|
-
<br />CLEAR ANODIZED
<br />ALUM. FRAME WITH
<br />INSULATED GLAZING
<br />4
<br />C) C)SECTIONAL OVERN
<br />I
<br />� a
<br />z
<br />ti
<br />PADLOCKING TRACK LATCH
<br />TYPE A AT BOTH TRACKS
<br />TYPE D
<br />180' DOOR VIEWER @ +60" AFF
<br />1-3/4", PAINTED, FLUSH HOLLOW I
<br />PRE FINISI-IED
<br />MARATHON PACKAGF
<br />CHUTE SECURITY DOOR
<br />SLIDE BOLT WITH LATCH \
<br />AND CHAIN FOR G,C,
<br />SUPPLIED BEST PADLOCK
<br />I
<br />FINISH FLR.
<br />TYPE K
<br />ri__�DOOR YE13
<br />�,A_!LO SCALE: N.T.S.
<br />IYPE E
<br />TYPE H
<br />IAICH Al
<br />BOTH SIDES
<br />CENTERED 180'
<br />VIEWER AT 5'-0"
<br />A.F.F.
<br />DOOR TYPE NOTES
<br />THE FOLLOWING ARE THE ROSS MINIMUM ACCESSIBILITY REQUIREMENIS FOR OPERABLE INTERIOR
<br />/ EXTERIOR DOORS AT ROSS STORES REGARDLESS OF LESSER OR ABSENI REQUIREMENTS OF
<br />GOVERNMENTAL AUTHORITY. MERE SHALL BE NO CASTS WHERE THE OPERABLE DOORS AT ROSS
<br />STORES DO NOI MEET THE FOLLOWING MINIMUM REQUIREMENTS. LANDLORD MUST ENSURE THAT
<br />IF HIGHER OR MORE STRINGENT STANDARDS ARE REQUIRED BY GOVERNMENTAL AUTHORITY THAT
<br />THOSE HIGHER STANDARDS ARE MET.
<br />1. DOORS MUST BE A MINIMUM OF 3'-0" WIDE AND 6'-8" HIGH.
<br />2, DOORS MUST OPEN A MINIMUM OF 90 DEGREES.
<br />3. CLEAR WIDTH OF DOORWAYS MUST BE 32" MINIMUM,
<br />4. DOUBLE DOORS / AUTOMATIC DOORS AT IFAST ONE LEAF MUST COMPLY WITH ITEMS 1
<br />THROUGH 3 ABOVE,
<br />5. THE BOTTOM 10" OF Al,I DOORS, EXCEPT AUTOMATIC AND SLIDING DOORS, SHALL HAVE A
<br />SMOOTH, UNINTERRUPTED SURFACE TO ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR
<br />FOOTREST WITHOIJI CRFAHNG A TRAP OR HAZARDOUS CONDITION. WHERE NARROW FRAME DOORS
<br />ARE USED, A 10" HIGH SMOOTH PANEL SHALL BE INSIAI I_I I) ON TIIE PUSH SIDE OF THE DOOR,
<br />WHICH ALLOWS THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST WITHOUT A TRAP OR
<br />HAZARDOUS CONDITION,
<br />6. M S MAXIMUM EFFORT TO OPERATE DOOR SHALL NOT EXCEED 5 LBS, FOR EXTERIOR AND
<br />INTERIOR DOOR, SUCH PULL OR PUSH EFFORT BEING APPLIED AT RIGHT ANGLES TO HINGED
<br />DOORS AND AT THE CENTER PLANE OF SLIDING OR FOLDING DOORS. COMPENSAIING DEVICES OR
<br />AUIOMATIC DOOR OPERATORS MAY BE UTILIZED TO MEET THE ABOVE STANDARDS. WHEN FIRE
<br />DOORS ARE REQUIRED THE MAXIMUM EFFORI 10 OPERATE THE DOOR MAY BE INCREASED TO
<br />THE MINIMUM ALLOWABLE BY THE APPROPRIATE ADMINISTRATIVE AUTHORITY, BUI SHALT- NOT
<br />EXCEED 15 1,13S.
<br />/. IF IHE DOOR HAS A CLOSER, THEN THE SWEEP PERIOD OF THE CLOSER SHALL BE
<br />ADJUSTED SO THAT FROM AN OPEN POSITION OF /0 DEGREES, THE DOOR Will- TAKE AT LEAST
<br />3 SECONDS TO MOVE TO A POINT 3" FROM THE LATCH, MEASURED TO THE LANDING EDGE OF
<br />DOOR,
<br />8. HAND ACTIVATED DOOR OPENING HARDWARE SHALL BE CENTERED BETWEEN 30" AND 44"
<br />ABOVE THE FLOOR. LATCHING AND LOCKING DOORS THAT ARE HAND ACTIVATED AND WHICH ARE
<br />IN A PATH OF TRAVEL SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER TYPE HARDWARE,
<br />PANIC B AS, PUSI-I-PULL ACTIVATING BARS OR OTHER HARDWARE DESIGNED TO PROVIDE
<br />PASSAGE WITHOUT REQUIRING THE ABILITY 10 GRASP THE OPENING HARDWARE,
<br />9. WHERE THE PLANE OF THE DOORWAY IS OFFSET 8 OR MORE INCHES FROM ANY
<br />OBSTRUCTION WITHIN 18" MEASURED LATERAI I Y ON IHE LATCH SIDE, THE DOOR SHALL BE
<br />PROVIDED WITH MANEUVERING CLEARANCE FOR FRONT APPROACH.
<br />10,
<br />. FLOOR OR LANDING ON EACH SIDE OF THE DOOR TO BE LEVEL AND CLEAR. l FVl I ARE
<br />A
<br />IN THE DIRECTION OF THE DOOR SWING IS A MINIMUM OF 60" IN LENGTH, LEVEL AREA
<br />OPPOSITE THE DIRECTION OF THE DOOR SWING IS A MINIMUM OF 44-48" IN LENGTH,
<br />DEPENDENT UPON DIRECTION OF THE APPROACH & EXISTENCE OF A LATCH & CLOSER. SURFACE
<br />SLOPE OF THE LEVEL AREA SHALL NOT EXCEED 1:50 GRADIENT (2%).
<br />11. TIFF WIDTH OF THE LEVEL AREA ON THE SIDE TO WHICH THE DOOR SWINGS SHALL
<br />EXTFND 24" PAST THE STRIKE EDGE OF THE DOOR FOR EXTERIOR DOORS & 18" PAST THE
<br />STRIKE EDGE FOR INTERIOR DOORS.
<br />DOOR SCHEDULE -
<br />DOOR NUMBER
<br />TYPE
<br />W
<br />H
<br />D
<br />IIARDWARE TYPE (SEE NOTE 7L)
<br />1 STOREFRONT
<br />A
<br />11'-0"
<br />7'-0"
<br />-
<br />KEYED LOCKSET
<br />SLIDING DOOR
<br />C°J VESTIBULE
<br />J
<br />8' 6"
<br />7'-0"
<br />-
<br />NO LOCKSET
<br />°J SLIDING DOOR
<br />DFI AYED EXIT DEVICE
<br />C) EXIT
<br />D
<br />3'-0"
<br />7'-0"
<br />1 3/4"
<br />(SEE NOIL 15)
<br />EXTERIOR OPERABLE HARDWARE
<br />� PROCESSING ROOM
<br />IT
<br />3'-0"
<br />7'-0"
<br />1 3/4"
<br />PANIC DEVICE
<br />(SEE NOTE 20)
<br />�.`'./ MAN DOOR
<br />NO EXTERIOR OPERABLE HARDWARE
<br />DELAYED EXIT DEVICE
<br />EXIT
<br />D
<br />3'-0"
<br />7' 0"
<br />1 3/4"
<br />(SEE NOTE 15)
<br />NO EXTERIOR OPERABIC HARDWARE
<br />17 TRASII COMPACTOR
<br />K
<br />S-4"
<br />S-4"
<br />-
<br />CASE OPENING, SLIDEB01_T, BEST PADLOCK & CHAIN
<br />(.SEE NODE 4A)
<br />17 RECEIVING
<br />-
<br />SLIDE BOLT EACH SIDE
<br />(I7B OVERHEAD
<br />(SEE NOTE 19)
<br />18 ROOF IIATCI1
<br />-
<br />2'-6"
<br />3'-0"
<br />-
<br />-
<br />19 ROOF ACCESS
<br />D
<br />3'-0"
<br />6'-0"
<br />1 3/4"
<br />KEYED DEADBOLT WITH THUMB TURN,
<br />FULL WEATHERING & RAIN HOOD
<br />-
<br />-
<br />-
<br />�A) SHUTTERNF
<br />-
<br />LEGEND
<br />ALUM
<br />ALUMINUM
<br />HM
<br />HOLLOW METAL
<br />SC
<br />SOLID CORE
<br />MTL
<br />METAL
<br />TCR
<br />THERMACORE
<br />CAF
<br />CLEAR ANODIZED FINISH
<br />PC
<br />PLASTIC HONEYCOMB CORE
<br />MATERAAI
<br />FINISII
<br />REMARKS
<br />DOOR FRAME
<br />ALUM
<br />ALUM
<br />CAF
<br />FACfOKY /-PIN INTERIOR CYLINDER AND OUTSIDE BLANK
<br />54" NOM CLEAR OPENING. (SEE NOTE 1). PACKAGE HEIGHT 13'-6"
<br />44" NOM CLEAR OPENING; SEE SHEET A1.2 (SEE NOTE 1) PACKAGE HEIGHT 13'-6"
<br />ALUM
<br />ALUM
<br />CAT-
<br />HM
<br />HM
<br />PAINT
<br />STOP FACE MOUNT SFI F CLOSER (PREPAINT TO MARCH INT, DOOR COLOR). BEST 7-PIN MORTISE CYL., PRFPARF DR &
<br />FRAME FOR CONCEALED INSTALLATION; CONNECTION RCQ'D TO FIRL DEFECTION SYSTEM. (SEE NOTE 2.9)
<br />HM
<br />HM
<br />PAINT
<br />-
<br />180 DEGREE VIEWER (SEE NOTE 12), STOP FACE MOUNT SELF -CLOSER, FULL CANOPY, HF.�S, I /-PIN CYL, 'D' HANDLE
<br />AT INTERIOR ABOVE ARROW EXIT DEVICE AT +54" A.F,F. TO CLOSE DOOR (SEE NOTE 24)
<br />HIM
<br />HM
<br />PAINT
<br />STOP FACE MOUNT SELF CLOSER (PPREPAINT TO MATCH INT. DOOR COLOR). BEST 7-PIN MORTISE CYL., PREPARE DR &
<br />FRAME FOR CONCEALED INSTALLATON; CONNECTION RFQ'D TO FIRE DETECTION SYSTEM (SEE NOTE 29)
<br />MTL
<br />MTL
<br />PAINT
<br />DOOR, FRAME & CHUTE IN MARATHON RAM -JET COMPACTOR PACKAGE (WITH SLIDEBCLT & LATCH FOR PADLOCK) BY
<br />G.C., SILL AT +40", INSURE ADEQUATE SLOPE IN CHUTE.
<br />TCR
<br />MTL
<br />PAINT
<br />INSULATED SECTIONAL OVERHEAD DOOR, TWO SLIDE BOLTS AT 36", PADLOCKS EACH SIDE (SEE NODE 9B), VERTICAL
<br />OVERHEAD PARKING, 180' VIEWER CENTERED IN EACH (SFF NOTE 12)
<br />MTL
<br />MTL
<br />PAINT
<br />BES I PADLOCK (SEE NOTE 4A); SAFETY POLE, SCC DETAILS 3 & 4/A1.1; BILCO OR APPROVED EQUAL
<br />HM
<br />HM
<br />PAIN I
<br />BEST 7-PIN CYLINDER, DRIP EDGE, SIGN WORK CAVITY ACCESS LOCATED ON ROOF. DOOR SILL/THRESHOLD TO BE
<br />1'-0" ABOVE FINISHED ROOF.
<br />-
<br />-
<br />VERIFY WHERE REQUIRED, SEE NOIT 8.2 ON SHEET G1,1
<br />GENERAL HARDWARE NOTES
<br />A. SEE DETAIL 4/A51 FOR TYPICAL HEAD DETAILS AT EXTERIOR HOLLOW METAL DOORS & FRAMES IN CMU WALL, U.O.N.
<br />ROOM FINISH SCHEDULE
<br />ROOM
<br />FLOOR
<br />(SEE
<br />NOTE
<br />6)
<br />WALLS
<br />WALL
<br />FINISH
<br />CEILING
<br />OTHER
<br />COLUMNS
<br />DOOR
<br />REMARKS
<br />FRAMES
<br />- _
<br />AND
<br />TRIM
<br />-
<br />43
<br />C)
<br />c
<br />�
<br />w
<br />W
<br />I
<br />�`
<br />I
<br />0
<br />w
<br />Elf
<br />w
<br />w
<br />C)
<br />z
<br />Imo-
<br />m
<br />a
<br />z
<br />W
<br />z
<br />C
<br />c
<br />W
<br />W
<br />-
<br />c
<br />'I
<br />t
<br />C)
<br />C�
<br />U
<br />x
<br />w
<br />a
<br />n-
<br />cn
<br />cn
<br />cn
<br />V)
<br />\
<br />C]
<br />�
<br />U
<br />W
<br />u
<br />Z
<br />C/)
<br />J
<br />J
<br />J
<br />U
<br />-
<br />I-
<br />C!
<br />C
<br />2
<br />d
<br />�
<br />CD
<br />LEI
<br />U
<br />4
<br />�1
<br />C)-cC
<br />a
<br />r�
<br />m
<br />C )
<br />C9
<br />ca
<br />c_
<br />W
<br />r
<br />z
<br />o
<br />W
<br />s
<br />0
<br />>=
<br />�
<br />�
<br />5
<br />�
<br />it
<br />U)
<br />cam,
<br />5
<br />w
<br />Ili
<br />�
<br />w
<br />.•
<br />-J
<br />~
<br />W
<br />L�
<br />'ice-
<br />U7
<br />w
<br />C=
<br />C7
<br />LL
<br />C7
<br />C
<br />U
<br />LL
<br />J
<br />1-
<br />=
<br />d
<br />d
<br />F--
<br />J
<br />d
<br />Z
<br />C>
<br />7'
<br />O of
<br />C D
<br />_
<br />L,J
<br />U)
<br />�
<br />C]
<br />W
<br />«
<br />W
<br />V)
<br />Y
<br />CD
<br />J
<br />tZ.
<br />Z
<br />.1
<br />_J
<br />W
<br />C5
<br />I,_I
<br />V)
<br />O
<br />Y
<br />CD
<br />`. L
<br />l,-I
<br />V)
<br />C�
<br />m
<br />W
<br />V)
<br />m
<br />W
<br />M
<br />�
<br />4
<br />o
<br /><
<br />V)
<br />n'
<br />W
<br />J
<br />0
<br />x
<br />m
<br />C)
<br />,J-_
<br />Q
<br /><C
<br />c+)O
<br />d-
<br />7
<br />Chi
<br />x
<br />w
<br />(l
<br />a
<br />_
<br />a
<br />20
<br />_
<br />C)
<br />d-
<br />x
<br />w
<br />J
<br />w
<br />c
<br />cc
<br />n
<br />=
<br />w
<br />Q
<br />x
<br />W
<br />CAL,
<br />x
<br />W
<br />2n
<br />�
<br />CC
<br />U
<br />x
<br />a
<br />o
<br />o_
<br />N0.
<br />NAME
<br />101
<br />SALES FLOOR
<br />-
<br />102
<br />PROCESSING ROOM
<br />GENERAL FINISH SCHEDULE NOTES
<br />A. NOT USED
<br />B. NOT USED
<br />C. STRAIGHT RUN HILL ON SALES FLOOR 10 BE FULL, ALIGNED TILES WHERE POSSIBLE. OBTAIN MOST RECENT LAYOUT FROM ROSS CONSTRUCTION REPRESENTATIVE
<br />PRIOR 10 INSTALLATION, FOLLOW MANUFACTURER'S INSTALLATION MANUAL, SHADE MATCHING MUST BE CHECKED.
<br />D. Al AEI. DRYWALL, TAPE, FILL AND SAND EXPOSED DRYWAI_I_ JOINIS AND SURFACES TO PRODUCE A SMOOTH UN -TEXTURED SURFACE, PRIMED AND READY FOR
<br />SPECIFIED FINISH. FEATHER COATS ONTO ADJOINING SURFACES SO THAT CAMBER IS MAXIMUM 1/32 INCH. ALL WORK SHALL BE IN ACCORDANCE WITH GYPSUM
<br />ASSOCIATION SPECIFICATION GA 216, FINISH AS SPECIFIED.
<br />E. ALL EXPOSED CONCRETE OR MASONRY WALL SURFACES SHALL BE CLEANED, SEALED AND PAINTED.
<br />F. CONCRETE STALER TO BE APPLIED TO NEW & EXISTING CONCRETE SLABS (INCLUDING THE SALES FLOOR) PER ROOM FINISH & MATERIAL. NOTE 6 & 7.
<br />DOOR AND HARDWARE NOTES
<br />1. STOREFRONT DOORS
<br />A. DOORS % 1, 1A & 2A SHALL BE STANLEY DURA-GLIDE 3000 BI-DINECTIONAL OPERATION AND BE FITTED WITH STANDARD STANLEY HARDWARE.
<br />B, DOORS NO. 2 & 2B SHAI I BE STANI EY DURA-GI Ilk 6000 UNI-DIRECTIONAL OPERATION AND BE FITTED WITH STANDARD STANLEY HARDWARE.
<br />C. DOORS 2 & 1A REQUIRES 7-PIN EXTERIOR/INTERIOR CYLINDER.
<br />DOOR 1 REQUIRES 7-PIN INTERIOR CYLINDER ONLY.
<br />DOORS 2A & 2B TO HAVE NO LOCKSET.
<br />D. ALL EXPOSED HOLES IN STOREFRONT DOORS ARE TO BE FILLED WITH FLUSH BIANKS FINISHED TO MATCH DOOR ALUMINUM
<br />E• ALL STORE FRONT DOORS SHALL BE PROVIDED WITH CODE REQUIRED ACCESSIBILITY SIGNING AS REQUIRED BY LOCAL AUTHORITY.
<br />F. NO THUMB TURNS,
<br />2. INILROR DOORS OPENING TO A PERPENDICULAR WALL MUST HAVE WALL STOPS WITH CONC'LALLD MOUNTING MOUNTED TO SOLID IN WALL BLOCKING. HALER
<br />23OW CONVEX WALL STOP 2-3/9" DIA, 1-3/16" PROJECTION, 626 SATIN CHROME FINISH,
<br />3. DOORS WITHIN ACCESSIBLE PAIH OF 1RAVEL TO BE OPENABLE WITH A SINGLE EFFORT BY LEVER, PANIC BAR OR PUSH/PU11 HARDWARE. DOOR
<br />OPENING HARDWARE TO BE BETWEEN 30" 10 44" A.F.F., EXCEPT AS PROVIDED BY CODE (SEE 1 ABOVE).
<br />4. PADLOCK
<br />A. ROOF HATCH AND COMPACTOR DOOR PROVIDE ONE (1) EACH 7-PIN BEST 91B72-M1 PADLOCK WITH CHAIN (BY G,C.)
<br />B. OVERHEAD DOOR PROVIDE TWO (2) EACH 7-PIN BEST 41B72-M1 PADLOCK WITH CHAIN (BY G.C.) PER DOOR.
<br />5. DOORS OTHER THAN STOREFRONT WHICH RFQUIRF CLOSERS SHALL RECEIVE AN "LCN" #9091 CLOSER, AS INDICATED IN SCHEDULE. DOOR CLOSERS TO BE
<br />ADJUSTED TO PROVIDE FOR A MAXIMUM EFFORT TO OPERATE OF 5 POUNDS FOR INTERIOR DOORS AND 8.5 POUNDS FOR EXTERIOR DOORS. EFFORT MAY
<br />INCREASE TO 15 POUNDS MAXIMUM AT FIRE DOORS, CLOSERS MUST ALLOW THREE SECONDS 10 MOVE DOOR FROM A 70 DECREE OPEN POSITION TO A POINT
<br />3" FROM THE LATCH. IF CONFLICT WITH CODE, FIRE & LIFE SAFETY CODE SHALL PREVAIL. DO NOT USE HOLD OPEN DEVICES.
<br />6. THRESHOLDS SHALL NOT EXCEED 1/2" IN HEIGHT
<br />7. LOCKSETS/LATCHSETS
<br />A, INTERIOR LOCKSETS TO BE BEST #93K7AB14C626 W/ CURVED RETURN LEVERS LOCKSETS 10 AVIF BEST 7 PIN CYLINDER
<br />B. INTERIOR LAICHSEIS TO BE BEST #93KON14C626 W/ CURVED RETURN LEVERS
<br />C. MANAGER OFFICE AND EQIPMENT CLOSET TO RECEIVE BEST #93K7-D-14C626 W/ CURVED RETURN LEVERS AND BEST 7-PIN CYLINDER
<br />D. CASH OFFICE TO RECEIVE BEST 45117-TD-14-11-626 MORTISE LOCK W/ INTERLOCKING DEADBOLT COMBINATION. BEST 7-PIN CYLINDER W/ CURVED
<br />RETURN LEVERS
<br />E. All I ATCI ISFT AND I OCKSCTS TO BE BEST. NO SUBSTITUTIONS WILL BE ACCEPTED
<br />8. WOOD AND H.M. DOORS TO HAVE 3 FULL BEARING MORTISE HINGES WITH NON REMOVABLE HINGE PINS, DOOR CLOSERS, AND DOOR STOPS (INTERIOR DOORS),
<br />FINISH US26D (SAIIN CHROME). HINGES ON All EXTERIOR HIM MAN DOORS ARE TO BE STAINLESS STEEL.
<br />9. HOLLOW METAL FRAMES SHALL BE 18 GA. PRESSED, FLUSH TYPE WITH MITERED AND WELDED CORNERS. CASH OFFICE FRAME SHAII BE 16 GA. H.M. FLUSH
<br />TYPE WITH DOUBLE STUDS AT JAMBS, FRAMES ARE TO BE REINFORCED AND PREPARED FOR HARDWARE. PROVIDE 4" HEAD FOR FRAMES IN EXTERIOR CMU
<br />OPENINGS WHERE APPROPRIATE TO MATCH MASONRY COURSING,
<br />10, HM DOORS ARE TO BE 18 GA., FACTORY PRIMED STEEL, FLUSH TYPE WITH INSULATED WEATHER SEALED CORE; STIFFENING; HARDWARE REINFORCING; CLOSED
<br />TOP & BOTTOM CHANNELS; AND HANDED FOR INDICATED SWING, DO NOT USE UNIVERSAI_ TYPE DOORS.
<br />11, SOLID CORE WOOD DOORS SHALL BE PAINT GRADE BIRCH SKINS WITH SOLID STAVE CORES.
<br />12. DOOR VIEWER TO BE ADVANCED SAFETY DEVICES MODEL #DS238-SLVR.
<br />13. DOOR TYPE 'IF" SHALL RECEIVE A 4%20"H VISION LIFE IN A WELDED STEEL FRAME. FINISH TO MATCH DOOR. SEE DOOR REMARKS FOR GLASS TYPE: CLEAR
<br />OR ONE-WAY.
<br />14. DOOR TYPES "C" "F" & "G" SHALL RECEIVE ON THE HALL SIDE A 12" KICK PLATE BY BROOKLINE INDUSTRIES. FINISH BMHA 626 W/ COUNTERSUNK SCREW
<br />HOLES.
<br />15. DOOR "B" TO BE ELIASON, EASY -SWING P-11 PLUS (PLASTIC HONEYCOMB CORE), 103 'WHITE' FINISH WITH 904 CENTER WINDOW SET IN 103 'WHITE'
<br />MOLDING, AND PAINTED HOLLOW METAL FRAME, WITH 5X18 JAMB GUARDS
<br />16. GENERAL CONTRACTOR TO PROVIDE CONSTRUCTION CORES FOR ALL EXTERIOR DOORS PRIOR 10 TURN OVFR. AT TIME OF TURN OVER CONTRACTOR IS TO TURN
<br />OVER TO ROSS STORE MANAGER CORE EXTRACTION KEY.
<br />17, ROSS STORE MANAGER TO BE RESPONSIBLE FOR REKEYING STORE.
<br />18, SAIFS FLOOR EXIT DOORS NO. 3 AND NO, 5 ARE TO BE EQUIPPED WITH THE ALARM LOCK PUSH BAR MODEL 715 DELAYED EXIT DEVICE WITH BEST 7-PIN
<br />MORTISE CYLINDER AND CONCEALED INSTALLATION USING VON DUPRIN EPT-10 POWER TRANSFER HINGE AND DETECTION SYSTEM WITH TIME -DELAY BY-PASS
<br />CONTROL, SEE FRAME PREP DETAILS 1 & 2 / DE1.0. (INSTALL PER MANUFACTURER'S WRITTEN INSTRUCTIONS). IF STORE REQUIRES HURRICANE SHUTTERS
<br />IHEN DOOR #3 IS TO BE EQUIPPED WITH INSIDE/OUTSIDE KEY CONTROL IN ADDITION TO DELAYED EXIT EGRESS DEVICE.
<br />c r c - -
<br />19. DOOR E IS A �91 SERIES THERMACORE INSULATED STEEI SECTIONAL - -
<br />0 AL DOOR BY THE OVERHEAD DOOR CORPORATION, DALLAS, TEXAS; 8 0' X 8 0;
<br />STANDARD BULB -TYPE BOTTOM SEAL AND OPTIONAL HEADER SEA[- AND JAMB WEATHERSTRIPPINC; 2" TRACK; MANUAL 011LRA110N; COLOR: WHITE; WITH TWO (2)
<br />INTERIOR MOUNTED SLIDE LOCKS, ONE AT EACH SIDE AT +36' AFF. INCLUDE TWO (2) HIS1 418/2 PADLOCKS.
<br />20. EXIT DOOR N0. 4 IS TO BE EQUIPPED WITH THE ARROW 330 PANIC DEVICE WITH LOW HAIIFRY ALERT, BEST 7-PIN CYLINDER AND BMHA 626 FINISII,
<br />21. ANY QUESTION OR PROBLEMS W/ LOCKING HARDWARE SHOULD BE DIRLCI1-1) 10: BEST LOCK CORPORATION (SEE SHEET AO.0 FOR CONTACT INFO.).
<br />22. UNLESS OTHERWISE REQUIRED BY LOCAL AUTHORITY, INSTALL ACCESSIBLE TOILET ROOM SIGNING CENTERED AI 60" AFF ON THE WALL ADJACENT TO THE
<br />STRIKE SIDE OF THE DOOR, MINIMUM 9"x9" WITH CONTRASTING AND RAISED PICTOGRAPH, SANS SERIF LETTERING AND GRADE 2 BRAILLE. (ROSS STANDARD
<br />ACCFSSIBI F TOILET ROOM SIGNING WILL BE PROVIDED FOR g.c• INSTALLATION THROUGH ROSS CONSTR. RFPRFSFNTATIVE) ALL OTHER SIGNING REQUIRED BY ADA
<br />OR LOCAL AUTHORITY, WHETHER Al IOILET ROOMS OR ELSEWHERE IN THE BUILDING, MUST BE PROVIDED AND INSTALLED BY TIFF GENERAL
<br />CONTRACTOR.
<br />23, DOORS NO, 6 AND 20 SHALL BE CONTROLLED BY A IRILOGY T2 LEVER DIGITAL LOCK (DL 2700 IC / 26D) BY ALARM LOCK SYSTEMS (SFF SHEET A0.0 FOR
<br />CONTACT INFO). USE BEST 7-PIN CORE.
<br />24, ALL EXTERIOR DOORS ARE 10 BE FULLY WEATHERSTRIPPFD INCLUDING A RAIN DRIP AND DOOR BOTTOM, HAVE ACCESSIBLE THRESHOLDS (EXCEPT DOOR 19)
<br />AND CONCRETE LANDINGS (OR SIDEWALK). EXTERIOR DOORS OPENING ON TO TRAFFIC AREAS ARE TO BE PROTECTED BY PIPE BOLLARDS.
<br />25. PROVIDE VON DUPRIN - MODEL 5211 ELECFRIC STRIKE WITH LOCKNETICS (SCHLAGE) 701 RD MOMENTARY WALL SWITCH (800) 950-4573.
<br />26. SECURITY SHUTTERS - ANODIZED ALUMINUM SECURITY STUTTER BY QMI SECURITY SOLUTIONS, VERTICAL TRACK MOUNTED AT INTERIOR TO STOREFRONT
<br />MULLIONS, LOCKING MECHANISM AND LIFTS MOUNTED AT 36" A.F.F. AT DOORS AND AT 27" A,F.F. AT WINDOWS; SLAT TYPE AL5-E; STYLE PUNCH 51; 10"
<br />HOUSING MOUNTED TO STOREFRONT VERTICAL MULLIONS, CONTROL TYPE SPRING A-7-13, VERIFY WHERE REQUIRED, SUPPLIED AND INSTALLED BY ROSS LP.
<br />ROOM FINISH &MATERIALS NOTES
<br />COORDINATE ALL ORDERS AND DELIVERIES WITH THE LISTED VENDORS, NO SUBSTITUTIONS Will BE ALLOWED,
<br />1, NEW CONCRETE MUST BE TREATED WITH THE CRE ESEAL CS2000 SPRAY APPLY SYSTEM (15 YR. WARRANTY) APPLIED IN ACCORDANCE WITH MANUFACTURERS
<br />NSIRUCTIONS. THE CS2000 2-DAY SYSTEM MUST BE USED ON EXISTING SLABS.
<br />2, SLABS MUST BE DESIGNED AND PREPARED TO TEST AND MAINTAIN MOISTURE VAPOR EMISSIONS AT OR BELOW 5-LBS PER 1000 SF PER 24-HRS USING THE
<br />CALCIUM CHLORIDE METHOD (ILSI RESULTS SHALL BE PROVIDED TO ROSS CONSTRUCTION MANAGER), THE PROCESSING ROOM, ELECTRICAL ROOM AND OTHER
<br />AREAS OF THE SLAB NOT RECEIVING FINISH TILE OR CARPET ARE TO RECEIVE A TWO COAT APPLICATION OF A PENETRATING LOW VISCOSITY EPDXY OR ACRYLIC
<br />SEALER; AT EXISTING SLABS ADD A LIGHT -GRAY COLOR, SUCH AS GARLAND 122 LICHT-GRAY, 10 EPDXY FOR UNIFORM FLOOR FINISH.
<br />3. NEW CONCRETE MUST BE TREATED WITH THE CRETESEAL CS2000 SPRAY APPLY SYSTEM (15 YR. WARRANTY) APPLIED IN ACCORDANCE WITH MANUFACTURERS
<br />INSTRUCTIONS, THE CS2000 2-DAY SYSTEM MUST BE USED ON EXISTING SLABS.
<br />r• r
<br />c
<br />4, SLABS MUST BE DESIGNED AND PREPARED TO TEST MOISTURE -
<br />AND MAINTAIN MOhTJRE VAPOR EMISSIONS AT OR BELOW 5 LBS PER 1000 SF PER 24-IIR� USING THE r r c .a
<br />CALCIUM CHLORIDE METHOD. TEST RESULTS SHALL BE PROVIDED CONSTRUCTION
<br />TO ROSS ON�TRUCTION MANAGER), THE PROCESSING 'T ( ) ROOM, LLLG RICAI_ ROOM AND OTHER
<br />AREAS OF THE SLAB NOT RECEIVING FINISH TILE OR CARPET ARE TO RECEIVE A TWO -COAT APPLICATION OF A PENETRATING LOW VISCOSITY EPDXY OR ACRYLIC
<br />SEALER; AT EXISTING SLABS ADD A LIGHT -GRAY COLOR, SUCH AS GARLAND 122 LIGHT-CRAY, TO EPDXY FOR UNIFORM I-LOOR FINISH.
<br />Proj. Mgr.
<br />JU
<br />Job. Capt.
<br />SG
<br />Drawn by
<br />JT
<br />Rev'd by
<br />RB
<br />RON BARR, A.I.A.
<br />STATE OF FLORIDA
<br />AR 0016160
<br />S
<br />cc C
<br />S = L
<br />U
<br />i a i
<br />w
<br />i D i
<br />z
<br />O 5
<br />Q o
<br />z X c
<br />5
<br />m F
<br />��Wt
<br />o a F
<br />Z
<br />1
<br />T C
<br />C COPYRIGHT 2012
<br />BARR ARCHITECTURAL STUDIO
<br />,f 1111,
<br />Ing,
<br />A
<br />liu
<br />a
<br />t
<br />Ip
<br />I
<br />6� RIP
<br />1"
<br />'
<br />L
<br />kia
<br />`I
<br />A�°
<br />al
<br />�I FS
<br />I
<br />u
<br />hl
<br />imM1�S
<br />Revisions:
<br />CADFILE No.
<br />s
<br />ICI
<br />aE
<br />j,
<br />�]
<br />a1„lII
<br />h>R •a a
<br />jj
<br />Al9
<br />n !
<br />a Y 1ill
<br />li 1.40
<br />a d
<br />62
<br />0
<br />150
<br />C7
<br />(0
<br />C
<br />CIO
<br />4J
<br />�=
<br />N
<br />C:
<br />u_
<br />N
<br />T
<br />V
<br />ai
<br />a
<br />W
<br />'
<br />a
<br />d'
<br />Lo
<br />�
<br />401
<br />C,
<br />,E
<br />.
<br />"'
<br />,C
<br />as
<br />uo
<br />3
<br />�
<br />E
<br />L
<br />o
<br />0
<br />L
<br />�
<br />�
<br />U
<br />ACA
<br />Lo
<br />m
<br />A-
<br />U
<br />a
<br />N
<br />U
<br />L0
<br />i
<br />Sheet Title
<br />ROOM FINISH
<br />AND DOOR
<br />SCHEDULES
<br />Scale: AS NOTED
<br />Date: Sheet No.
<br />01-31-2013
<br />Project No.
<br />A6.0
<br />12-027
<br />
|