />ALL WORK UNDER THIS CONTRACT SHALL COMPLY WITH THE PROVISIONS
<br />OF THE SPECIFICATIONS, DRAWINGS OR AS DIRECTED BY THE OWNER,
<br />AND SHALL SATISFY ALL APPLICABLE CODES, ORDINANCES, AND/OR
<br />REGULATIONS OF THE GOVERNING BODIES, WHETHER SO SHOWN OR NOT,
<br />AMC) ALL MODIFICATIONS REQUIRED BY SUCH AUTHORITIES SHALL BE
<br />MADE BY THE CONTRACTOR WITHOUT ANY ADDITIONAL COST TO OWNER
<br />MATERIALS AMC) WORKMANSHIP
<br />A. ALL MANUFACTURED ARTICLES, MATERIALS, AMC) EQUIPMENT SHALL
<br />BE APPLIED AS RECOMMENDED BY THE MANUFACTURERS, AND UN-
<br />LESS OTHERWISE SPECIFIED SHALL BE NEW, AND FREE FROM ANY
<br />AND ALL DEFECTS. LIKE MATERIALS USED SHALL BE OF THE SAME
<br />MANUFACTURE AND QUALITY UNLESS OTHERWISE SPECIFIED.
<br />B. ALL WORK UNDER THIS CONTRACT SHALL BE PERFORMED BY COM-
<br />PETENT WORKMEN AND EXECUTED IN A NEAT AND WORKMANLIKE
<br />MANNER WORK SHALL BE PROPERLY PROTECTED DURING CON-
<br />STRUCTION AND COMPLETION, INSTALLATION SHALL BE THOROUGHLY
<br />CLEANED OF ALL DEBRIS PRESENT AS A RESULT OF THIS CONTRACT
<br />AND SHALL BE REMOVED FROM THE PREMISES, DO NOT ABANDON.
<br />CODES AND REGULATIONS
<br />EACH SUBCONTRACTOR SHALL COMPLY WITH ALL LAWS, ORDINANCES,
<br />RULES AND REGULATIONS BEARING ON THE CONDUCT OF THE WORK AS
<br />DRAWN AND SPECIFIED. IF A SUBCONTRACTOR OBSERVES THAT THE
<br />DRAWINGS AND SPECIFICATIONS ARE At A VARIANCE, HE SHALL PROMPTLY
<br />NOTIFY THE GENERAL CONTRACTOR AND THE TENANT IN WRITING. IF
<br />ANY SUBCOMTRACTOR PERFORMS ANY WORK KNOWING IT TO BE CONTRARY
<br />TO LAWS, ORDINANCES, RULES AND REGULATIONS AND WITHOUT GIVING
<br />SUCH NOTICE, THE SUBCONTRACTOR SHALL BEAR ALL COSTS ARISING
<br />THEREFROM.
<br />PROTECTION OF WORK AND PROPERTY
<br />A. EACH SUBCONTRACTOR SHALL CONTINUOUSLY MAINTAIN ADEQUATE
<br />PROTECTION OF ALL HIS WORK FROM DAMAGE AND SHALL PROTECT
<br />THE OWNER'S PROPERTY FROM INJURY OR LOSS ARISING FROM HIS
<br />WORK ANY SUCH DAMAGE, INJURY, OR LOSS, EXCEPT SUCH AS
<br />MAY BE DIRECTLY DUE TO CAUSES BEYOND HIS CONTROL AND NOT
<br />TO HIS FAULT OR NEGLIGENCE, SHALL BE THE RESPONSIBILITY OF
<br />THE SUBCONTRACTOR HE SHALL ADEQUATELY PROTECT ADJACENT
<br />PROPERTY AS WELL.
<br />B. EACH SUBCONTRACTOR SHALL TAKE ALL NECESSARY PRECAUTIONS
<br />FOR THE SAFETY OF THEIR EMPLOYEES ON THE WORK AND SHALL
<br />COMPLY WITH ALL PROVISIONS OF FEDERAL, STATE AND LOCAL
<br />BUILDING CODES AND SAFETY LAWS TO PREVENT ACCIDENTS OR
<br />INJURY TO PERSONS ON OR ADJACENT TO THE PREMISES WHERE
<br />THE WORK IS BEING PERFORMED. EACH SUBCONTRACTOR SHALL
<br />MAINTAIN ALL INSURANCE REQUIRED TO PROTECT HIMSELF, THE
<br />OWNER AND TENANT FOR THE DURATION OF THE WORK AGAINST
<br />PROPERTY DAMAGE AND PUBLIC LIABILITY.
<br />CHANGES IN THE WORK
<br />THE TENANT, WITHOUT INVALIDATING THE CONTRACT, MAY ORDER EXTRA
<br />WORK OR MAKE CHANGES BY ALTERING, ADDING TO, OR DEDUCTING
<br />FROM THE WORK, WITH CONTRACT SUM BEING ADJUSTED ACCORDINGLY.
<br />COOPERATION
<br />ALL WORK UNDER THESE SPECIFICATIONS SHALL BE ACCOMPLISHED IN
<br />CONJUNCTION WITH OTHER CONTRACTORS AND TRADES OF THIS PROJECT
<br />IN A MANNER WHICH WILL ALLOW EACH CONTRACTOR AND TRADE SUF-
<br />FICIENT TIME AT THE PROPER STAGE OF CONSTRICTION TO FULFILL HIS
<br />CONTRACTS. CONTRACTORS SHALL CONTACT OWNER FOR INSTRUCTIONS
<br />SHOULD ANY QUESTIONS ARISE BETWEEN TRADES AS TO THE INSTALL-
<br />ATION OF LINES, DUCTS, CONDUITS, FIXTURES, OR EQUIPMENT, OR
<br />SHOULD It APPEAR DESIRABLE TO ANY GENERAL CONSTRICTION WHICH
<br />WOULD AFFECT THE APPEARANCE OR STRENGTH OF THE STRUCTURE.
<br />SUBSTITUTION OF MATERIALS
<br />MANUFACTURERS ARE LISTED ON PLANS TO ESTABLISH A STANDARD.
<br />THE PRODUCTS OF OTHER MANUFACTURERS WILL BE ACCEPTABLE, IF IN
<br />THE OPINION OF THE TENANT, THE SUBSTITUTE MATERIAL IS OF QUALITY
<br />EQUAL TO OR BETTER THAN THE MATERIAL SPECIFIED, AMC) WILL SERVE
<br />WITH EQUAL EFFICIENCY AND DEPENDABILITY, FOR THE PURPOSE OF
<br />WHICH THE ITEMS SPECIFIED WERE INTENDED.
<br />SHOP DRAWINGS
<br />SHOP DRAWINGS AMC) CATALOG DATA ON ALL MAJOR ITEMS OF EQUIPMENT
<br />AND SYSTEMS, AND OTHER SUCH ILLUSTRATIVE MATERIAL THAT MAY BE
<br />CONSIDERED NECESSARY BY THE TENANT, SHALL BE SUBMITTED BY THIS
<br />CONTRACTOR IN ADEQUATE TIME TO PREVENT DELAY AND/OR CON-
<br />STRUCTION MODIFICATIONS.
<br />DRAWINGS AND SPECIFICATIONS
<br />A. THE DRAWINGS DIAGRAMMATICALLY INDICATE THE LOCATIONS OF THE
<br />VARIOUS LINES, DUCTS, CONDUITS, FIXTURES, AND EQUIPMENT AND
<br />THE METHOD OF CONNECTING AMC) CONTROLLING THEM. It IS NOT
<br />INTENDED TO SHOW EVERY CONNECTION IN DETAIL AND ALL FITTINGS
<br />REQUIRED FOR A COMPLETE SYSTEM.
<br />B. SHOULD ANY CHANGES BE DEEMED NECESSARY BY THE CONTRACTOR,
<br />TO ANY ITEMS SHOWN ON CONTRACT DRAWINGS, SHOP DRAWINGS,
<br />DESCRIPTIONS, AND THE REASON FOR THE PROPOSED CHANGES
<br />SHALL BE SUBMITTED TO THE OWNER FOR APPROVAL.
<br />RESPONSIBILITY
<br />A. THE CONTRACTOR WILL BE HELD RESPONSIBLE FOR THE SATISFACTORY
<br />AND COMPLETE EXECUTION OF ALL WORK INCLUDED IN HIS CONTRACT.
<br />HE SHALL PRODUCE COMPLETE AMC) FULLY OPERATIONAL SYSTEMS AMC)
<br />PROVIDE ALL INCIDENTAL ITEMS REQUIRED AS PART OF HIS WORK,
<br />REGARDLESS OF WHETHER SUCH ITEM IS PARTICULARLY SPECIFIED OR
<br />INDICATED. FOR EXAMPLE, ON SINK INSTALLATIONS, ESCUTCHEONS SHALL
<br />BE PROVIDED FOR COUNTERTOP PENETRATIONS, ALTHOUGH THEY WERE
<br />NOT SPECIFICALLY IDENTIFIED IN THE CONTRACT DOCUMENTS.
<br />B. CONTRACTOR SHALL SUPPLY TO LANDLORD AND TENANT A CERTIFIED
<br />AIR BALANCE REPORT AT COMPLETION OF PROJECT. THIS SHALL BE
<br />REQUIRED FOR BOTH REMODELED AND NEW STORES.
<br />HEATING, VENTILATING AMC) AIR CONDITIONING
<br />GENERAL
<br />A. THE WORK COVERED BY THIS SECTION OF THESE SPECIFICATIONS
<br />SHALL BE ACCOMPLISHED IN ACCORDANCE WITH THE RESPECTIVE
<br />DRAWINGS, INFORMATION OR INSTRUCTIONS TO BIDDERS, GENERAL
<br />CONDITIONS, ADDENDA, OR DIRECTIVES WHICH MAY BE ISSUED BY
<br />THE OWNER, SHALL BE COMPLIED WITH IN EVERY ASPECT.
<br />B. THE LISTING HEREIN OF AN ARTICLE OR MATERIAL, OPERATION OR
<br />METHOD, REQUIRES THAT THE CONTRACTOR SHALL FURNISH AND
<br />INSTALL EACH ITEM LISTED, UNLESS SPECIFICALLY NOTED TO THE
<br />CONTRARY. THE CONTRACTOR SHALL PERFORM EACH OPERATION
<br />PRESCRIBED OR LISTED ACCORDING TO THE CONDITIONS STATED.
<br />EXAMINATION OF SITE
<br />ALL CONTRACTORS SUBMITTING PROPOSALS FOR THIS WORK SHALL FIRST
<br />EXAMINE THE SITE AND ALL EXISTING CONDITIONS AFFECTING HIS WORK
<br />ALL PROPOSALS SHALL SPECIFY, IN WRITING, ALL SUCH CONDITIONS
<br />THAT MAY ALTER OR AFFECT THE WORK UNDER THIS CONTRACT.
<br />SCOPE
<br />FURNISH ALL MATERIALS, EQUIPMENT, AND LABOR NECESSARY FOR A
<br />COMPLETE AND FULLY OPERATIONAL HEATING, VENTILATING, AND AIR
<br />CONDITIONING SYSTEM EXCEPT AS SPECIFICALLY EXCLUDED BY DRAWINGS
<br />AND/OR BY TENANT'S DIRECTIONS.
<br />EQUIPMENT
<br />A. I. EXISTING TO REMAIN.
<br />B. FILTERS - FILTERS SHALL BE OF THE THROW AWAY TYPE WHEREVER
<br />POSSIBLE. IF FILTERS ARE BY NECESSITY THE PERMANENT TYPE,
<br />THEY MUST BE OF THE CLEANABLE, HIGH VELOCITY TYPE AND
<br />SHALL BE AMERICAN AIR FILTERS, AIR MAYS, EVANS, OR
<br />APPROVED EQUAL. FILTERS SHALL BE OF THE OPTIMUM THICKNESS
<br />AND DESIGN FACE VELOCITY SHALL NOT EXCEED 500 FPM.
<br />INSTALLATION OF THE AIR CONDITIONING UNIT SHALL NOT IMPEDE
<br />OR CONFLICT WITH ACCESS TO FILTERS. IF THE FILTERS ARE IN
<br />FRAME HOLDERS, HOLDERS SHALL BE PROVIDED WITH A LEFT
<br />HANDLE.
<br />C. EXHAUST FANS
<br />1. AS INDICATED ON SHEET Mi.
<br />D. ALL AIR HANDLING UNITS SHALL BE EQUIPPED WITH PROGRAMABLE
<br />THERMOSTAT CAPABLE OF BEING ADJUSTED TO 551F
<br />HEATING AMC) 857E COOLING. DESIGN AND STANDARD CONDITIONS
<br />FOR THERMOSTAT OPERATION SHALL BE AS FOLLOWS:
<br />COOLING: 157F MAXIMUM OCCUPIED COOLING TEMPERATURE
<br />857F COOLING NIGHT SETBACK -
<br />HEATING: 107F MAXIMUM OCCUPIED HEATING TEMPERATURE
<br />607F HEATING NIGHT SETBACK
<br />FAN: CONTINUOUS IN OCCUPIED AND RECOVERY MODE AND WITH
<br />HEATING OR COOLING EQUIPMENT IN UNOCCUPIED MODE.
<br />DEADBAND: CAPABLE OF MAINTAINING A 57F DEADBAND.
<br />CLOCK: i DAY CAPABLE OF -1 DIFFERENT DAY SCHEDULES.
<br />OVERNIGHT: HAVE A 2 HOUR OVERRIDE ACCESSIBLE TO MANAGER
<br />BACKUP: CAPABLE OF MAINTAINING PROGRAMMED SETTING FOR AT
<br />LEAST 10 HOURS WITHOUT POWER
<br />BEAM
<br />BEAM
<br />X
<br />N
<br />CLEVIS HANGER
<br />OVERSIZED FOR
<br />INSULATION
<br />WITH 18' ROLLED
<br />SLEEVE FOR
<br />SUPPORT IS07 -
<br />all PIPEANCzER DETAIL
<br />SCALE:
<br />HANGER SPACING AND ROD SIZE
<br />PIPE
<br />MAX
<br />ROD
<br />SIZE
<br />SPAN
<br />SIZE
<br />1/2'
<br />-1'
<br />3/8,
<br />3/4'
<br />i'
<br />3/5,
<br />1'
<br />l'
<br />3/8,
<br />11/4'
<br />i'
<br />3/8,
<br />11/2"
<br />9'
<br />3/5,
<br />2'
<br />10'
<br />3/8,
<br />2 1/2'
<br />11'
<br />1/2'
<br />3
<br />12'
<br />1/2'
<br />31/2'
<br />13'
<br />1/2'
<br />4'
<br />14'
<br />5/8'
<br />5'
<br />16'
<br />5/5,
<br />6'
<br />17'
<br />3/4'
<br />8'
<br />19'
<br />3/4'
<br />10,
<br />22'
<br />1/5"
<br />12'
<br />23'
<br />I/8"
<br />14'
<br />25'
<br />1'
<br />16'
<br />21'
<br />1'
<br />18'
<br />28'
<br />1'
<br />20'
<br />30'
<br />11/4,
<br />24
<br />32'
<br />11/4"
<br />4k (It ssuihrr
<br />DUCTWORK
<br />J
<br />`��. •�......,�.��y,�,
<br />A. SQUARE/RECTANGULAR DUCTWORK SHALL BE CONSTRUCTED OF NEII
<br />_
<br />F
<br />N
<br />lz
<br />0.6'
<br />�,
<br />GALVANIZED PRIME GRADE SHEET STEEL OF THE FOLLOWING GAUGES 0'
<br />N
<br />Z
<br />ra . N o
<br />DUCT SIZE GAUGEo
<br />N
<br />O
<br />=? w r:J.
<br />12' AND LESS NO. 2fo U.S. GAUGE
<br />`~
<br />s >
<br />.✓` o r o-
<br />13' TO 30' NO. 24 U.S. GAUGE
<br />Q
<br />b - �,
<br />31' TO 54' NO. 22 U S. GAUGE "
<br />N
<br />W
<br />U-i
<br />• .
<br />i ........
<br />55' TO 84' NO. 20 U.S. GAUGE
<br />E
<br />,,r� Q�;. •
<br />86' AND OVER NO. 18 U.S. GAUGE
<br />r'r'r"`•
<br />ALL EXHAUST AMC) RELIEF AIR DUCTS SHALL BE GALVANIZED STEEL.
<br />B. SQUARE AND RECTANGULAR DUCTWORK SHALL BE CONSTRUCTED AS
<br />FOLLOWS:
<br />SIZE METHOD
<br />11' AND LESS 'S' AND DRIVE CLEATS
<br />18' TO 30' 'L' STANDING SEAMS ON
<br />V -0' CENTERS
<br />31' TO 54' 1-1/4' STAND ING SEAMS
<br />ON V-0' CENTERS
<br />ROUND DUCTWORK SHALL BE CONSTRUCTED OF NEW GALVANIZED
<br />PRIME GRADE SHEET STEEL OF THE FOLLOWING GAUGES:
<br />DUCT SIZE (DIAMETER) DUCTS FITTINGS
<br />8' AND LESS 24 22
<br />V TO 18" 22 20
<br />IV TO 30' 20 18
<br />ALL SO DEGREE ELBOWS FOR ROUND DUCTWORK SHALL BE FIVE (5)
<br />PIECE. ALL LONGITUDINAL SEAMS SHALL BE FORMED BY PITTSBURGH
<br />LOCKS. JOINTS SHALL BE SWAGGED WITH ONE-HALF INCH (1/2')
<br />OVERLAP.
<br />C. ALL SUPPLY AIR DUCTS (HEATING AND COOLING), RETURN AIR
<br />DUCTS AND OUTSIDE AIR DUCTS SHALL BE GALVANIZED STEEL WITH
<br />MINIMUM 2' (INSTALLED R-5 MIN.) THICK EXTERNAL INSULATION
<br />WITH VAPOR BARRIER
<br />D. CONTRACTOR SHALL SUPPLY AMC) INSTALL INSECT SCREENS ON ALL
<br />DUCT OPENINGS WHICH TERMINATE OUTDOORS. INSECT SCREENS
<br />SHALL BE 10 GAUGE, ONE -HALF INCH (1/2') MESH IN REMOVABLE
<br />GALVANIZED STEEL FRAMES.
<br />E. ALL DUCTWORK SHALL BE DESIGNED IN ACCORDANCE WITH THE
<br />PROCEDURES DESCRIBED IN THE LATEST EDITION OF THE AMERICAN
<br />SOCIETY OF HEATING REFRIGERATION AMC) AIR CONDITIONING ENGINEERS
<br />GUIDE (ASHRAE), FABRICATED AMC) INSTALLED IN ACCORDANCE WITH
<br />THE METHODS RECOMMENDED IN THE SHEET METAL AMC) AIR CON-
<br />DITIONING CONTRACTORS NATIONAL ASSOCIATION (SMACNA) LOW
<br />VELOCITY DUCT MANUAL, LATEST EDITION.
<br />I. ALL JOINTS, LONGITUDINAL AMC) TRANSVERSE SEAMS, AND
<br />CONNECTIONS IN DUCTWORK MUST BE SECURELY SEALED USING
<br />WELDMENTS± MECHANICAL FASTENERS WITH SEALS, GASKETS, OR
<br />MASTICS± MESH AND MASTIC SEALING SYSTEMS± OR TAPES. TAPES AND
<br />MASTICS MUST BE LISTED AND LABELED IN ACCORDANCE WITH UL
<br />181A OR UL 1815. ALL LONGITUDINAL AND TRANSVERSE JOINTS,
<br />SEAMS AND CONNECTIONS OF SUPPLY AND RETURN DUCTS OPERATING
<br />AT STATIC PRESSURES LESS THAN OR EQUAL TO 2' W.G. SHALL BE
<br />SECURELY FASTENED AND SEALED WITH WELDS GASKETS, MASTICS
<br />(ADHESIVES), MASTIC -PLUS -EMBEDDED FABRIC SYSTEMS OR TAPES
<br />INSTALLED IN ACCORDANCE WITH MANUFACTURER'S INSTALLATION
<br />INSTRUCTIONS.
<br />2. MECHANICAL FASTENERS AMC) SEALS, MASTICS, OR GASKETS MUST
<br />BE USED WHEN CONNECTING DUCTS TO FANS AND OTHER AIR
<br />DISTRIBUTION EQUIPMENT.
<br />F. FLEXIBLE AIR DUCT FOR CONNECTIONS BETWEEN S.M. DUCT AND
<br />DIFFUSER SHALL BE AIR DUCT LISTED BY UNDERWRITERS LABORATORIES
<br />UNDER UL STANDARD 181 AS A GLASS 1 FLEXIBLE AIR DUCT AND
<br />COMPLYING WITH NFPA STANDARDS SOA AND S08. DUCT SHALL BE
<br />FACTORY MADE AND COMPOSED OF A CPE LINER DUCT PERMANENTLY
<br />BOUNDED TO A COATED SPRING STEEL WIRE HELIX AND SUPPORTING A
<br />FIBER GLASS INSULATING BLANKET. R.-5.0 LOW PERMEABILITY OUTER
<br />VAPOR BARRIER OF FIBER GLASS REINFORCED FILM LAMINATE SHALL
<br />COMPLETE THE COMPOSITE.
<br />HANGERS AND SUPPORTS
<br />A. ALL HORIZONTAL DUCTS HAVING A DIMENSION OF 40 INCHES AND
<br />LESS SHALL BE SUPPORTED BY MEANS OF BAND IRON HANGERS
<br />OF NO. 18 U.S. GAUGE ATTACHED TO DUCT BY MEANS OF RIVETS,
<br />SCREWS OR CLAMPS, AMC) FASTENED TO STRUCTURE ABOVE BY
<br />TOGGLE BOLTS OR OTHER MEANS. EACH SECTION OF DUCTWORK
<br />SHALL HAVE AT LEAST ONE PAIR OF SUPPORTS. VERTICAL DUCTS
<br />SHALL BE SUPPORTED WITH 1-1/4' x 1-1/4' x 1-1/4' ANGLES
<br />AT FLOOR PENETRATIONS.
<br />B. ALL HORIZONTAL DUCTS HAVING A DIMENSION OF 40 INCHES AND
<br />MORE SHALL BE SUPPORTED BY MEANS OF ANGLE IRON TRAPEZE
<br />HANGERS. EACH SECTION OF DUCTWORK SHALL HAVE AT LEAST
<br />ONE PAIR OF SUPPORTS.
<br />FLASHING
<br />A. CONTRACTOR SHALL PROVIDE WATER TIGHT 24 GA. SHEET METAL
<br />FLASHINGS AT ALL EXTERIOR WALLS AND ROOF PENETRATIONS.
<br />B. ALL CUTTING OF ROOF OPENINGS, SUPPORTS FOR ROOF OPENINGS,
<br />PITCH PANS, ROOF CURBS, FLASHINGS, COUNTER FLASHINGS, REPAIR
<br />TO ROOF, ETC. ASSOCIATED WITH HVAC SUBCONTRACTOR SHALL BE
<br />INCLUDED IN THE RESPONSIBILITY OF THE HVAC SUBCONTRACTOR.
<br />HE SHALL EMPLOY THE LANDLORD'S ROOFERS FOR THIS WORK TO
<br />MAINTAIN THE ROOF WARRANTY.
<br />DAMPERS
<br />A. SPLITTER DAMPERS SHALL BE FABRICATED OF SHEET STEEL NOT
<br />LESS THAN NO. 16 U.S. GAUGE WITH THE LEADING EDGE HEMMED.
<br />EACH DAMPER TO BE SIZED ADEQUATELY TO COVER THE SMALLER
<br />OF THE TWO OPENINGS IT CONTROLS. DAMPERS SHALL BE
<br />CONTROLLED AS FOLLOWS:
<br />EXPOSED OR ACCESSIBLE DUCTWORK - LOCKING QUADRANTS EQUAL
<br />TO YOUNG REGULATOR NO. 1 WITH DAMPER ROD END BEARINGS ON
<br />OPPOSITE END.
<br />CONCEALED DUCTWORK - LOCKING QUADRANT EQUAL TO YOUNG
<br />REGULATOR NO. 315 (CHROMIUM PLATED WITH DAMPER ROD END
<br />BEARINGS ON BOTH ENDS).
<br />B. VOLUME DAMPERS SHALL BE OF THE OPPOSED INTERLOCKING TYPE
<br />AS MANUFACTURED BY AMERICAN FOUNDRY AND FURNACES CO.
<br />(AFFCO) OR EQUAL. BLADES SHALL BE OF NO. Ifo GAUGE SHEET
<br />METAL AND SHALL NOT EXCEED 48' IN LENGTH OR 12' IN WIDTH.
<br />BLADES SHALL BE ON ONE-HALF INCH (1/29 DIAMETER RUSTPROOF
<br />AXLE. BEARINGS TO BE OF THE SELF-LUBRICATING FERRULE TYPE.
<br />C. FIRE DAMPERS SHALL BE SUPPLIED AND INSTALLED BY HVAC CON-
<br />TRACTOR AT DUCT PENETRATIONS IN FIRE RATED WALLS, FLOORS,
<br />CEILINGS AND ROOF AS REQUIRED. COORDINATE WITH LANDLORD,
<br />LOCAL FIRE MARSHALL AND ALL CODES AND GOVERNING AUTHORITES
<br />HAVING JURISDICTION.
<br />D. FIELD FABRICATED TURNING VANES SHALL BE ACCEPTABLE IN
<br />SQUARE ELBOWS. PROVIDE AND INSTALL BARBER-COLMAN AIRTURNS
<br />OR EQUAL. TURNING VANES SHALL BE OF THE SAME GAUGE METAL
<br />AS THE DUCT IN WHICH THEY ARE INSTALLED. RADIUS ELBOWS
<br />SHALL HAVE A CENTER LINE RADIUS OF ONE AND ONE-HALF (1-1/2)
<br />TIMES THE DUCT WIDTH.
<br />DUCTWORK - EXCEPTIONS
<br />DUCTWORK FOR EXHAUST OR OUTSIDE SUPPLY AIR SHALL BE ALL
<br />METAL AND CONSTRICTED ACCORDING TO RECOMMENDED PRACTICES
<br />OF THE LATEST ISSUE OF ASHRAE.
<br />SUPPORT OF DUCT SYSTEM
<br />HANGER DESIGN SHALL BE AS DESCRIBED IN THE LATEST EDITION OF
<br />THE "SMACNA' MANUAL. RE INFORCEMENT MEMBERS MAY BE USED TO
<br />SUPPORT DUCT SYSTEM PROVIDED DETAILS OUTLINED IN THE 'SMACNA'
<br />MANUAL ARE ADHERED TO.
<br />DUCTS SHALL BE SUPPORTED AT ALL TURNS AND TRANSITIONS AND NOT
<br />MORE THAN 8'-0' O.G. STRAIGHT DUCTS UP TO 59" MAX. DIMENSIONS
<br />SHALL BE SUPPORTED 6'-O' O.G. DUCTS OVER 60' MAX. DIMENSIONS
<br />SHALL BE SUPPORTED At 4'-O' O.G.
<br />REINFORCEMENT
<br />ALL DUCTS SHALL BE REINFORCED ACCORDING TO THE LATEST EDITION
<br />OF SMACNA MANUAL. MATERIALS FOR REINFORCEMENT MEMBERS SHALL
<br />BE GALVANIZED STEEL. ALL SCREWS AND WASHERS SHALL BE PLATED
<br />OR GALVANIZED.
<br />TESTING AND ADJUSTING
<br />CONTRACTOR SHALL DEMONSTRATE OPERATION OF SYSTEM TO FULL
<br />SATISFACTION OF TENANT, SHALL BALANCE AIR FLOW IN ACCORDANCE
<br />WITH AIR QUANTITIES ON DRAWINGS AND SHALL RECORD VOLUME
<br />READINGS IN ACCORDANCE WITH ASHRAE AND PROVIDE SAME TO TENANT.
<br />OPERATION AND MAINTENANCE DOCUMENTATION MUST BE PROVIDED TO
<br />THE OWNER THAT INCLUDES AT LEAST THE FOLLOWING INFORMATION:
<br />A. EQUIPMENT CAPACITY (INPUT AND OUTPUT) AND REQUIRED
<br />MAINTENANCE ACTIONS.
<br />B. EQUIPMENT OPERATION AND MAINTENANCE MANUALS.
<br />C. HVAC SYSTEM CONTROL MAINTENANCE AND CALIBRATION
<br />INFORMATION, INCLUDING WIRING DIAGRAMS, SCHEMATICS, AND
<br />CONTROL SEQUENCE DESCRIPTIONS± DESIRED OR FIELD -DETERMINED
<br />SET POINTS MUST BE PERMANENTLY RECORDED ON CONTROL
<br />DRAWINGS, AT CONTROL DEVICES, OR, FOR DIGITAL CONTROL
<br />SYSTEMS, IN PROGRAMMING COMMENTS.
<br />OPERATE.
<br />D. COMPLETE NARRATIVE OF HOW EACH SYSTEM IS INTENDED TO
<br />ALL PIPING SHALL WITHSTAND AIR PRESSURE TESTING PER
<br />GOVERNING PLUMBING CODE.
<br />GUARANTEE
<br />ALL MATERIALS, EQUIPMENT, AND WORKMANSHIP SHALL BE GUARANTEED
<br />FOR A PERIOD OF ONE (1) YEAR AFTER DATE OF ACCEPTANCE. THE
<br />COMPLETED SYSTEM SHALL BE FULLY OPERATIIONAL AND ACCEPTANCE
<br />BY TENANT SHALL BE A CONDITION OF THIS CONTRACT. ALL WORK
<br />FOUND TO BE DEFECTIVE SHALL BE REPAIRED OR REPLACED BY THIS
<br />SUBCONTRACTOR WITHOUT ADDITIONAL COST TO THE TENANT.
<br />ACCESSORY ITEMS
<br />ALL MANUAL DAMPERS, FIRE DAMPERS, TURNING VANES, REGISTER CON-
<br />NECTIONS, ACCESS DOORS OR OTHER ASSOCIATED ACCESSORIES SHALL
<br />BE INSTALLED ACCORDING TO THE LATEST EDITION OF 'SMACNA' MANUAL.
<br />SPRINKLER SYSTEM
<br />A. SHOP DRAWINGS -THE SPRINKLER CONTRACTOR SHALL SUBMIT SHOP
<br />DRAWINGS TO THE TENANT'S LANDLORD AND TO THE APPROPRIATE
<br />AUTHORITIES AND INSURANCE UNDERWRITER FOR THEIR APPROVAL.
<br />A COPY OF THE APPROVAL LETTER FROM THESE AUTHORITIES SHALL
<br />BE FORWARDED TO THE TENANT, LANDLORD AND DESIGN ARCHITECT.
<br />B. SPRINKLER HEAD TYPES SHALL BE AS FOLLOWS:
<br />1. SHOW WINDOWS:
<br />HIGH TEMPERATURE, FULLY RECESSED, PAINT TO MATCH CEILING
<br />2. AREAS WITH CEILINGS:
<br />FULLY RECESSED, PAINT TO MATCH CEILING
<br />3. PUBLIC AREAS WITH OPEN TO DECK CEILINGS:
<br />CHROME, UPRIGHT
<br />4. STOCK AREAS OPEN TO DECK:
<br />BRASS, UPRIGHT
<br />NOTE FOR GENERAL CONTRACTOR:
<br />IT IS THE RESPONSIBILITY OF THE TENANT'S GENERAL CONTRACTOR TO
<br />MAKE USE OF APPLICABLE NOTES AND SPECIFICATIONS LISTED ON THIS
<br />SHEET AS THEY MAY PERTAIN TO THE SPECIFIC JOB.
<br />0
<br />kid 0
<br />75 +>
<br />d 4-'
<br />O 0)
<br /><n
<br />Q� S
<br />+' U
<br />d d
<br />:5 In
<br />IELn
<br />S d
<br />U
<br />O
<br />U E
<br />d
<br />o S
<br />D)
<br />• d
<br />d
<br />L
<br />LL-
<br />V)
<br />U)
<br />N
<br />N
<br />V)
<br />W d
<br />c
<br />O
<br />D
<br />U
<br />0
<br />LC)
<br />41
<br />i
<br />0 O
<br />OX
<br />�•U:2L�
<br />c
<br />CN "
<br />C O
<br />cf)
<br />-s-- Ln
<br />(D
<br />U) t)
<br />Lu
<br />Z
<br />Lu
<br />!u
<br />V
<br />z
<br />O
<br />=
<br />Q C)
<br />t�
<br />w �
<br />—) O
<br />w
<br />=) J
<br />O `L
<br />m �
<br />J_ J
<br />Z
<br />¢ _
<br />0
<br />O
<br />CN
<br />CN
<br />H-
<br />I� N
<br />w
<br />a
<br />z
<br />z
<br />0
<br />F
<br />EL
<br />w
<br />U
<br />w
<br />0
<br />I
<br />k
<br />a
<br />0
<br />w
<br />rn
<br />0
<br />or..-
<br />I
<br />o
<br />�
<br />z
<br />O
<br />N
<br />U
<br />:0
<br />� LAJ
<br />LLj
<br />C:)
<br />d
<br />�12
<br />
|