|
I I !!-♦ nl! If, II?WrrnIEyI11110• 1111 I _I_ I_
<br />4
<br />0
<br />0
<br />a�
<br />0
<br />O
<br />c�
<br />0
<br />0)
<br />0
<br />N
<br />0
<br />O
<br />1,
<br />O N
<br />0
<br />4-
<br />a)
<br />c
<br />0
<br />t
<br />U
<br />0
<br />0
<br />a)
<br />c
<br />0
<br />it
<br />U
<br />C
<br />0
<br />o
<br />L
<br />a�
<br />0
<br />ME
<br />z
<br />0
<br />0
<br />�00
<br />U
<br />c
<br />s
<br />s �
<br />c 0
<br />0
<br />1. GENERAL
<br />A. PROVIDE ALL LABOR, MATERIALS, AND EQUIPMENT REQUIRED FOR A COMPLETE SYSTEM AS OUTLINED IN
<br />THE CONTRACT DRAWINGS AND THESE SPECIFICATIONS.
<br />B. NOTE THAT DRAWINGS ARE DIAGRAMMATIC ONLY AND INTENDED TO SHOW THE GENERAL ARRANGEMENT
<br />OF SYSTEMS, NOT EVERY MINUTE DETAIL.
<br />C. DO NOT SCALE PLANS.
<br />D. PROVIDE ALL NECESSARY FITTINGS, BOXES, TRANSITIONS, CONNECTORS, ETC. WHETHER SHOWN OR NOT
<br />ON PLANS.
<br />E. ALL WORK IS NEW UNLESS OTHERWISE NOTED.
<br />R THESE PLANS REPRESENT THE DESIGN INTENT BASED ON INFORMATION AVAILABLE AT THE TIME OF
<br />DESIGN. ANY SUBSTANTIAL MODIFICATIONS OR ALTERATIONS MADE DURING THE CONSTRUCTION PHASE
<br />SHALL BE REPORTED TO THE ENGINEER PRIOR TO WORK. MODIFICATIONS MADE WITHOUT THE ENGINEER'S
<br />WRITTEN APPROVAL SHALL REMAIN THE RESPONSIBILITY OF THE CONTRACTOR.
<br />G. IN CASE OF ANY DISCREPANCIES BETWEEN THE DRAWINGS, SPECIFICATIONS, FIELD CONDITIONS, CODES,
<br />ETC. IT IS THE RESPONSIBILITY OF THE CONTRACTOR TO REFER ALL SUCH MATTERS TO THE ENGINEER IN
<br />WRITING IMMEDIATELY FOR RESOLUTION PRIOR TO EXECUTING ANY WORK. ANY WORK PERFORMED WITHOUT
<br />THE WRITTEN AUTHORIZATION OF THE ENGINEER SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR.
<br />H. ALL WORK SHALL CONFORM TO THE FOLLOWING CODES CAS APPLICABLE) AS WELL AS ALL LOCAL
<br />REGULATIONS, ORDINANCES, AND AMENDMENTS
<br />2011 FLORIDA BUILDING CODE �TI4 EDITION
<br />2014 NFPA-70 NATIONAL ELECTRICAL CODE
<br />2017 FLORIDA BUILDING CODE FIRE CODE
<br />2, SCOPE OF WORK
<br />PROVIDE NEW ELECTRICAL DEVICES AND CONNECT TO EXISTING SYSTEM. PROVIDE NEW LIGHTING,
<br />RECEPTACLES, SWITCHES, ETC. AND CONNECT AS SHOWN ON PLANS,
<br />3. ITEMS FURNISHED BY CONTRACTOR
<br />IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO PROVIDE ALL MATERIALS, EQUIPMENT, AND
<br />ACCESSORIES NECESSARY TO MAKE A COMPLETE INSTALLATION. ALL EQUIPMENT SHALL BE STORED IN A
<br />SAFE, DRY PLACE IN THE MANUFACTURER'S ORIGINAL PACKAGING UNTIL READY FOR USE. THE OWNER SHALL
<br />NOT BE RESPONSIBLE FOR PROVIDING ANY PART OF THE PROJECT, UNLESS SPECIFICALLY NOTED. THE
<br />CONTRACTOR SHALL ALSO BE RESPONSIBLE FOR PAYING ALL REQUIRED FEES, OBTAINING ALL PERMITS,
<br />AND ARRANGING FOR ALL INSPECTIONS, INCLUDING COORDINATION WITH AND SATISFYING ALL
<br />REQUIREMENTS OF THE ELECTRICAL UTILITY GOMP,4NY(IE5) AS MAY BE REQUIRED TO EXECUTE THIS SCOPE
<br />OF WORK.
<br />4. WORK IN EXISTING BUILDINGS
<br />A. DO NOT USE POWDER DRIVEN FASTENERS OF ANY TYPE.
<br />B. ALL ITEMS REMOVED AND NOT RE -USED SHALL BE TURNED OVER TO THE OWNER. CONTRACTOR SHALL
<br />REMOVE ANY UNSATISFACTORY ITEMS FROM THE PROJECT SITE.
<br />C. SOME EXISTING ITEMS TO REMAIN WITHOUT WORK ARE SHOWN FOR CLARITY OR REFERENCE ONLY. NOTE
<br />THAT ADDITIONAL ITEMS WITHOUT WORK MAY ALSO BE PRESENT.
<br />D. DRAWINGS OF EXISTING SYSTEMS ARE BASED ON EXISTING DOCUMENTS AND FIELD CONDITIONS, SOME OF
<br />WHICH MAY BE UNVERIFIED. PRIOR TO SUBMITTING A BID, GONTRACTOR SHALL STUDY THE PLANS AND VISIT
<br />THE PROJECT SITE IN ORDER TO BECOME FAMILIAR WITH EXISTING CONDITIONS. ANY DISCREPANCIES IN THE
<br />GONTRACT DOCUMENTS WHICH COULD SIGNIFICANTLY IMPACT THE PROJECT BUDGET OR SGHEDULE MUST BE
<br />REPORTED TO THE ENGINEER IN WRITING IMMEDIATELY. FAILURE TO DO SO WILL NOT BE SUFFIGIENT CAUSE
<br />FOR DELAYS OR CHANGES LATER IN THE PROJECT. CHANGE ORDERS RESULTING FROM FAILURE TO
<br />PROPERLY INVESTIGATE EXISTING FIELD CONDITIONS WILL NOT BE ACCEPTED. ALL WORK 15 NEW UNLESS
<br />OTHERWISE NOTED.
<br />E. MODIFICATIONS TO EXISTING SYSTEMS NECESSARY TO CONNECT TO NEW WORK SHALL BE CONSIDERED
<br />TO BE PART OF THE BASIC WORK OF THIS CONTRACT.
<br />F. COORDINATE ALL WORK SCHEDULES WITH THE OWNER TO MINIMIZE DISRUPTIONS TO EXISTING SYSTEMS
<br />OUTSIDE THIS SCOPE OF WORK.
<br />5, COORDINATION
<br />ALL WORK ON THIS PROJECT SHALL BE COORDINATED WITH THE OWNER AND ALL OTHER TRADES PRIOR
<br />TO BEGINNING AY WORK OR ORDERING ANY MATERIALS. CONTRACTOR SHALL REVIEW PLANS OF ALL
<br />DISCIPLINES INVOLVED AND ADVISE THE ARCHITECT IN WRITING OF ANY GONFLICTS, CODE OR SAFETY
<br />ISSUES THAT MAY EXIST PRIOR TO ANY FABRICATION OR ORDERING OF EQUIPMENT. RESOLUTION OF SUCH
<br />CONFLICTS WHICH ARE NOT REPORTED PRIOR TO CONSTRUCTION SHALL REMAIN THE RESPONSIBILITY OF
<br />THE CONTRACTOR AND CHANGE ORDER PROPOSALS FOR SUCH WORK WILL NOT BE ACCEPTED. PROVIDE
<br />ROUTING AND OFFSETS NECESSARY TO AVOID GONFLICTS WITH STRUCTURE, FINISHES, AND WORK OF OTHERS
<br />CONTRACTOR SHALL PROVIDE ALL CORE PENETRATIONS AND PATCHING FOR FLOOR PENETRATIONS.
<br />(o. DEVICE LOG,4TIONS
<br />A. INSTALL ALL DEVICES IN ACCESSIBLE LOCATIONS, EXCEPT AS SPECIFIGALLY NOTED OR PROHIBITED
<br />BY NEC.
<br />B. PROVIDE MIN, 113x18 INCH PAINTED ALUMINUM ACCESS DOORS WITH FULL HINGE AND KEY, FOR ACCESS TO
<br />ALL ELECTRICAL DEVICES, PULL BOXES, JUNCTION BOXES, AND ACCESSORIES IN PLASTER, DRYWALL, OR
<br />INACCESSIBLE CEILINGS, OR IN WALLS. GROUP DEVICES AT A SINGLE LOCATION, AS AVAILABLE.
<br />C. ACCESS DOORS IN RATED WALLS OR CEILINGS SHALL HAVE A RATING AT LEAST EQUAL TO THE RATING
<br />OF THE WALL OR CEILING.
<br />D. ALL DEVICES, RACEWAYS, ETC. WHICH ARE EXPOSED SHALL BE PAINTED TO MATCH THE ADJACENT
<br />SURFACE OR AS DIRECTED BY THE ARCHITECT.
<br />E. ALL ELECTRICAL EQUIPMENT SHALL BE INSTALLED A MINIMUM OF 1'-0" ABOVE THE BASE FLOOD
<br />ELEVATION.
<br />7. EQUIPMENT GENERAL
<br />ALL EQUIPMENT OF EACH TYPE SHALL BE BY ONE MANUFACTURER AND SHALL HAVE CHARACTERISTIGS AS
<br />LISTED IN THE EQUIPMENT SGHEDULES. ALL EQUIPMENT SHALL BE UL LISTED, NO EXCEPTIONS 1
<br />SUBSTITUTIONS ARE ACCEPTABLE PROVIDED THAT THE SUBSTITUTED EQUIPMENT HAS EQUIVALENT
<br />CHARACTERISTIGS AS THAT SCHEDULED AND IS PROVIDED BY AN ACCEPTABLE MANUFACTURER AS LISTED
<br />FOR THAT EQUIPMENT TYPE. CONTRACTOR SHALL SUBMIT PRODUCT DATA FOR ALL EQUIPMENT TO THE
<br />ENGINEER FOR APPROVAL PRIOR TO ORDERING. SUBMITTALS SHALL INCLUDE DIMENSIONS, WEIGHT,
<br />VOLTAGE, AMPERAGE, HORSEPOWER, POWER FACTOR, INTERRUPTING CAPACITY, ETC.
<br />8. GONDUCTORS
<br />A. PROVIDE ONLY DUAL RATED THWN-2/THHN-2 COPPER GONDUCTORS. MINIMUM SIZE IS NUMBER 12 AWG.
<br />B. CONDUCTORS SHALL HAVE COLORED INSULATION FOR IDENTIFICATION PURPOSES AS FOLLOWS:
<br />240/2015/120V 480/277V
<br />PHASE A BLAGK PHASE A BROWN
<br />PHASE B RED PHASE B ORANGE
<br />PHASE C BLUE PHASE C YELLOW
<br />NEUTRAL WHITE NEUTRAL GRAY
<br />GROUND GREEN GROUND GREEN
<br />C. GROUNDED GONDUCTORS WHICH CARRY OVER 250V TO GROUND SHALL BE TAGGED WITH VOLTAGE AT
<br />EACH TERMINATION POINT.
<br />D. DO NOT INSTALL MORE THAN THREE CURRENT CARRYING CONDUCTORS IN SINGLE RACEWAY (NOT
<br />INCLUDING NEUTRAL) WHICH WILL REQUIRE NEC TABLE 310-1io NOTE 0 DERATING.
<br />E. PHASE AND GROUNDING CONDUCTOR SIZES SHALL BE INCREASED AS NECESSARY TO ACGOUNT FOR
<br />VOLTAGE DROP.
<br />9. RACEWAYS
<br />A. INSTALL ALL WIRING ABOVE GROUND IN METALLIC CONDUIT (EMT INDOORS, RGS OUTDOORS OR IN
<br />EXPOSED LOG,4TION5).
<br />B. ALL EXPOSED RACEWAYS SHALL BE RUN PARALLEL TO WALLS OR CEILINGS AND SHALL BE PAINTED TO
<br />MATCH ADJACENT SURFACES OR AS DIRECTED BY THE OWNER,
<br />C. WHERE MULTIPLE RACEWAYS ARE RUN EXPOSED, RUN ALL RACEWAYS SQUARE AND PARALLEL IN A NEAT
<br />AND ORDERLY MANNER.
<br />D. MAKE FINAL GONNECTIONS (NOT MORE THAN (o'-O" LONG) TO ALL EQUIPMENT WITH FLEXIBLE METALLIC
<br />CONDUIT (DRY LOCATIONS) OR LIQUID TIGHT FLEXIBLE METALLIC CONDUIT (DAMP OR WET LOCATIONS).
<br />E. INSTALL ALL WIRING BELOW GROUND IN RIGID NON-METALLIG GONDUIT (SGHEDULE 40 PVC). ALL
<br />EXTERIOR NONMETALLIC CONDUITS SHALL BE UV RESISTANT. ALL CONDUITS RUN BELOW GROUND SHALL BE
<br />INSTALLED ACCORDING TO NEC300-5.
<br />F. TYPE MC CABLE MAY BE USED AS AN ALTERNATIVE TO CONDUCTORS IN METAL RACEWAY IN DRY
<br />INDOOR LOCATIONS, PROVIDED IT IS INSTALLED PER NEC AND APPROVED BY THE AUTHORITY HAVING
<br />JURISDICTION.
<br />G. METALLIC CONDUITS SHALL NOT BE USED AS GROUNDING CONDUCTORS. PROVIDE A SEPARATE
<br />GROUNDING CONDUCTOR IN ALL METALLIC CONDUITS, BONDED AT BOTH ENDS PER NEC.
<br />1 ELECTRICAL SPECIFICATIONS
<br />SCALE NONE
<br />10. GROUND ING
<br />A. ALL ELEGTRICAL SYSTEMS SHALL BE PROPERLY GROUNDED PER NEC 250.
<br />B. EXPOSED GROUNDING ELECTRODE GONDUCTORS SHALL BE PROTECTED BY RIGID
<br />NONMETALLIC CONDUITS, MIN SIZE = 4"
<br />C. PROVIDE GROUNDING ELECTRODE GONDUCTORS TO DRIVEN GROUND RODS AT THE BASE
<br />OF ALL LIGHT POLES, REMOTE BUILDINGS, OR REMOTE EQUIPMENT.
<br />D. ALL METAL ITEMS OF THE ELECTRICAL SYSTEM INCLUDING RACEWAYS, BOXES, FIXTURES,
<br />ETC. SHALL BE BONDED AND PROPERLY GROUNDED.
<br />11. SWITCHBOARDS AND PANEL BOARDS
<br />A. PROVIDE 5WITCHB0ARD5 AND PANEL BOARDS, SIZE AND ARRANGEMENT AS INDICATED
<br />ON PLANS AND SCHEDULES.
<br />B. MOUNT PANEL BOARDS NOT MORE THAN 40" A.F.F. TO CENTER.
<br />C. ENCLOSURES SHALL BE SUITABLE FOR THE ENVIRONMENT IN WHICH THEY ARE INSTALLED
<br />(NEMA I INDOORS, NEMA 3R OUTDOORS, ETC;.)D. PROVIDE A TYPEWRITTEN PANEL SCHEDULE IDENTIFYING THE FUNCTION OF ALL CIRCUIT
<br />BREAKERS IN A CLEAR PLASTIC SLEEVE PERMANENTLY ATTACHED TO THE PANEL BOARD
<br />COVER.
<br />E. ALL SWITCHBOARDS AND PANEL BOARDS SHALL HAVE A THERMOPLASTIC IDENTIFYING
<br />NAMEPLATE PERMANENTLY AFFIXED TO THE FRONT OR COVER.
<br />F. PROVIDE ONE 1" EMPTY GONDUIT FROM PANEL TO (" ABOVE CEILING FOR EVERY (3)
<br />SPARES OR SPACES.
<br />G. PANEL BOARDS AND SWITCHBOARDS BY: SQUARE D, CUTLER HAMMER, OR GE.
<br />12. CIRGUIT BREAKERS
<br />A. ALL CIRCUIT BREAKERS SHALL BE BY A SINGLE MANUFACTURER, WITH SAME STYLE AND
<br />WITHSTAND RATING TO MATCH THE PANEL IN WHICH THEY ARE INSTALLED.
<br />B. PROVIDE MULTIPLE POLE CIRGUIT BREAKERS FOR MULTIPLE POLE CIRCUITS. HANDLE TIES
<br />ARE NOT PERMITTED.
<br />C. PROVIDE HACK TYPE CIRCUIT BREAKERS FOR ALL HVAC EQUIPMENT AND WATER
<br />HEATERS.
<br />D. PROVIDE GROUND FAULT CIRGUIT INTERRUPTER BREAKERS FOR ALL OUTDOOR,
<br />BATHROOM, AND KITCHEN BRANCH CIRCUITS WHICH DO NOT UTILIZE GFCI RECEPTACLES, OR
<br />AS OTHERWISE REQUIRED BY THE AUTHORITY HAVING JURISDICTION,
<br />E. NOT USED.
<br />F. NOT USED,
<br />G. PROVIDE INVERSE TIME CIRCUIT BREAKERS FOR MOTORS UNLESS SPECIFIED OTHERWISE,
<br />H. CIRCUIT BREAKERS SHALL BE PROVIDED WITH INDICATING ON/OFF HANDLES.
<br />J. GIRGUIT BREAKERS FOR FIRE ALARMS SHALL BE LOCKABLE.
<br />K. CIRCUIT BREAKERS BY: SQUARE D, CUTLER HAMMER, OR GE.
<br />13. DEVICES
<br />A. PROVIDE GALVANIZED STEEL BOXES FOR ALL DEVICES IN EXPOSED LOCATIONS OR
<br />REGESSED INTO RATED WALLS.
<br />B. PROVIDE THERMOPLASTIC OR GALVANIZED STEEL BOXES FOR ALL DEVICES TO BE
<br />RECESSED INTO NON -RATED WALLS.
<br />C. FINISH OF ALL DEVICES AND COVER PLATES SHALL BE AS DIRECTED BY THE OWNER IN
<br />WRITING PRIOR TO ORDERING.
<br />D. ALL RECEPTACLES SHALL BE OF THE GROUNDING TYPE.
<br />E. ALL REGEPTACLES SHALL BE 20 AMP, 120 VOLT RATED, GOMMERCIAL GRADE.
<br />F. PROVIDE DISCONNECT SWITGHES (WITH OR WITHOUT FUSES AS SPECIFIED) IN ENCLOSURES
<br />SUITABLE FOR THE ENVIRONMENT IN WHICH THEY ARE INSTALLED (NEMA 1 INDOORS, NEMA 3R
<br />OUTDOORS s AT WATER HEATER, ETC.)
<br />G. ALL SWITCHES AND RECEPTAGLES BY LEVITON, GE, OR EQUIVALENT.
<br />H. PROVIDE GFCI RECEPTAGLES IN ALL KITGHENS, BATHROOMS, GARAGES, OUTSIDE, OR
<br />WHEREVER ELSE SHOWN ON DRAWINGS. LABEL ALL DEVICES DOWNSTREAM OF GFCI DEVICE
<br />AS "GFCI PROTECTED". PROVIDE AT LEAST ONE DUPLEX GFCI PROTECTED RECEPTACLE IN A
<br />WEATHERPROOF ENCLOSURE WITHIN TWENTY FIVE (25) FEET OF ALL ROOF OR GRADE MOUNTED
<br />EXTERIOR HVAC EQUIPMENT.
<br />J. FOR GFCI REGEPTACLES NOT ON A DEDICATED BRANCH CIRCUIT (SUCH AS OUTDOOR
<br />RECEPTACLES CONNECTED TO THE NEAREST INTERIOR CIRGUIT), MAKE EVERY ATTEMPT TO
<br />LOCATE THE GFCI RECEPTACLE AT THE END OF THE CIRCUIT RUN SO AS TO MINIMIZE THE
<br />POSSIBILITY OF CAUSING NUISANCE POWER LOSS TO OTHER DEVICES WHEN THE GFCI DEVICE
<br />TRIPS.
<br />14, LIGHTING
<br />A. ALL LIGHT FIXTURES SHALL BE THOSE DESCRIBED IN THE LIGHTING FIXTURE SGHEDULE OR
<br />THEIR EQUIVALENT AS APPROVED BY THE ENGINEER PRIOR TO ORDERING. IF ALTERNATE
<br />FIXTURES ARE USED, IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO
<br />COORDINATE THEIR INSTALLATION DETAILS WITH ALL OTHER TRADES WITH REGARD TO
<br />SPACE REQUIRED, WIRING, POWER CONSUMPTION, ETC-
<br />B. LIGHTING BRANCH CIRCUITS SHALL NOT BE LOADED TO MORE THAN 50% OF THE CIRCUIT
<br />BREAKER AMPACIT`I'.
<br />C. ALL LIGHT FIXTURES INSTALLED IN DAMP, WET, OR HAZARDOUS (CLASSIFIED) LOCATIONS
<br />SHALL BE LISTED FOR SUCH USE.
<br />D. INGANDESGENT LAMPS SHALL NOT BE USED EXCEPT FOR DIMMING PURPOSES OR AS
<br />OTHERWISE STATED ON PLANS OR PERMITTED BY THE AUTHORITY HAVING JURISDICTION.
<br />E. ALL FLUORESCENT OR HID LIGHT FIXTURES SHALL BE FUSED WITH ELECTRONIC BALLAST
<br />AS REQUIRED TO MEET THE SWITCHING REQUIREMENTS DESCRIBED ELSEWHERE IN THESE
<br />DOCUMENTS OR THE AUTHORITY HAVING JURISDICTION. PROVIDE MULTIPLE BALLASTS WHERE
<br />REQUIRED TO PROVIDE MULTIPLE LIGHTING LEVELS TO COMPLY WITH APPLICABLE ENERGY
<br />CODES.
<br />F. INTERIOR LIGHTING IN ALL BUILDINGS LARGER THAN 5,000 SQUARE FEET SHALL BE
<br />PROVIDED WITH AUTOMATIC CONTROLS. CONTROLS SHALL CONSIST OF A CENTRAL
<br />TIME -OF -DAY SCHEDULING CONTROLLER OR OCCUPANG'�' SENSORS LOCATED IN EACH
<br />SPACE. OCCUPANCY SENSORS SHALL BE LOCATED SO THE OCCUPANT CAN SEE THE
<br />CONTROLLED LIGHTING AND SHALL BE CAPABLE OF A 4 HOUR OVERRIDE. LIGHTING
<br />CONTROL ZONES SHALL NOT EXCEED 2,500 SQUARE FEET.
<br />G. PROVIDE TIME CLOCKS OR NORTH FACING PHOTOCELLS TO CONTROL ALL EXTERIOR
<br />LIGHTING CIRCUITS AUTOMATICALLY. PROVIDE LIGHTING CONTACTORS AS REQUIRED.
<br />H. ALL EXIT SIGNS AND EMERGENCY EGRESS LIGHTING SHALL NOT BE SWITCHED AND SHALL
<br />HAVE BATTERY BACKUP OR BE GONNECTED TO THE EMERGENCY POWER SYSTEM.
<br />15. WARRANTIES AND MAINTENANCE
<br />A. ALL EQUIPMENT SHALL BE STARTED, TESTED, ADJUSTED, LUBRICATED, CLEANED, AND
<br />PLACED IN GOOD OPERATING CONDITION BY THE CONTRACTOR. CONTRACTOR SHALL
<br />GUARANTEE ALL EQUIPMENT, MATERIALS, AND WORKMANSHIP TO BE FREE OF DEFECTS FOR A
<br />PERIOD OF ONE YEAR FROM THE DATE OF ACCEPTANCE BY THE OWNER AND THE
<br />CONTRACTOR SHALL REPAIR ANY SUCH DEFECTS AT NO COST TO THE OWNER. ALL
<br />EQUIPMENT INCLUDED IN THE PROJECT SHALL BE COVERED BY THE MANUFACTURER'S
<br />WARRANTY FOR THE DURATION OF THAT WARRANTY. GOPIES OF ALL MANUFACTURER'S
<br />WARRANTIES AND CONTRACTOR WARRANTIES SHALL BE PROVIDED TO THE OWNER AT FINAL
<br />ACCEPTANCE.
<br />B. GONTRACTOR SHALL MEET WITH THE OWNER'S REPRESENTATIVE AND REVIEW ALL
<br />OPERATIONS AND MAINTENANCE OF ALL SYSTEMS. CONTRACTOR SHALL PROVIDE THE OWNER
<br />WITH BOUND COPIES OF ALL OPERATION AND MAINTENANCE MANUALS INCLUDING PARTS
<br />LISTS, MAINTENANCE SGHEDULES, ETC.
<br />C. THE GONTRACTOR SHALL CONTINUALLY RECORD ANY AND ALL DEVIATIONS TO THE
<br />CONTRACT DOCUMENTS MADE DURING CONSTRUCTION AND PROVIDE A COMPLETE SET OF
<br />THESE RECORD DRAWINGS TO THE OWNER WITHIN 30 DAYS OF COMPLETION OF
<br />CONSTRUCTION. IF REQUIRED BY THE AUTHORITY HAVING JURISDICTION, IT SHALL BE THE
<br />RESPONSIBILITY OF THE GONTRACTOR TO SECURE THE SERVICES OF A LICENSED
<br />PROFESSIONAL ENGINEER TO PROVIDE SIGNED AND SEALED RECORD DRAWINGS.
<br />1(o. TESTING
<br />A. AT THE COMPLETION OF THE PROJECT, TEST ALL ELECTRICAL EQUIPMENT AND DEVICES
<br />FOR PROPER OPERATION. TEST FOR GROUNDS AND SNORTS. REPORT ALL RESULTS TO THE
<br />ARCHITECT IN WRITING. REPLACE ANY DEFECTIVE DEVICES OR EQUIPMENT.
<br />B. TEST ALL FIRE ALARMS, GENERATORS, AND OTHER LIFE SAFETY EQUIPMENT IN THE
<br />PRESENGE OF THE ENGINEER AND THE FIRE OFFICIAL TO DEMONSTRATE OPERATION. MAKE
<br />ANY MODIFICATIONS NECESSARY AS REQUIRED BY THE FIRE OFFICIAL AND REPAIR OR
<br />REPLACE ANY DEFECTIVE ITEMS AS NECESSARY.
<br />LEGEND
<br />SYMBOL
<br />DESCRIPTION
<br />MOUNTING/COMMENTS
<br />0
<br />FLUORESCENT LIGHT FIXTURE
<br />SEE LIGHT FIXTURE SCHEDULE
<br />o--1
<br />FLUORESCENT STRIP FIXTURE
<br />SEE LIGHT FIXTURE SCHEDULE
<br />FLUORESCENT LAY -IN FIXTURE
<br />SEE LIGHT FIXTURE SCHEDULE
<br />FLUORESCENT LAY -IN FIXTURE
<br />SEE LIGHT FIXTURE SCHEDULE
<br />EXIT LIGHT, SINGLE OR DOUBLE FACE,
<br />®
<br />SEE LIGHT FIXTURE SCHEDULE
<br />BATTERY BACK UP
<br />EMERGENCY LIGHT
<br />SEE LIGHT FIXTURE SCHEDULE
<br />BATTERY BACK UP
<br />INCANDESCENT, HID OR FLUORESCENT
<br />SEE LIGHT FIXTURE SCHEDULE
<br />WALL MOUNTED FIXTURE
<br />h
<br />INCANDESCENT, HID OR FLUORESCENT
<br />Y
<br />CEILING MOUNTED FIXTURE
<br />SEE LIGHT FIXTURE SCHEDULE
<br />0
<br />INCANDESCENT, HID OR FLUORESCENT
<br />SEE
<br />RECESSED FIXTURE
<br />LIGHT FIXTURE SCHEDULE
<br />PANELBOARD
<br />SEE PANEL SCHEDULE
<br />120/208V, 3PH
<br />PANELBOARD
<br />SEE PANEL SCHEDULE
<br />271/48OV, 3PH
<br />DISCONNECT SWITCH
<br />SEE PLANS FOR SIZE, TYPE
<br />AND VOLTAGE
<br />SINGLE POLE SWITCH
<br />44" TO CENTER ABOVE FINISHED
<br />120/271V, 20A
<br />FLOOR UNLESS OTHERWISE NOTED
<br />S3
<br />THREE WAY SWITCH
<br />44" TO CENTER ABOVE FINISHED
<br />120/2-1-IV, 20A
<br />FLOOR UNLESS OTHERWISE NOTED
<br />54
<br />FOUR WAY SWITCH
<br />44" TO CENTER ABOVE FINISHED
<br />120/2-1-IV, 20A
<br />FLOOR UNLESS OTHERWISE NOTED
<br />SQL
<br />SINGLE POLE SWITCH WITH PILOT LIGHT
<br />44" TO CENTER ABOVE FINISHED
<br />120/271V, 20A
<br />FLOOR UNLESS OTHERWISE NOTED
<br />SM
<br />SINGLE POLE MOTOR RATED SWITCH
<br />44" TO CENTER ABOVE FINISHED
<br />120/277V, 204
<br />FLOOR UNLESS OTHERWISE NOTED
<br />SD
<br />SINGLE POLE DIMMER SWITCH
<br />4411 TO CENTER ABOVE FINISHED
<br />12OV, 20A, VERIFY WATTAGE
<br />FLOOR UNLESS OTHERWISE NOTED
<br />O
<br />OCCUPANCY SENSOR WATTSTOPPER OR
<br />CEILING MOUNT
<br />EaUAL.
<br />DUPLEX RECEPTACLE
<br />IS" ABOVE FINISHED FLOOR
<br />120V, 20A
<br />UNLESS OTHERWISE NOTED
<br />DOUBLE DUPLEX RECEPTACLE
<br />IS" ABOVE FINISHED FLOOR
<br />120V, 20A
<br />UNLESS OTHERWISE NOTED
<br />GFI
<br />GROUND FAULT RECEPTACLE
<br />ABOVE COUNTER TOP
<br />120V, 20A (WP=WEATHER PROOF)
<br />UNLESS OTHERWISE NOTED
<br />®
<br />SPECIAL PURPOSE RECEPTACLE
<br />VERIFY MOUNTING HEIGHT AND NEMA
<br />208V, 20A
<br />CONFIGURATION
<br />EXHAUST FAN
<br />VERIFY WITH MECHANICAL PLANS
<br />O
<br />JUNCTION BOX
<br />VERIFY REQUIREMENTS
<br />®
<br />CONTROL RELAY
<br />SEE PLANS FOR TYPE
<br />TELEPHONE OUTLET
<br />IS" ABOVE FINISHED FLOOR
<br />3/4" CONDUIT TO ABOVE CEILING
<br />UNLESS OTHERWISE NOTED
<br />TELEPHONE/DATA OUTLET
<br />15" ABOVE FINISHED FLOOR
<br />3/4" CONDUIT TO ABOVE CEILING
<br />UNLESS OTHERWISE NOTED
<br />CATV OUTLET
<br />IS" ABOVE FINISHED FLOOR
<br />3/4" CONDUIT TO ABOVE CEILING
<br />UNLESS OTHERWISE NOTED
<br />NOTE: NOT ALL ITEMS USED.
<br />LIGHTNING STEEL I
<br />CG19-014
<br />-1:10INNELLY GROUP
<br />CONSULTING EN6INElRS
<br />IL
<br />200 2nd Ave South - #465 - St Petersburg, FL 33701
<br />Info@connellyengineering.com
<br />LD
<br />N
<br />M813.232.8448 (F)800.698.1945
<br />www.connellyengineering.coNR
<br />N
<br />m
<br />FBC. CHAPTER I
<br />105.4.1 PERMIT INTENT .
<br />PROJECT
<br />DATA
<br />O
<br />CU
<br />♦
<br />A PERMIT ISSUED SHALL BE CONSTRUCTED TO BE A LICENSE TO PROCEED WITH THE WORK
<br />AN NOT AS AUTHORITY TO VIOLATE, CANCEL. ALTER OR SET ASIDE ANY OF THE PROVNIIOM
<br />OF THE TECHNICAL CODER. NOR SHALL ISSUANCE OF A PERMIT PREVENT THE BUILDING
<br />DESIGNER
<br />O
<br />OFFOIAL FROM THEREAFTER REOUOWG A CORRECTION OF ERRORS IN PLANS,
<br />LOMETRUCTION OR VIOLATIONS OF THIS CODE. EVERY PERMIT ISSUED SHALL BECOME
<br />AVALIO UNLESS THE WORK AUTHpIQEO BY SUCH PER AT IS COMMENCED WITHM WK
<br />CRC
<br />DRAWN BY
<br />Cy,♦
<br />MONTHS AFTER ITS ISSUANCE. OR IF THE WIN AUTHORREO BY SUCH PERMIT M
<br />W
<br />Q.
<br />SUSPENDED OR ABANDONED FOR A PERIOD OF SIX MONTHS AFTER THE TIME THE WORK IS
<br />COMMENCEO.
<br />PLANE AND CODES OPENS COMPLY WITH THE
<br />THAT APPLICABLE
<br />OF
<br />REOUREMFNT80FTNEAPPLICABLEBULOMIGCODEBSPELFff00NTHE TITLE SMUT
<br />RE HEREBY REQUIREMENTS
<br />JJC
<br />CHECKED
<br />p
<br />CRC
<br />I-
<br />o
<br />J
<br />IL
<br />F_
<br />W
<br />W
<br />x
<br />s
<br />�
<br />a
<br />m
<br />FBC
<br />0
<br />(tJ
<br />0 C3
<br />6TH EDITION
<br />fU
<br />in
<br />m
<br />(2017)
<br />iu
<br />a
<br />CONNELLY GROUP CONSULTING ENGINEERS AND THEIR
<br />c
<br />AGENTS, RESERVES THE RIGHT TO REVISE DETAILS
<br />>
<br />SHOWN HERE AT SUCH TIME AS REVISIONS WILL RESULT
<br />a
<br />IN ENGINEERING OR ECONOMIC IMPROVEMENTS. THESE
<br />m
<br />DRAWINGS ARE GRAPHIC REPRESENTATION OF A DESIGN
<br />F-
<br />W
<br />CONCEPT. ACTUAL DETAILS SUBJECT TO FIELD
<br />w
<br />VERIFICATION.
<br />x
<br />N
<br />W
<br />N
<br />MT
<br />La
<br />cn
<br />O
<br />cn
<br />O
<br />Z
<br />W
<br />U
<br />Cn
<br />cn
<br />H
<br />Z
<br />O
<br />a
<br />LIl7
<br />o
<br />Lo 11.1-
<br />cu =
<br />3
<br />J z
<br />o w
<br />�1' N
<br />DRAWING SETS
<br />REVIEW 11.14.18 (011 - 12.04.18102)
<br />810 00.00.00
<br />PERMIT (80 REVIEW) 09.04.18
<br />PROFESSIONAL SEAL
<br />DATE SEALED: SEPTEMBER. 04.2019
<br />�ppp9�0���BppO�
<br />000�'�� E
<br />If 2OOr
<br />O
<br />©�� T OF /��
<br />-� ��
<br />O��o�
<br />� ORI'D,NAL
<br />�4eoouoouaa��®
<br />W
<br />J
<br />Q
<br />ELECTRICAL SPECIFICATIONS
<br />H
<br />H
<br />°
<br />1
<br />E500
<br />tO n
<br />
|