|
6
<br />5
<br />ri
<br />cn
<br />r-i
<br />r-1
<br />kD
<br />r-I
<br />0
<br />N
<br />1/2" STUCCO FINISH OVER PAPER
<br />BACK LATH SYSTEM SIMILAR TO
<br />CLARK DIETRICH GALVANIZED
<br />STEEL PLASTERISTUCCO BASE
<br />PERM -A -BARRIER BY
<br />W.R. GRACE OR EQUAL �:l -
<br />FINISH AS SCHEDULED; -•I'
<br />REF SHEET A3.0
<br />1/2" GYP BOARD
<br />MIN 20GA 3 5/8" MTL
<br />STUDS @ 24" O.C. 7
<br />{
<br />TOOLED MORTAR JOINT
<br />MIN R-19 INSULATION
<br />I
<br />REINFORCE AND GROUT;
<br />REFSTRUCTURAL
<br />W1 EXTERIOR WALL
<br />EXTERIOR WALL
<br />W1 5/8" PLYWOOD @ INTERIOR SIDE
<br />4 , PARTITION TYPES
<br />11/2if = 1'-011
<br />12" MAX
<br />SLOPF 1/8" PER FT
<br />20 GA. METAL STI
<br />FRAMING @ 24" C
<br />INTERIOR WALL
<br />FINISH AS
<br />SCHEDULED
<br />SUBSTRATE PER
<br />WALL TAG (MOIS•
<br />RESISTANT
<br />GYP BD, @ WET
<br />LOCATIONS)
<br />3� 5/8 �
<br />(6" @ PLUMBING) 6" @ BEVERAGE BAR EPDXY PAINT
<br />INTERIOR SIDE OF
<br />NTD: FACE OF 3 5/8" CMU BLOCK WALL
<br />STUD AT BEVERAGE 3 5/8"lof
<br />BAR TO BE 6" OFF CMU WALL WITH
<br />REAR WALL REINFORCEMENT AND
<br />GROUT; REF STRUCTURAL
<br />3 5/8" 20 GA. METAL
<br />STUD FRAMING @ TOOLED MORTAR JOINT
<br />24" O.C.
<br />INTERIOR WALL TSTUCCO TO MATCH
<br />FINISH AS BUILDING FINISH
<br />SCHEDULED
<br />1/2" GYP BOARD
<br />INTERIOR PARTITION W3 INTERIOR PARTITION W4 DUMPSTER ENCLOSURE WALL
<br />W2 1/2" GYP BOARD
<br />NOTES:
<br />INTERIOR PARTITION INTERIOR P�ARTION1. ALL CMU & MORTAR TO BE MANUFACTURED WITH INTEGRAL
<br />W 5/8" PLYWOOD @ W3 5/8° PLYWOOD WATER RESISTANCE
<br />ELECTRICAL SIDE ONLY ELECTRICAL SILY 2. ALL INTERIOR PARTITIONS TO DECK UNLESS OTHERWISE NOTED
<br />3. ALL GYPSUM BOARD TO BE INSTALLED VERTICALLY
<br />TILE ON THIN -SET MORTAR BED
<br />SEALANT
<br />THIN SET BOND COAT OR
<br />� SI nDF 1/R" PER1=T
<br />PRIMER PER MANUFACTURER'S
<br />°
<br />-
<br />-
<br />REC O MMENDA TIONS
<br />-
<br />d
<br /><
<br />WATERPROOFING
<br />-
<br />9
<br />MEMBRANE
<br />GRADE
<br />CONIC SLAB. REF STRUCT. CONC. SLAB ON GRADE APPLICATION
<br />FOR RECESSES AT
<br />DRAINS
<br />RESTROOM FLOOR DRAIN DETAIL
<br />N.T.S.
<br />O
<br />NULMJ EH
<br />SN1 '�'' SN2
<br />A
<br />1/4" ACRYLIC BACKPLATE
<br />FOAM TAPE
<br />} 1/32" RAISED GRAPHICS
<br />SN5%, 1/40" RAISED GRADE 2 BRAILLE
<br />1/4" ACRYLIC
<br />BACKPLATE
<br />- RAISED IMAGE/
<br />BRAILLE PATTERN
<br />\ FOAM TAPE
<br />1/32" RAISED
<br />GRAPHICS
<br />1/32" RAISED
<br />COPY
<br />1/40" RAISED
<br />GRADE 2 BRAILLE
<br />RESTROOM/EXIT SIGNAGE SPECIFICATIONS
<br />1. LETTERS AND NUMERALS SHALL BE RAISED 1/32", UPPER CASE, SANS SERIF OR SIMILAR SERIF TYPE AND
<br />SHALL BE ACCOMPANIED WITH GRADE 2 BRAILLE. RAISED CHARACTERS SHALL BE AT LEAST 5/8" HIGH, BUT NO
<br />HIGHER THAN 2". PICTOGRAMS SHALL BE ACCOMPANIED BY THE EQUIVALENT VERBAL DESCRIPTION PLACED
<br />DIRECTLY BELOW THE PICTOGRAMS. THE BORDER DIMENSION OF THE PICTOGRAM SHALL BE 6" MINIMUM IN
<br />HEIGHT.
<br />2. THE CHARACTERS AND BACKGROUND OF SIGNS SHALL BE EGGSHELL, MATTE, OR OTHER NON -GLARE FINISH.
<br />CHARACTERS AND SYMBOLS SHALL CONTRAST WITH THEIR BACKGROUND - EITHER LIGHT CHARACTERS ON A
<br />DARK BACKGROUND OR DARK CHARACTERS ON A LIGHT BACKGROUND.
<br />3, WHERE PERMANENT IDENTIFICATION IS PROVIDED FOR ROOMS AND SPACES, SIGNS SHALL BE INSTALLED ON
<br />THE WALL ADJACENT TO THE LATCH SIDE OF THE DOOR. WHERE THERE IS NO WALL SPACE TO THE LATCH
<br />SIDE OF THE DOOR, INCLUDING DOUBLE LEAF DOORS, SIGNS SHALL BE PLACED ON THE NEAREST ADJACENT
<br />WALL. MOUNTING HEIGHT SHALL BE 60" A.F.F. TO THE CENTERLINE OF THE SIGN. MOUNTING LOCATION FOR
<br />SUCH SIGNAGE SHALL BE SO THAT A PERSON MAY APPROACH WITHIN 3" OF SIGNAGE WITHOUT
<br />ENCOUNTERING PROTRUDING OBJECTS OR STANDING WITHIN THE SWING OF A DOOR.
<br />W1
<br />z
<br />A.1
<br />14
<br />SIGNAGE
<br />SN1
<br />MEN'S RESTROOM (REFERENCE A2.0)
<br />SN2
<br />WOMEN'S RESTROOM (REFERENCE A2.0)
<br />SN3
<br />EMPLOYEES ONLY
<br />SN4
<br />THIS DOOR IS TO REMAIN UNLOCKED WHEN
<br />BUILDING IS OCCUPIED. (NOTE: THE SIGN SHALL
<br />BE IN LETTERS 1 INCH HIGH ON A CONTRASTING
<br />BACKGROUND.)
<br />SN5
<br />TACTILE EXIT SIGN PER LOCAL AHJ.
<br />GENERAL NOTES
<br />1. CONTRACTORS SHALL NOT SCALE THESE DRAWINGS. IN THE EVENT OF OMISSION OF NECESSARY DIMENSIONS
<br />THE CONTRACTORS SHALL NOTIFY THE CONSTRUCTION PROJECT MANAGER.
<br />2. CONSTRUCTION PROJECT MANAGER SHALL VERIFY ALL BUILDING DIMENSIONS, AND SITE GRADES PRIOR TO
<br />START OF WORK.
<br />3. VERIFY SIZE, LOCATION, AND CHARACTERISTICS, OF ALL WORK AND EQUIPMENT TO BE FURNISHED BY OWNER
<br />OR OTHERS, WITH THE MANUFACTURER OR SUPPLIER BEFORE ANY CONSTRUCTION PERTAINING TO SAME IS
<br />BEGUN.
<br />4. ALL DIMENSIONS ON PLANS UNLESS OTHERWISE NOTED ARE TO OUTSIDE FACE OF SIP, CMU BLOCK OR
<br />STRUCTURAL SHEATHING.
<br />5. 2" AIR SPACE BETWEEN COOLER WALL AND BUILDING WALL, OR ANY EQUIPMENT ADJACENT TO COOLER. WALK-IN
<br />COOLER SUPPLIED BY 7-ELEVEN, INC, INSTALLATION TO BE DETERMINED BY CONSTRUCTION PROJECT MANAGER.
<br />6, FIRE EXTINGUISHER: #10 CLASS ABC WITH UL RATING 4A-60BC. SURFACE MOUNTED ON WALL WITH
<br />MANUFACTURERS ALL STEEL WALL BRACKET. JL INDUSTRIES INC. (COSMIC 10E) OR APPROVED EQUAL WITH
<br />INSPECTION TAG AS REQUIRED BY LOCAL CODES.
<br />7. ALL WALL FINISHES IN THE MERCHANDISE / SALES AREAS SHALL BE FRP WALL PANEL "FRP-A" UNLESS NOTED
<br />OTHERWISE ON THE FLOOR PLAN. (REFERENCE SHEET A3,0 FOR MATERIALS SCHEDULE)
<br />8. CONTRACTOR TO PROVIDE AND INSTALL WALL BACKING FOR WALL HUNG FIXTURES AND TOILET ACCESSORIES.
<br />9. CONTRACTOR TO PROVIDE AND INSTALL IVES #405 (OR APPROVED EQUAL) COAT HOOKS; REF EF SHEETS. INSTALL
<br />2 IN OFFICE, 3 IN BACKROOM, AND 1 IN EACH RESTROOM. LOCATION TO BE DETERMINED BY CONSTRUCTION
<br />PROJECT MANAGER. SEE DOOR HARDWARE SCHEDULES.
<br />10. APPLY 3M SUN CONTROL WINDOW FILMS @ ALL SOUTH, EAST, AND WEST FACING GLASS (3M-1). NOTE NO FILM
<br />SHOULD BE APPLIED TO THE STOREFRONT DOORS. (REFERENCE SHEET A3,0 FOR MATERIALS SCHEDULE)
<br />11. CERAMIC TILE FLOORING WITH 33% OFFSET PER MATERIALS SCHEDULE ON A3.0. 24" EDGE OF TILE TO RUN
<br />PARALLEL WITH ENTRY STOREFRONT. BEGIN FULL SIZE TILE AT EDGE OF ENTRY THRESHOLD.
<br />12. G.C. TO FURNISH AND INSTALL RIS BACKBOARD AT ISP DESK. REFERENCE MATERIALS SCHEDULE ON SHEET A3.0.
<br />13. RUB PARGE ALL LIGHTPOLE BASES.
<br />t
<br />2.0
<br />24'-0" 16'-1" 23'-111/4" 3'-4"
<br />6' - 3" 6' - 3" 4 3 4' -3 3/4"
<br />A2,0
<br />A6.0 DOWNSPOUT TYP. <W1A
<br />I
<br />0
<br />a
<br />>, 5X
<br />W1A '
<br />° � N
<br />ICE FREEZER x CO-OHll
<br />ZEI
<br />O
<br />11 109 a Q "'� a - a ---� ELECTRICAL
<br />� `w1
<br />13'-4"
<br />16'-8"
<br />1.0
<br />Z 1 FLOOR PLAN
<br />1 /A u _ 1 1-nit
<br />T-5
<br /><5 A5.0
<br />J =O 6 3 =O
<br />A5.1 > 108
<br />r-
<br />BEVERAGE BAR
<br />-------- ---- ---------------------------------------- \ 8
<br />s WOMEN_
<br />108
<br />OH 106 w2A
<br />PROFILE OF CEILING. J \
<br />CLOUD ABOVE
<br />L - - - - -
<br />106 _ -
<br />r----I I LINE OF 11 � r-
<br />-------------------------------------- �� SN2 FE
<br />BULKHEAD - - -
<br />ABOVE - vu2 101 B
<br />O O Z
<br />C c'J
<br />® N
<br />I Ln W2 r-
<br />0 / SN1 SN3 41
<br />-------- 105 107 r-
<br />COFFEE ISLAND _MEN 'v
<br />PROFILE SKYLIGHT R.O. ABOVE - / 105 Dairy
<br />2 / 6 Crate
<br />rim
<br />2
<br />3 <5 A5.1 3> O RO o w, H
<br />I- A2.0 / v O
<br />H 4 H p
<br />o
<br />McLanLJ e, <1 A4,1
<br />Tote - U o
<br />II SALES
<br />r
<br />I I
<br />I i
<br />I I
<br />I I
<br />I I
<br />A5.0
<br />3
<br />11 0,
<br />A7.0 0
<br />P�
<br />F
<br />Oo
<br />102 /� EU]
<br />0
<br />MERCHANDISE
<br />�� - W2
<br />� - - 2' - 5 3/4" 8' - 6 1 /4"! v� _ ' - 7 3/4 i0
<br />SN3 CO2TANK
<br />0 _ J c� INSTALLED/ANCHOF
<br />1 PER MANUFACTURE
<br />i A7.0 Q 3' - 5" _ SPECS BY GC.
<br />\ 00 104 PROVIDE SHUT OFF
<br />WHERE CO2 SUPPL'
<br />_ - Q'� J _ LINES PENETRATE
<br />N THE BUILDING. LABE
<br />A5.0 1> r CO2 PROVIDED BY NUCC
<br />PROFILEn SKYLIGHT O <5 A5.2 2>
<br />R.O. ABOVE
<br />3
<br />®❑ A5.0 2 F_ v
<br />I I
<br />Ai 11 1/4"
<br />BACK
<br />(FE ROOM °
<br />TILE FLOORING 7 -1
<br />PER MATERIALS A5,3 104
<br />SCHEDULE L
<br />24" EDGE OF TILE TO RUN PARALLEL WITH 3 OFFICE Cn
<br />ENTRY STOREFRONT. BEGIN FULL SIZE TILE 33% i o
<br />AT EDGE OF ENTRY THRESHOLD OFFSET 103
<br />F I
<br />E C� SN4 - - <4 A5.2 11 wz "v
<br />SN5
<br />ff 0
<br />101
<br />5 1 18 8' - 6 3/4' 6' .5 1/4" D O r-
<br />A7.0 A6.0 A7.0 2
<br />8.33% MAX A6,0 8.33% MAX
<br />- - - -CANOPY ABOVE - SLOPE - - J SLOPE
<br />P- UP
<br />10'-4" 16'-2" 10'-10" o 000000000000 16'-8"
<br />0 0000000000000
<br />00000000000000
<br />000000000000000
<br />70'-8" 00000000000000
<br />o0000000000000
<br />000 00000000000
<br />1 REFER TO CIVIL DRAWINGS
<br />1.2 1.1 FOR EXACT REQUIREMENTS 2.0
<br />A4.0 FOR RAMP, STRIPING AND
<br />TACTILE SURFACE LAYOUT
<br />E
<br />C
<br />A
<br />Aft
<br />106 N 37TH STREET, SUITE C
<br />ROGERS, ARKANSAS 72756
<br />W W W.BATESARCH ITECTS.CO M
<br />TEL: 479.633.8165
<br />Copyright 2016 Bates & Associates, Architects
<br />Drawings and Specifications as instruments of service are and shall remain
<br />the property of the Architect. They are not to be used on other projects or
<br />extensions to this project except by agreement in writing and with
<br />appropriate compensation to the Architect.
<br />Contractor is responsible for confirming and correlating dimensions at job
<br />site; the Architect will not be responsible for construction means, methods,
<br />techniques, sequences or procedures, or for safety precautions and
<br />programs in connection wRh the project.
<br />SITE/STORE #:
<br />37745
<br />CONSTRUCTION MANAGER
<br />CREIGHTON COMMERCIAL DEVELOPMENT
<br />900 SW PINE ISLAND ROAD, SUITE 202
<br />CAPE CORAL, FL 33991
<br />TENANT
<br />7-ELEVEN INC.
<br />1722 ROUTH ST. SUITE 1000 DALLAS, TX 75201
<br />CONTACT: DANIELTUBB
<br />STRUCTURAL CONSULTANT
<br />SELECT STRUCTURAL
<br />12573 NEW BRITTANY BLVD FORT MYERS, FL 33907
<br />CONTACT: SHAWN ANDERSON
<br />MEP CONSULTANT
<br />WALTER J. FITZGERALD, P.E.
<br />2566 NEBRASKA AVE., PALM HARBOR, FL 34684
<br />CONTACT: (813) 785-7526
<br />O
<br />QN
<br />�z
<br />N
<br />UJ
<br />LLL o 0)
<br />Q m
<br />� L.L
<br />Z W
<br />gO
<br />L w a
<br />Z_
<br />06
<br />Ua U
<br />C)N
<br />I� M Z
<br />U
<br />M
<br />A
<br />r
<br />AR97905
<br />BRED b
<br />Architect Name - RYAN M FAUST
<br />Architect Number - AR97905
<br />THE SEAL AND SIGNATURE APPLY ONLY TO THE DOCUMENT TO WHICH
<br />TH EY ARE AFFIXED AND WE EXPRESSLY DISCLAIM ANY RESPONSIBILITY FOR
<br />ALL OTHER PLANS, SPECIFICATIONS, ESTIMATES, REPORTS OR OTHER
<br />DOCUMENTS OR INSTRUMENTS RELATING TO OR INTENDED TO BE USED
<br />FOR ANY PART OR PARTS OF THE PROJECT.
<br />REVISIONS
<br />NO. DATE DESCRIPTION
<br />PROJECT NUMBER: 16018
<br />RELEASE DATE: 03/31/2016
<br />FLOOR PLAN
<br />RESTROOM/EXIT WALL SIGNAGE & SYMBOLS
<br />N.T.S.
<br />5
<br />9
<br />3
<br />2
<br />1
<br />
|