|
A
<br />B
<br />C
<br />a
<br />E
<br />F
<br />SUPPLY DUCT FROM AIR SUPPLY DUCT FROM AIR
<br />VOLUME CONTROL BOX VOLUME CONTROL BOX
<br />BELLMOUTH BELLMOUTH
<br />CONNECTION 7'-O" MIN. IF AUX. CONNECTION
<br />FLEXIBLE DUCT SEE NOTE 1 VD IS REQUIRED SEE NOTE 1
<br />O 5'-0"MIN., V-"
<br />MAX. LENGTH FRONT VIEW SECTION A -A
<br />7%0" MIN. IF AUX. SEE NOTES 3
<br />STRAIGHT LENGTH STRAIGHT LENGTH MINIMUM OF TWO VD IS REQUIRED AND 4
<br />MINIMUM OF TWO DUCT DIAMETERS. INSTALL PER DETAIL B
<br />DUCT DIAMETERS IF ADEQUATE SPACE NOT AVAILABLE.
<br />VD :VD
<br />I
<br />FLEXIBLE DUC
<br />SEE NOTE 4 5'-0" MIN., 6'-0"
<br />MAX. LENGTH AUXILIARY VD
<br />SHEET METAL SEE NOTE 3.
<br />COLLAR STRAIGHT LENGTH
<br />EQUALIZING GRID MINIMUM OF ONE
<br />DUCT DIAMETER
<br />SEE NOTE 5 INTEGRAL VOLUME DAMPER SEE NOTE 2
<br />SEE NOTE 6
<br />SEE NOTE 5
<br />TYPES LD TYPES CD
<br />NOTES:
<br />1. SIDE BRANCH CONNECTION SHOWN. USE SIMILARLY ARRANGED TOP OR BOTTOM BRANCH CONNECTION AS REQUIRED. TEE
<br />CONNECTION ALLOWED ONLY WHERE DUCT HEIGHT IS NOT ADEQUATE FOR BELLMOUTH.
<br />2. MAY BE REDUCED ONLY WHEN REQUIRED BY SPACE LIMITATION. PROVIDE SHEET METAL TRANSITION AS REQUIRED BETWEEN
<br />FLEXIBLE DUCT AND SHEET METAL COLLAR IF DIFFUSER DOES NOT HAVE ROUND CONNECTION.
<br />3. PROVIDE CONCEALED CEILING DAMPER REGULATOR OR CEILING ACCESS DOOR WHERE VD IS LOCATED ABOVE
<br />INACCESSIBLE CEILING.
<br />4. VD LOCATION FOR DIFFUSER LOCATED IN ACCESSIBLE CEILING.
<br />5. PROVIDE BORDER STYLE AND DIFFUSER FACE COMPATIBLE WITH CEILING SYSTEM.
<br />.
<br />REFER TO ARCHITECTURAL DRAWINGS AND DRAWING SCHEDULE.
<br />DIFFUSER INSTALLATION
<br />SCALE: NONE
<br />DAMPER PROTECTED WITH 1/16" CERAMIC CODED
<br />BOTH SIDES & HELD OPEN WITH 160" F FUSIBLE LINK
<br />GALVANIZED STEEL AIR DUCT
<br />JOISTS
<br />HANGER WIRE 8' MAX. UNLESS
<br />OTHERWISE
<br />DUCT SUPPORT, SPECIFIED
<br />C.R. CHANNEL
<br />FIRE RATED AIR DIFFUSER
<br />TILE AREGISTER
<br />GRILLE
<br />HINGED SHEET STEEL DAMPER
<br />DIFFUSER FLANGE LAPS STEEL
<br />(LABEL NOT REQUIRED; HOWEVER, THE U.L. FIRE RESISTANCE DIRECTORY DEFINES THE USE
<br />OF AND LIMITS OF APPLICATION OF THESE DEVICES.) /
<br />DIFFUSER
<br />DROP
<br />BLADE
<br />CEILING
<br />CORROSION
<br />RESISTANT
<br />HINGE
<br />DIFFUSER
<br />REGISTER
<br />GRILLE
<br />DETAIL OF CEILING DAMPER
<br />FOR UNLINED OR UNINSULATED DUCTWORK
<br />SCALE: NONE
<br />BACKDRAFT
<br />DAMPER
<br />DUCT
<br />SHEET METAL
<br />FAN
<br />SEE NOTE 3
<br />FLEXIBLE DUCT
<br />SEE NOTE 1 FLEXIBLE DUCT
<br />5'-O" MAX. LENGTH AUXILIARY VD WHERE SHOWN ON DRAWINGS.
<br />SEE NOTE 2 SEE NOTE i PROVIDE CONCEALED CEILING DAMPER
<br />SHEET METAL REGULATOR OR CEILING ACCESS
<br />COLLAR STRAIGHT LENGTH DOOR WHERE ABOVE INACCESSIBLE CEILING
<br />SHEET METAL EQUALIZING GRID MINIMUM OF ONE
<br />COLLAR DUCT DIAMETER
<br />INTEGRAL VOLUME DAMPER
<br />SEE NOTE 5 TEE BAR FOR
<br />LAY -IN TYPE SEE NOTE 5
<br />DETAIL 'A' SEE NOTE 5 DETAILS'
<br />NOTES:
<br />1. PROVIDE FLEXIBLE DUCT ONLY FOR LAY -IN CEILING INSTALLATION OR AS REQUIRED FOR ALIGNMENT WITH CEILING PATTERN
<br />2. PROVIDE SHEET METAL TRANSITION BETWEEN FLEXIBLE DUCT AND SHEET METAL COLLAR IF DIFFUSER DOES
<br />NOT HAVE ROUND CONNECTION.
<br />3. BELLMOUTH CONNECTION FOR ROUND BRANCH DUCT. SMACNA BOOT FOR RECTANGULAR BRANCH DUCT.
<br />4. SIDE BRANCH CONNECTION SHOWN. USE SIMILARLY ARRANGED TOP OR BOTTOM BRANCH CONNECTION AS REQUIRED.
<br />S. PROVIDE BORDER STYLE AND DIFFUSER FACE COMPATIBLE WITH CEILING SYSTEM. REFER TO ARCHITECTURAL DRAWINGS AND DRAWING SCHEDULE.
<br />6. ROUND BRANCH DUCT SHOWN. RECTANGULAR BRANCH DUCT SIMILAR APPROPRIATE CONNECTIONS/TRANSITIONS.
<br />DIFFUSER INSTALLATION
<br />SCALE: NONE
<br />FLEXIBLE
<br />CONNECTION
<br />2D MIN.
<br />ROOF CURB
<br />BY DIV. 15
<br />SEE NOTES
<br />1 A2
<br />BACKDRAFT -">
<br />DAMPER
<br />BIRD DUCT
<br />SCREEN DOWN
<br />DISCHARGE
<br />DUCT W/ SCREEN A
<br />SECTION A -A PLAN
<br />NOTES:
<br />1. REFER TO ARCHITECTURAL DRAWINGS FOR INSTALLATION DETAIL. REFER
<br />TO SPECIFICATIONS FOR INSTALLATION.
<br />2. TOP OF DUCT CURB MIN. 12" ABOVE FINISHED SURFACE OF ROOFING OR
<br />BALLAST AS APPICABLE.
<br />3. HEIGHT AS RECOMMENDED BY SMACNA FIG.S-4 FOR ROOF MAINTENANCE,
<br />EXCEPT 36" MAX., MIN, 12- ABOVE FINISHED SURFACE OF ROOFING OR
<br />BALLAST AS APPLICABLE.
<br />ROOF MOUNTED UTILITY SET
<br />(HORIZONTAL DISCHARGE)
<br />FAN SUPPORT CURB
<br />BY DIV. 15
<br />SEE NOTES 1 & 3
<br />SCALE: NONE
<br />fan Installation
<br />stop 1. selecting ;" Location
<br />r ;
<br />�L3cE'SJ,_ _ r . M _.. P:� :,?� f L^,s%;s•:'t,t r�, s.'<f{;t< ,r.fr r,�>�l
<br />E` �.i-:�i3#.aw !'t?sP,t`i�i:. �::, ir33.:f 2Y#.` # f"..,i 'sEf`sS'M, s4;#z'�'�E'•'.>'f. �.%`e�: k., ,{L;' fsEih�.,..�`P:f"2�.-�.i.�:Nl1's�'l'i3 F's3!r;F>':?'r-
<br />fsG� >r Tc3^:�i�f fc�n I Q61,A r; %bauJJ alky- wi). ipnl, : l sery tee. Refer to di. en;swn,4
<br />NOTE Steps' Z 3 way 4e revors l
<br />Step 2. i�s!ie t Nneket
<br />?cEtt3% t£t at :floe
<br />G iX.nr d lcx c3# ofl.
<br />Step 3, Mount FOR
<br />r' n > r
<br />k rk' r n !'t;' hi t r� s. €'ssi;
<br />- t r• r rA r r Ys
<br />.f f � r f. � f
<br />L � .;'E J J" ✓' frty EF ,E k�s..S �� L.r4..r� u s;P
<br />n s
<br />4 4 i Y•
<br />f M s
<br />M� � n
<br />�^ o-o, r i, ti C."
<br />E � ,J` t: �, .� r£ „fi S'st ,� t � ##a,. [i'i ,E.. � $# x ; � t �� ,a fife `�' .�$ �c�;s �B•" E� �
<br />4 .l( t ?<# ! re _'ii3.,t€fl b
<br />d
<br />F lts.DLIgh �C.'pw t'd£lct ,. ? £'.fit mqsiirill, 12 fps «n,# i'cw4 ISii15t ,s:;*C, :.
<br />Step 4. Conn -act In for Pattal CaMe
<br />a,#CE -eft Ff ef;.. Wit" the `.l .Cm r3,ly t�!aµ "# ,a $ prf, it ..n cn :{a:G1 to g E' si i la r; w
<br />NOTE: CONTRACTOR TO INSTALL INDICATOR PANEL IN RESIDENTIAL LAUNDRY ROOM WITH OWNER DIRECTION.
<br />14 DRYER BOOSTER EXHAUST FAN DETAIL
<br />M 1.2.0
<br />\ SCALE: NONE
<br />EXHAUST
<br />FAN
<br />i HOUR RATED
<br />DRYWALL CEILING
<br />,o TOILET EXHA
<br />1.2.0 SCALE: NONE
<br />ATTACH DUCTWORK TO FIRE
<br />DAMPER WITH REINFORCED
<br />ANGLES "S" SLIP
<br />TYP ALL CONNECTI NS
<br />1 )
<br />ACCESS DOOR -� ,
<br />FIREWALL
<br />10 GAUGE WALL SLEEVE
<br />r--- ALL SIDES OF WALL
<br />OPENING
<br />1-xi"xi/8" ANGLE TO SECURE
<br />FIRE DAMPER IN WALL SLEEVE
<br />F-1
<br />FUSIBLE LINK FIRE
<br />DAMPER / RADIATION
<br />oe DAMPER FIRE DAMPER
<br />(SEE SPECS) i "id "xi /8" ANGLE ALL
<br />SIDES TO SECURE WALL
<br />SLEEVE IN OPENING
<br />GRILLE
<br />FLEX CONNECTION
<br />BACKDRAFT DAMPER
<br />EXHAUST FAN
<br />FLEX CONNECTION
<br />NEW EXHAUST DUCT
<br />(VERIFY SIZE A ROUTING IN FIELD)
<br />DISCHARGE CAP WITH
<br />BIRDSCREEN, LOCATE
<br />IS FEET OR MORE FROM
<br />AIR CONDITIONING UNIT
<br />FRESH AIR INLET.
<br />CEILING
<br />1. GYPSUM WALL ASSEMBLY (U.L. CLASSIFIED U300 OR U400 SERIES) (I-HR. FIRE RATING).
<br />2. MAXIMUM 24" x 12" RECTANGULAR STEEL DUCT (MINIMUM 24 GAUGE).
<br />(NOTE: NOT FOR USE IN DUCT SYSTEMS CONTAINING DAMPER).
<br />3. MINIMUM 5/8" DEPTH HILTI CP 601S ELASTOMERIC FIRESTOP SEALANT INSTALLED FLUSH
<br />WITH BOTH SURFACES OF WALL.
<br />4. SEE NOTE No. 3 BELOW.
<br />ROOF
<br />NOTE: 1. MAXIMUM AREA OF OPENING = 325 SQUARE INCHES, WITH MAXIMUM DIMENSION
<br />OF 25 INCHES.
<br />2. ANNULAR SPACE = MINIMUM 1/4", MAXIMUM 3/4".
<br />3. AFTER SEALING ANGLE (1.2 x 2 x i/8") TO DUCT WITH No. 8 (OR LARGER)
<br />STEEL SHEET METAL SCREWS. ANGLE DOES NOT HAVE TO BE FASTENED
<br />SQUARE
<br />TO THE WALL.
<br />„E„ squnfrsP
<br />METAL DUCT (WITHOUT DAMPER)
<br />3 THROUGH 1 HR. GYPSUM WALL 4 PREFABRICATED ROOF CURB
<br />1.2.0 F RATING = 1 HR. UL SYSTEM No. WL7003 M1.2.0 SCALE: NONE
<br />T RATING = 0 HR.
<br />SHEET METAL STRAP SHEET METAL STRAP
<br />1" WIDE OF SAME I'WIDE OF SAME
<br />GAUGE AS DUCT METAL GAUGE AS DUCT
<br />DUCT
<br />SHEET METAL BAND
<br />DUCT 1" WIDE OF SAME METAL
<br />GAUGE AS DUCT
<br />L NEW EXHAUST
<br />REGISTER ANGLE - NOT LESS THAN
<br />1" x 1' x 1/8" SIZED TO MATCH
<br />DUCT
<br />TO EXHAUST FAN DETAIL s SHEET METAL DUCT HANGERS
<br />1.2.0 M 1.2.0
<br />SCALE: NONE SCALE: NONE
<br />3-13€1f" (97 rr£m) Min, kt£ltt K31i 3046S 38-3 (Part 02303'05)
<br />11s
<br />2-11W'(67 mm) MiniFa UM EMbed,
<br />, crsncrete Car caPacreta F£lied cNU
<br />�.
<br />3la-16 x 3" tars 12" (306 exam) Max; centers,
<br />(By �tl`isrs�
<br />`
<br />Backer Rod & Sealant
<br />% 1-114" (38 mm) Max, From corners At Head & Sill,
<br />•
<br />{Eiji Others}-
<br />... Anchor Piave (By others).
<br />i
<br />r l�rz�vld xc# GreerFiaec lti .
<br />$ y 1
<br />s 1
<br />§. J
<br />d^
<br />14" { mm) 1 Structural hick tru tural Angle
<br />(Provided By foenheck 1 ,
<br />d
<br />s G:
<br />_ 11i-' UP>C X 3W' 19 fnm Min.
<br />- �i - - . - - iFIP- ft E'�rtit5
<br />-rF :
<br />$ {
<br />On 12" 3m'45 mMax, centers
<br />4 � 3
<br />4>1s`2'„ (114 satyrs) Max, Fsomr".rr£ser.
<br />$
<br />Fl4Fr It >o ntrF 3 It/
<br />a* HolesPrrpurtctad At Head& Sill,
<br />HPst ltt E SDA03D Louver =�
<br />(Pspvtded 8y Creenherk)
<br /># L*uvef Het ht
<br />9 �
<br />INSTALL ES-30 BACKDRAFT DAMPER
<br />p s"
<br />INSIDE WALL CAVITY WITH LOUVER
<br />s
<br />y
<br />Weided :Suet Structural Support Frame
<br />1.0" (25 nar>a) lw#
<br />INSTALL LOUVERED FACE RETURN
<br />I
<br />GRILLE ON SURFACE OF INTERIOR WALL
<br />1.0" {25 £r ml APachor Plate V.
<br />Setback lief,
<br />CO" (162 mrn)
<br />-------
<br />Rough
<br />E
<br />..
<br />Open lag ,w, "T"
<br />Height
<br />'E e$i4:W; an Elv; pE, w-f ; at ki}mmng mead and r0l using spt: ;tfed an •hats'' nin
<br />'<
<br />r „ x �tr
<br /><ft ssn - � 2 rn i n s � $^'f sfe ft.n v r#!i amf . r� Eta; -�f s
<br />mt c .�s � e.
<br />tl �
<br />u
<br />Xld 120
<br />x'
<br />i
<br />- ry 1.h10,625 E
<br />ftkD >s 'Art, t>tF?t `'t ek 3�#cr_? .1!P3•-Ic k n rnir i + urn. E43 {gfh ASTM R':.f S F £t.
<br />3:..........,............................,,,...._..,ts......,._..._...,....,.i
<br />:i'2 '7oo,19.i-no �i`f)ncro o, q Masonry: ?)+aP f'#slit li 1 E`i }7? �^e 7:'i„ 3 .r #%s X 3 is
<br />It rr+'O l > 48. #I'r:;n R � f OPI - i t 5
<br />',part rf#i£� 4 F#5„ 2.25 in mil i#nntr14 ErnP3Qr#.. � � -S tft ff $murf.+, odge
<br />F ,
<br /># # � PT n a f f.s32' f t ram, c mar angle iti 1 iv 2 fs car Y n „�$<t v w. £ a ,.us t,
<br />lk C flr3�' - s'{ � Q
<br />Er `i E"l <= M'[s.. ?(sf n #'t = s`iiiF-; "S..,t
<br />rr E'!" ry .vii9 ✓t? 1.11, l%##F7 , head - the ?"oaAt urt,., foe
<br />3, SeM �iftiY eF oper.i g to peednl'E~tev, k;:"f+i,� backer f'c l'l and scawfv sIby C3flers�,
<br />"3l? } �, rtisE CEmerfs':c:Es :fiOkr<n urc .tt c:nct� c# s?1c*iG�
<br />+,ISmb Detail
<br />:r �y
<br />UST FAN DETAIL 1 1 /2" HR. FIRE DAMPER IN WALL 12 CORRIDOR LOUVER INSTALLATION DETAIL
<br />M1.2.0 SCALE: NONE M1.2.0
<br />SCALE: NONE
<br />A.�,,�7.5 AKE #`F�? +dl ENSING._ NIT BASE <��t:� � �� �� 1�s���: �
<br />Xf 8#
<br />L� STAND H
<br />_.
<br />kf+ -a- P,es+sstr
<br />f
<br />i��` aU�----- �' dF s > ¢ r � it 0 Rg'
<br /><
<br />t
<br />< ; •., Y. ,.� r s c s 7 trod .mtEe>�c^lirm 1uVA wo commeite
<br />41
<br />.....`.
<br />•
<br />i �. � :.1 �k'12 tt1 .^. �� f > r: is r £n• £ • >'.
<br />4�ifa',na rC T r4YsF f, 7ifrill.!]R i�'.irifs!'
<br />64 ey �,x iy :A' .:rL4iM _..
<br />t
<br />tt IWI.'4.%;
<br />s"`47t'6:
<br />„t'i87;ws >'f1F.9j>,i�C V
<br />8K'�SX{r`•G
<br />6,4>1'FF".RiAI 6z 1:4LSW
<br />xOF,tst^
<br />4 Yif?•
<br />i4E »p s
<br />qw-,=-..
<br />t>f>dY?:'lYy
<br />+�hSY P34'#5f
<br />S
<br />.i/J)iY
<br />:
<br />r
<br />..
<br />r
<br />�
<br />r "..
<br />E:
<br />....._...
<br />f
<br />` z ¢art fr�zrsk rfS(i: `i i ls'caxs tstaa A[* f%i txi:es= s:tgcsxe rt PA ). Ji,*4s4i =14c4; u4wAo,.4ssura
<br />L {
<br />xz'Ft:ld Hirai .c..aasa fm l..A�tattd o�sLctars: as fat. den�sca.34Sussnnaf{�. eskcuz ssai�cE;.r�
<br />E#
<br />w t.
<br />:Si�tiLF+f�£SS59 d}�i5t4.t•_dttitiat�� .53. YA�.i!XCiIlM. }$DCS • r#J���6fC
<br />iF ii 'r
<br />i+8tg.:ll:t�rT�3R
<br />1. ,
<br />:'fI' �@%iC SHii#Y1S,35fi5 YSt2 Ef,-3S.'C b5 ,`,,KJ J�}#kI T'IG%liF�iS�.i£ki[ 4.iSIT, iYISI A.�.r:?:�F.
<br />{..
<br />#F i+ :SS r{ fSt$.i. ' !fP Ta•'fL :1L9:?j##q .'>Y.ti4.i<I,kf f[s -. ..�F, osE i;%5: iuWF50.'-�D1�:Y59,Yt /.s; 3.i9'. iS i<5
<br />t
<br />?• na.+n >w:+�,�sst �.w.z3;rYratt lead+ # zh- #+>hxe;Lr cd rir £:a,: p';ttca: ivtxzz h: anssg-�+ z exmis�tc aver£ .sex.#
<br />� ;
<br />.:,f,.(.:
<br />xuucsaccx
<br />-
<br />.
<br />s•
<br />' "
<br />.�
<br />8 a+ui!sss EsuTu t urssor ,�S+TJ sieve a xcsawa.s is i'W $" x sainv ssn ..]]-� �s�essrx ul Y" kr
<br />. i
<br />Y
<br />rvn> ,tk,. ;wl,z # $5eF'4.,I5A � :. fetY.4+aT,d 6- ! v .'k{t," %Gri:0r aCfi.r •5 "ib ff:a4 i., t'+:LK t q-'2i'u'4> h3 za�ld>fl,{ 4RF:•
<br />r, .Yif. 1
<br />....
<br />Fttars• cr 4ce +"efrzt L„ it. SJ€". weds: ;ain+ #: i#�fs:r,{d»s� 3i' sns.Eit , n iF¢ stdf zvu#sas 3r 3a,.
<br />r r,aas � c
<br />:
<br />;sn3s°;xti�lsL.t+u's}i. s#u: rx+a##. #a;etgtta sx r#.r.+ ru}"z?t� iawa�. "Etinrasstknss;n sum a2#vw'txk-frn 77b: etirnss i4tsad arr.
<br />''7�" #
<br />3
<br />SHEET METAL
<br />SAFING OR ANGLES.
<br />ANGLES REQUIRED
<br />WHEN SAFING USED
<br />FOR DUCT SUPPORT
<br />AT FLOORS.
<br />DUCT LINING WHERE
<br />SHOWN ON PLANS OR
<br />SPECIFIED
<br />1 r
<br />PACK SPACE WITH I NOTE:
<br />FIBROUS MATERIAL WHERE FIRE, SMOKE, OR COMBINATION
<br />AND SEAL BOTH FIRE/SMOKE DAMPERS ARE REQUIRED,
<br />SIDES. SEE SPECS INSTALLATION WILL BE PER DAMPER
<br />FOR MATERIALS. MANUFACTURER'S REQUIREMENTS
<br />TYPICAL INTERIOR WALL OR
<br />9 FLOOR SLAB PENETRATION
<br />1.2.0
<br />SCALE: NONE
<br />ROOF TOP CONDENSER SUPPORT INSTALLATION GUIDE
<br />SCALE: NONE
<br />- -P CURB
<br />pry ��3�1
<br />At
<br />FREDERICK MUSCATELLO, PE
<br />FL. PE # 62451
<br />PO Box 941168
<br />MAITLAND, FL 32794-1168
<br />EMAIL: fredOfcmengineering.com '
<br />v
<br />t
<br />U
<br />N
<br />Z
<br />0
<br />>Ln
<br />CV
<br />F'
<br />�
<br />O
<br />F
<br />U
<br />E~
<br />r�
<br />g4
<br />P
<br />z
<br />o
<br />O
<br />O
<br />•a
<br />U
<br />N
<br />a�
<br />v
<br />Q
<br />�
<br />�
<br />A
<br />�
<br />COO
<br />A
<br />W
<br />w
<br />6
<br />N
<br />r�
<br />C
<br />a�
<br />%
<br />CL
<br />CF
<br />t\ 1
<br />J
<br />S` �y
<br />U
<br />U
<br />][
<br />U
<br />..
<br />it
<br />o
<br />J
<br />Q
<br />W
<br />�
<br />�
<br />project no.
<br />drawn by:
<br />2006-068.00
<br />date:
<br />checked by:
<br />NOV 2006
<br />scale:
<br />approved by:
<br />sheet no.
<br />M 1.2.E
<br />r
<br />N
<br />N
<br />0
<br />U
<br />(M
<br />C
<br />0
<br />U
<br />
|