|
SECTION 102600 - WALL AND DOOR PROTECTION
<br />PART 1- GENERAL
<br />1.1 PRODUCTS
<br />A. WALL GUARDS
<br />1. PLASTIC CRASH RAIL WITH RETAINER CLIPS
<br />a. SURFACE MOUNTED
<br />2. MANUFACTURER:
<br />a. CONSTRUCTION SPECIALTIES: SCR-50 ACROVYN 4000 CRASH
<br />RAIL. INSTALLED PER MANUFACTURER'S
<br />RECOMMENDATIONS. COLOR: AS SPECIFIED ON
<br />DRAWINGS.
<br />CORNER GUARDS
<br />1. SURFACE MOUNTED, RESILIENT, PLASTIC TYPE: 4 FEET HIGH,
<br />USING RETAINER CLIPS.
<br />2. MANUFACTURER:
<br />a. CONSTRUCTION SPECIALTIES: VA-250 ACROVYN 4000 CORNER GUARD.
<br />ACROVYN 4000 CRASH RAIL, INSTALLED PER MANUFACTURER'S
<br />RECOMMENDATIONS. COLOR: AS SPECIFIED ON DRAWINGS.
<br />B. CART STOP
<br />1. MANUFACTURER:
<br />a. MCCUE CORPORATION, CART STOP SP (SUPER); PRODUCT
<br />#CSS-(LENGTH)-A-401. INSTALLED PER MANUFACTURER'S
<br />RECOMMENDATIONS. LENGTH AS INDICATED ON DRAWINGS. COLOR:
<br />AS SPECIFIED ON DRAWINGS.
<br />C. CART CARAL
<br />1. MANUFACTURER:
<br />a. MCCUE CORPORATION, CART STOP GR (GUIDANCE RAIL); INSTALLED
<br />PER MANUFACTURER'S RECOMMENDATIONS. LENGTH AS INDICATED
<br />ON DRAWINGS.
<br />END OF SECTION
<br />SECTION 102800 - TOILET, BATH AND LAUNDRY ACCESSORIES
<br />PART 1 GENERAL
<br />1.01 SECTION INCLUDES
<br />A. GRAB BARS.
<br />1.02 RELATED SECTIONS
<br />A. SECTION 061000-FIRE RETARDANT WOOD BLOCKING AND CURBING:
<br />CONCEALED SUPPORTS FOR ACCESSORIES, INCLUDING IN WALL
<br />FRAMING AND PLATES.
<br />1.03 REFERENCES
<br />1.04 SUBMITTALS
<br />A. SEE SECTION 013000 - ADMINISTRATIVE REQUIREMENTS, FOR
<br />SUBMITTAL PROCEDURES.
<br />B. PRODUCT DATA: PROVIDE DATA ON ACCESSORIES DESCRIBING SIZE,
<br />FINISH, DETAILS OF FUNCTION, ATTACHMENT METHODS.
<br />1.05 COORDINATION
<br />A. COORDINATE THE WORK WITH THE PLACEMENT OF INTERNAL WALL
<br />REINFORCEMENT TO RECEIVE ANCHOR ATTACHMENTS.
<br />PART 2 PRODUCTS
<br />2.01 MANUFACTURERS
<br />A. REFER TO SCHEDULE ON DRAWINGS.
<br />B. OTHER ACCEPTABLE MANUFACTURERS:
<br />1. SUBSTITUTIONS: SECTION 016000 - PRODUCT REQUIREMENTS.
<br />PART 3 EXECUTION
<br />3.01 EXAMINATION
<br />A. VERIFY EXISTING CONDITIONS BEFORE STARTING WORK.
<br />B. VERIFY EXACT LOCATION OF ACCESSORIES FOR INSTALLATION.
<br />C. VERIFY THAT FIELD MEASUREMENTS ARE AS INDICATED ON
<br />DRAWINGS.
<br />3.02 PREPARATION
<br />A. DELIVER INSERTS AND ROUGH -IN FRAMES TO SITE FOR TIMELY
<br />INSTALLATION.
<br />B. PROVIDE TEMPLATES AND ROUGH -IN MEASUREMENTS AS REQUIRED.
<br />3.03 INSTALLATION
<br />A. INSTALL ACCESSORIES IN ACCORDANCE WITH MANUFACTURERS'
<br />INSTRUCTIONS.
<br />B. INSTALL PLUMB AND LEVEL, SECURELY AND RIGIDLY ANCHORED TO
<br />SUBSTRATE.
<br />C. MOUNTING HEIGHTS AND LOCATIONS: AS REQUIRED BY
<br />ACCESSIBILITY REGULATIONS AND AS INDICATED ON DRAWINGS
<br />END OF SECTION
<br />SECTION 104416 - FIRE EXTINGUISHERS
<br />PART 1- GENERAL
<br />1.1 SUMMARY
<br />A. SECTION INCLUDES PORTABLE, HAND -CARRIED FIRE EXTINGUISHERS
<br />AND MOUNTING BRACKETS FOR FIRE EXTINGUISHERS.
<br />1.2 QUALITY ASSURANCE
<br />A. NFPA COMPLIANCE: FABRICATE AND LABEL FIRE EXTINGUISHERS TO
<br />COMPLY WITH NFPA 10, "PORTABLE FIRE EXTINGUISHERS."
<br />B. FIRE EXTINGUISHERS: LISTED AND LABELED FOR TYPE, RATING, AND
<br />CLASSIFICATION BY AN INDEPENDENT TESTING AGENCY ACCEPTABLE
<br />TO AUTHORITIES HAVING JURISDICTION.
<br />1.3 WARRANTY
<br />A. SPECIAL WARRANTY: MANUFACTURER'S STANDARD FORM IN WHICH
<br />MANUFACTURER AGREES TO REPAIR OR REPLACE FIRE
<br />EXTINGUISHERS THAT FAIL IN MATERIALS OR WORKMANSHIP WITHIN
<br />SPECIFIED WARRANTY PERIOD.
<br />1. FAILURES INCLUDE, BUT ARE NOT LIMITED TO, THE FOLLOWING:
<br />a. FAILURE OF HYDROSTATIC TEST ACCORDING TO NFPA 10.
<br />b. FAULTY OPERATION OF VALVES OR RELEASE LEVERS.
<br />2. WARRANTY PERIOD: MANUFACTURER'S STANDARD FORM AND
<br />TERM.
<br />PART 2 - PRODUCTS
<br />2.1 PORTABLE, HAND -CARRIED FIRE EXTINGUISHERS
<br />A. FIRE EXTINGUISHERS: TYPE, SIZE, AND CAPACITY FOR EACH
<br />MOUNTING BRACKET INDICATED.
<br />1. MANUFACTURERS: SUBJECT TO COMPLIANCE WITH
<br />REQUIREMENTS, AVAILABLE MANUFACTURERS OFFERING
<br />PRODUCTS THAT MAY BE INCORPORATED INTO THE WORK
<br />INCLUDE, BUT ARE NOT LIMITED TO, THE FOLLOWING:
<br />a. ANSUL INCORPORATED, TYCO INTERNATIONAL LTD.
<br />b. BUCKEYE FIRE EQUIPMENT COMPANY.
<br />c. LARSEN'S MANUFACTURING COMPANY.
<br />d. MOON-AMERICAN.
<br />e. PYRO-CHEM, TYCO SAFETY PRODUCTS.
<br />2. INSTRUCTION LABELS: INCLUDE PICTORIAL MARKING SYSTEM
<br />COMPLYING WITH NFPA 10, APPENDIX B.
<br />B. DRY -CHEMICAL TYPE: UL-RATED 10 LB. ABC, WITH MONOAMMONIUM
<br />PHOSPHATE BASED CHEMICAL IN STAINLESS -STEEL CONTAINER, WITH
<br />PRESSURE -INDICATING GAGE.
<br />2.2 MOUNTING BRACKETS
<br />A. MOUNTING BRACKETS: MANUFACTURER'S STANDARD GALVANIZED
<br />STEEL, DESIGNED TO SECURE FIRE EXTINGUISHER TO WALL OR
<br />STRUCTURE, OF SIZES REQUIRED FOR TYPES AND CAPACITIES OF
<br />FIRE EXTINGUISHERS INDICATED, WITH PLATED OR RED
<br />BAKED -ENAMEL FINISH.
<br />B. IDENTIFICATION: LETTERING COMPLYING WITH AUTHORITIES HAVING
<br />JURISDICTION FOR LETTER STYLE, SIZE, SPACING, AND LOCATION.
<br />LOCATE AS INDICATED BY ARCHITECT.
<br />1. IDENTIFY BRACKET -MOUNTED FIRE EXTINGUISHERS WITH THE
<br />WORDS "FIRE EXTINGUISHER" IN RED LETTER DECALS APPLIED
<br />TO MOUNTING SURFACE.
<br />a. ORIENTATION: VERTICAL.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. EXAMINE FIRE EXTINGUISHERS FOR PROPER CHARGING AND
<br />TAGGING.
<br />1. REMOVE AND REPLACE DAMAGED, DEFECTIVE, OR
<br />UNDERCHARGED FIRE EXTINGUISHERS.
<br />B. INSTALL FIRE EXTINGUISHERS AND MOUNTING BRACKETS IN
<br />LOCATIONS INDICATED AND IN COMPLIANCE WITH REQUIREMENTS OF
<br />ZAUTHORITIES HAVING JURISDICTION.
<br />1. MOUNTING BRACKETS: 54 INCHES (1372 MM) ABOVE FINISHED
<br />FLOOR TO TOP OF FIRE EXTINGUISHER.
<br />C. MOUNTING BRACKETS: FASTEN MOUNTING BRACKZETS TO
<br />SURFACES, SQUARE AND PLUMB, AT LOCATIONS INDICATED.
<br />END OF SECTION
<br />SECTION 124813 - CARPET TILING
<br />PART1- GENERAL
<br />1.01 SUMMARY
<br />A. SECTION INCLUDES: CARPET TILING
<br />1.02 REFERENCES
<br />A. STANDARDS LISTED BY REFERENCE, INCLUDING REVISIONS BY
<br />ISSUING AUTHORITY, FORM A PART OF THIS SPECIFICATION SECTION
<br />TO EXTENT INDICATED. THE STANDARDS LISTED HERE ARE
<br />IDENTIFIED WITH A DESIGNATION NUMBER, TITLE OR OTHER
<br />DESIGNATION ESTABLISHED BY THE ISSUING AUTHORITY.
<br />B. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM):
<br />1. ASTM C1028 STATIC COEFFICIENT OF FRICTION
<br />1.03 SYSTEM DESCRIPTION
<br />A. PERFORMANCE REQUIREMENTS: PROVIDE CARPET TILES, WHICH HAS
<br />BEEN MANUFACTURED AND INSTALLED TO MAINTAIN PERFORMANCE
<br />CRITERIA STATED BY MANUFACTURER WITHOUT DEFECTS, DAMAGE
<br />OR FAILURE.
<br />1.04 SUBMITTALS
<br />A. GENERAL: SUBMIT LISTED SUBMITTALS IN ACCORDANCE WITH THE
<br />CONDITIONS OF THE CONTRACT AND DIVISION 1 SUBMITTAL
<br />PROCEDURES SECTION.
<br />B. PRODUCT DATA: SUBMIT PRODUCT DATA, INCLUDING
<br />MANUFACTURER'S SPECIFICATION SHEET AND INSTALLATION
<br />INSTRUCTIONS FOR SPECIFIED PRODUCTS. INCLUDE METHODS OF
<br />INSTALLATION AND SUBSTRATE PREPARATION FOR EACH TYPE OF
<br />SUBSTRATE.
<br />C. SHOP DRAWINGS: SUBMIT SHOP DRAWINGS SHOWING LAYOUT,
<br />ACCESSORIES, FINISH COLORS, PATTERNS AND TEXTURES.
<br />D. SAMPLES: SUBMIT SAMPLES FOR EACH TYPE AND COLOR OF
<br />EXPOSED CARPET TILE, THRESHOLD FRAME REDUCERS AND
<br />ACCESSORIES REQUIRED.
<br />E. CLOSEOUT SUBMITTALS: (1) CLEANING & MAINTENANCE DATA
<br />(INCLUDE METHODS FOR MAINTAINING INSTALLED PRODUCTS AND
<br />PRECAUTIONS AGAINST CLEANING MATERIALS AND METHODS
<br />DETRIMENTAL TO FINISHES AND PERFORMANCE), AND (2) WARRANTY.
<br />1.05 QUALITY ASSURANCE
<br />A. INSTALLER: INSTALLER SHOULD BE HIGHLY EXPERIENCED IN
<br />PERFORMING WORK OF THIS SECTION, HAVING PREVIOUSLY DONE
<br />WORK SIMILAR TO THAT REQUIRED FOR THIS PROJECT.
<br />1.06 SEQUENCING/SCHEDULING
<br />A. ORDERING: COMPLY WITH MANUFACTURER'S ORDERING
<br />INSTRUCTIONS AND LEAD-TIME REQUIREMENTS TO AVOID
<br />CONSTRUCTION DELAYS.
<br />B. DELIVERY: DELIVER MATERIALS IN MANUFACTURER'S ORIGINAL,
<br />UNOPENED, UNDAMAGED PACKAGING.
<br />C. STORAGE: STORE MATERIALS AT TEMPERATURE AND IN HUMIDITY
<br />CONDITIONS RECOMMENDED BY MANUFACTURER AND PROTECT
<br />FROM EXPOSURE TO HARMFUL WEATHER CONDITIONS.
<br />D. INSTALLATION: EXCEPT AS OTHERWISE INDICATED HEREIN,
<br />SEQUENCING OR SCHEDULING FOR PERFORMANCE OF WORK OF THIS
<br />SECTION IN RELATION WITH OTHER WORK IS CONTRACTOR'S OPTION.
<br />DELAY INSTALLATION OF MATS UNTIL NEAR TIME OF SUBSTANTIAL
<br />COMPLETION FOR THE PROJECT.
<br />1.07 PROJECT CONDITIONS
<br />A. TEMPERATURE: MAINTAIN TEMPERATURE WHERE PRODUCTS WILL BE
<br />INSTALLED BEFORE, DURING AND AFTER INSTALLATION AS
<br />RECOMMENDED BY MANUFACTURER.
<br />PART 2 - PRODUCTS
<br />2.01 CONSTRUCTION SPECIALTIES
<br />A. DESIGN STEP ENTRANCE CARPET:
<br />B. PATTERN: AS NOTED ON DRAWINGS.
<br />C. COLOR: AS NOTED ON DRAWINGS.
<br />2.02 MATERIALS
<br />A. SURFACE MOUNTED APPLICATION WITH J" GLUE DOWN REDUCER.
<br />AS SPECIFIED ON DRAWINGS.
<br />2.03 PRODUCT SUBSTITUTIONS
<br />A. SUBSTITUTIONS: NO SUBSTITUTIONS PERMITTED.
<br />PART 3 - EXECUTION
<br />3.01 SUBSTRATE PREPARATION
<br />A. EXAMINE SUBSTRATES AND CONDITIONS WHERE CARPET TILES WILL
<br />BE INSTALLED. DO NOT PROCEED WITH INSTALLATION UNTIL
<br />UNSATISFACTORY CONDITIONS ARE CORRECTED. SUB FLOOR SHALL
<br />BE CLEAN AND DRY, AND WITHIN ACCEPTABLE TOLERANCES.
<br />3.02 INSTALLATION
<br />A. ACCESSORIES: THRESHOLD FRAME OR REDUCER AS RECOMMENDED
<br />BY MANUFACTURES. AS NOTED ON DRAWINGS TO MEET ADA
<br />STANDARDS.
<br />C. GENERAL: STRICTLY COMPLY WITH MANUFACTURER'S INSTALLATION
<br />INSTRUCTIONS AND RECOMMENDATIONS. COORDINATE
<br />INSTALLATION WITH ADJACENT WORK TO ENSURE PROPER
<br />CLEARANCES AND TO PREVENT TRIPPING HAZARDS.
<br />3.03 CLEANING AND PROTECTION
<br />A. GENERAL CLEANING: REFER TO MANUFACTURER'S CLEANING AND
<br />MAINTENANCE INSTRUCTIONS.
<br />B. OWNER'S PERSONNEL: INSTRUCT OWNER'S PERSONNEL IN PROPER
<br />MAINTENANCE PROCEDURES.
<br />C. PROTECTION: PROTECT INSTALLED PRODUCT AND FINISH SURFACES
<br />FROM DAMAGE DURING CONSTRUCTION AND UNTIL ACCEPTANCE.
<br />END OF SECTION
<br />SECTION 033543 - SEALED AND POLISHED/DYED CONCRETE FINISHING
<br />PART 1 - GENERAL
<br />1.01 SUMMARY
<br />A. SECTION INCLUDES:
<br />1. GRINDING OF THE SLAB SURFACE TO RECEIVE CLEAR REACTIVE,
<br />PENETRATING LIQUID HARDENER/DENSIFIER.
<br />2. APPLICATION OF CLEAR REACTIVE, PENETRATING LIQUID
<br />HARDENER AND CONCRETE DYE.
<br />3. PROGRESSIVELY POLISHING AND BURNISHING OF THE SLAB
<br />SURFACE TO ACHIEVE FINISH REQUIREMENTS.
<br />4. APPLICATION OF STAIN RESISTANT SURFACE TREATMENT.
<br />B. RELATED REQUIREMENTS
<br />1. SECTION 014000- QUALTITY REQUIREMENTS.
<br />2. SECTIZN 016000- PRODUCT REQUIREMENTS.
<br />3. SECTION 017300- EXECUTION.
<br />4. SECTION 017700- CLOSEOUT SUBMITTALS.
<br />5. SECTION 033000- CAST -IN -PLACE CONCRETE.
<br />6. SECTION 079200- JOINT SEALANTS
<br />1.02 REFERENCES
<br />A. THE DATE OF THE STANDARD IS THAT IN EFFECT AS THE DATE OF
<br />RECEIPT OF BIDS FOR THE PROJECT.
<br />B. LIVING BUILDING CHALLENGE (LBC).
<br />C. SCIENTIFIC CERTIFICATION SYSTEM (SCS) INDOOR AIR QUALITY GOLD
<br />CERTIFICATION.
<br />D. NSF INTERNATIONAL/NONFOOD COMPOUND REGISTRATION.
<br />E. AMERICAN NATIONAL STANDARD INSTITUTE / NATIONAL FLOOR SAFETY
<br />INSTITUTE ANSI/NSFI B101.1 TEST METHOD FOR MEASURING WET SCOF
<br />OF COMMON HARD -SURFACE FLOOR MATERIALS
<br />F. ASTM INTERNATIONAL (ASTM):
<br />1. C1028 - STANDARD TEST METHOD FOR DETERMINING THE STATIC
<br />COEFFICIENT OF FRICTION OF CERAMIC TILE AND OTHER LIKE
<br />SURFACES BY THE HORIZONTAL DYNAMOMETER PULL -METER
<br />METHOD.
<br />2. C1353 - STANDARD TEST METHOD FOR ABRASION RESISTANCE OF
<br />DIMENSION STONE SUBJECTED TO FOOT TRAFFIC USING A ROTARY
<br />PLATFORM, DOUBLE -HEAD ABRASER
<br />3. D523- STANDARD TEST METHOD FOR SPECULAR GLOSS.
<br />4. D1308 - STANDARD TEST METHOD FOR EFFECT OF HOUSEHOLD
<br />CHEMICALS ON CLEAR AND PIGMENTED ORGANIC FINISHES.
<br />5. D4541 - STANDARD TEST METHOD FOR PULL -OFF STRENGTH OF
<br />COATINGS USING PORTABLE ADHESION TESTERS.
<br />6. E96/96M METHOD B (WATER METHOD) - STANDARD TEST METHODS
<br />FOR WATER VAPOR TRANSMISSZION OF MATERIALS.
<br />7. G154 -STANDARD PRACTICE FOR OPERATING FLUORESCENT
<br />ULTRAVIOLET (UV) LAMP APPARATUS FOR EXPOSURE OF
<br />NONMETALLIC MATERIALS.
<br />1.03 ADMINISTRATIVE REQUIREMENTS
<br />A. PRE -INSTALLATION MEETING: CONVENE BEFORE THE START OF WORK
<br />ON NEW CONCRETE SLABS, PATCHING OF EXISTING CONCRETE SLABS
<br />AND START OF APPLICATION OF CONCRETE FINISH SYSTEM.
<br />1. REQUIRE ATTENDANCE OF PARTIES DIRECTLY AFFECTING WORK
<br />OF THIS SECTION, INCLUDING THE OWNER'S REPRESENTATIVE,
<br />CONTRACTOR, ARCHITECT, CONCRETE INSTALLER, AND
<br />APPLICATOR. MEETING SHOULD ONLY CONVENE WHEN REQUIRED
<br />PARTIES ARE PRESENT.
<br />2. REVIEW THE FOLLOWING:
<br />a. PHYSICAL REQUIREMENTS OF COMPLETED CZONCRETE SLAB AND
<br />SLAB FINISH.
<br />b. LOCATIONS AND TIME OF TEST AREAS.
<br />c. PROTECTION OF SURFACES NOT SCHEDULED FOR FINISH
<br />APPLICATION.
<br />d. SURFACE PREPARATION.
<br />e. APPLICATION PROCEDURE.
<br />f. FINAL APPEARANCE OF DYED CONCRETE.
<br />g. QUALITY CONTROL.
<br />h. CLEANING.
<br />I. PROTECTION OF FINISH SYSTEM.
<br />j. COORDINATION WITH OTHER WORK.
<br />3. PRIOR TO ANY WORK, CONTRACTOR MUST CONDUCT A RH
<br />MOISTURE TEST.
<br />1.04 SUBMITTALS
<br />A. PRODUCT DATA:
<br />1. SUBMIT MANUFACTURER'S PRODUCT DATA SHEETS AND TESTED
<br />PHYSICAL AND PERFORMANCE PROPERTIES ON PRODUCTS TO BE
<br />USED FOR THE WORK.
<br />B. VOC CERTIFICATION: SUBMIT CERTIFICATION THAT PRODUCTS
<br />FURNISHED COMPLY WITH REGULATIONS CONTROLLING USE OF
<br />VOLATILE ORGANIC COMPOUNDS (VOC).
<br />C. CERTIFICATES:
<br />1. CERTIFICATES BY MANUFACTURER STATING THAT INSTALLER IS
<br />LISTED APPLICATOR OF SPECIAL CONCRETE FINISHES, AND HAS
<br />COMPLETED THE NECESSARY TRAINING PROGRAMS.
<br />D. FLOOR PROTECTION PLAN.
<br />E. PROVIDE DOCUMENTATION STATING CONCRETE MOISTURE CONTENT
<br />MEETS MANUFACTURER'S REQUIREMENTS.
<br />1.05 QUALITY ASSURANCE
<br />A. INSTALLER QUALIFICATIONS:
<br />1. APPLICATOR TO BE FAMILIAR WITH THE SPECIFIED
<br />REQUIREMENTS AND THE METHODS NEEDED FOR PROPER
<br />PERFORMANCE OF WORK OF THIS SECTION. APPLICATOR MUST
<br />HAVE AVAILABILITY OF PROPER EQUIPMENT TO PERFORM WORK
<br />WITHIN SCOPE OF THIS PROJECT ON A TIMELY BASIS.
<br />APPLICATOR SHOULD HAVE SUCCESSFULLY PERFORMED A
<br />MINIMUM OF 20 PROJECTS OF SIMILAR SCOPE AND COMPLEXITY.
<br />B. MOCK-UP: ON SITE, PRIOR TO THE START OF THE POLISHED
<br />CONCRETE FINISHING PROCESS.
<br />1. REQUIRE ATTENDANCE OF PARTIES DIRECTLY AFFECTING
<br />WORK OF THIS SECTION, INCLUDING THE CONTRACTOR,
<br />ARCHITECT, APPLICATOR, AND OWNER'S REPRESENTATIVE.
<br />2. NOTIFY THE ABOVE PARTIES ONE WEEK IN ADVANCE OF DATE
<br />AND TIME WHEN MOCK-UP WILL BE COMPLETED.
<br />3. DEMONSTRATE THE MATERIALS, EQUIPMENT AND APPLICATION
<br />METHODS TO BE USED FOR WORK SPECIFIED HEREIN IN
<br />PRE -APPROVED LOCATION APPROXIMATELY 50 SQ. FT. IN AREA
<br />OR AS DIRECTED BY THE ARCHITECT OR OWNER'S
<br />REPRESENTATIVE.
<br />4. RETAIN APPROVED MOCK-UP DURING CONSTRUCTION AS A
<br />STANDARD FOR JUDGING THE COMPLETED WORK. AREAS MAY
<br />REMAIN AS PART OF THE COMPLETED WORK.
<br />1.02 DELIVERY, STORAGE AND HANDLING
<br />A. DELIVER MATERIALS IN ORIGINAL CONTAINERS, WITH SEALS
<br />UNBROKEN, BEARING MANUFACTURER LABELS INDICATING BRAND
<br />NAME AND DIRECTIONS FOR STORAGE.
<br />B. STORE CONCRETE HARDENER/DENSIFIER AND SURFACE
<br />PROTECTANT TREATMENT IN ENVIRONMENT RECOMMENDED ON
<br />PUBLISHED MANUFACTURER'S PRODUCT DATA SHEETS.
<br />1. STORE CONTAINERS UPRIGHT IN A COOL, DRY,
<br />WELL -VENTILATED PLACE, OUT OF THE SUN WITH
<br />TEMPERATURE BETWEEN 40 AND 100 DEGREES F (4 AND 38
<br />DEGREES C).
<br />2. PROTECT FROM FREEZING.
<br />3. STORE AWAY FROM OTHER CHEMICALS AND POTENTIAL
<br />SOURCES OF CONTAMINATION.
<br />4. KEEP LIGHTS, FIRE, SPARKS AND HEAT AWAY FROM
<br />CONTAINERS.
<br />5. DO NOT DROP CONTAINERS OR SLIDE ACROSS SHARP OBJECTS.
<br />6. DO NOT STACK PALLETS MORE THAN THREE HIGH.
<br />7. KEEP CONTAINERS TIGHTLY CLOSED WHEN NOT IN USE.
<br />1.07 FIELD CONDITIONS
<br />A. ENVIRONMENTAL LIMITATIONS:
<br />1. COMPLY WITH MANUFACTURER'S WRITTEN INSTRUCTIONS FOR
<br />SUBSTRATE TEMPERATURE AND MOISTURE CONTENT, AMBIENT
<br />TEMPERATURE AND HUMIDITY, VENTILATION, AND OTHER
<br />CONDITIONS AFFECTING PERFORMANCE AND FINISHING
<br />REQUIREMENTS.
<br />B. CLOSE AREAS TO TRAFFIC DURING FLOOR APPLICATION AND AFTER
<br />APPLICATION FOR TIME PERIOD RECOMMENDED IN WRITING BY
<br />MANUFACTURER.
<br />C. PROTECT THE COMPLETED SLAB TO PREVENT DAMAGE BY THE
<br />OTHER TRADES DURING FLOOR COMPLETION.
<br />D. TEMPERATURE LIMITATIONS: PER MANUFACTURER'S REQUIREMENTS.
<br />E. APPLY WHEN AIR CONDITIONS ARE CALM TO MINIMIZE SURFACE
<br />TREATMENT CONTACTING SURFACE NOT INTENDED TO BE FINISHED.
<br />F. DO NOT APPLY TO FROZEN SUBSTRATE. ALLOW ADEQUATE TIME FOR
<br />SUBSTRATE TO THAW, IF FREEZING CONDITIONS EXIST BEFORE
<br />APPLICATION.
<br />G. TEMPORARY HEAT: PER MANUFACTURER'S REQUIREMENTS.
<br />H. VENTILATION: PROVIDE ADEQUATE VENTILATION IN CONFINED OR
<br />ENCLOSED AREAS IN ACCORDANCE WITH MANUFACTURER'S
<br />INSTRUCTIONS.
<br />PART2-PRODUCTS
<br />2.01 MANUFACTURERS:
<br />A. LATICRETE INTERNATIONAL, INC.
<br />B. PROSOCO
<br />C. FLOROCK
<br />D. METZER / MCGUIRE
<br />2.02 FLOOR FINISH FT-1: LATICRETE L & M AQUAPEL
<br />A. GRIND FLOOR USING PLANETARY GRINDING MACHINE TO REMOVE ANY
<br />RESIDUAL FOREIGN MATERIALS THAT MAY BE PRESENT FROM
<br />PREVIOUS FLOOR FINISHES.
<br />B. IF NEW CONCRETE IS PRESENT, THEN NO GRINDING WILL BE
<br />REQUIRED, APPLY SEALER AS SPECIFIED.
<br />C. ONLY MINOR PREP WILL BE REQUIRED; FILLING DEEP CRACKS,
<br />GRINDING ANY LEADING EDGES IF ANY ARE EXPOSED OR PRESENT.
<br />D. PREPARE SURFACE PER MANUFACTURER'S SPECIFICATION.
<br />2.03 FLOOR FINISH FT-2: PROSOCO CONSOLIDECK SYSTEM
<br />A. GRIND SURFACE WITH #50-80 METAL BOND
<br />B. TOOLING PROGRESS TO #150 HYBRID
<br />C. TRANSITION INTO RESIN TOOLING FOR HONING STARTING AT #80
<br />RESIN, PROGRESS TO #100 RESIN, THEN #200 RESIN
<br />D. APPLY PROSOCO GEMTONE STAIN. COLOR AS SPECIFIED IN FINISH
<br />SCHEDULE.
<br />1. ONCE PROFILE HAS BEEN ESTABLISHED APPLY PROSOCO
<br />GEMTONE LIQUID DYE MIXING ONE (1) 12-OUNCE COLOR PACKET
<br />PER HALF- GALLON OF WATER USING A HVLP SPRAYER AT 500 SF
<br />PER GALLON.
<br />E. APPLY PROSOCO LS DENSIFIER UNTIL REJECTION AT AN AVERAGE
<br />RATE OF 650 SF PER GALLON, MAINTAIN A WET FLOOR FOR NO LESS
<br />THAN 15 MINUTES. ALLOW PRODUCT TO DRY BEFORE CONTINUING.
<br />F. CONTINUE SURFACE HONING WITH #400 RESIN, END POLISH WITH #800
<br />RESIN.
<br />G. APPLY PROSOCO LS GUARD SEALER AT A RATE OF 2,000 - 3,000 SF A
<br />GALLON
<br />H. APPLY SECOND COAT AS NEEDED AFTER FIRST COAT IS TACK FREE.
<br />I. HIGH SPEED BURNISH WITH 1500 GRIT DIAMOND IMPREGNATED PAD OR
<br />AUTO SCRUB WITH WHITE PAD TO REMOVE HAZE
<br />J. LIGHT GRIND 250 SQUARE FEET FOLLOWED BY APPLYING PER
<br />PENETRATING CONCRETE SEALER WITH A HVLP SPRAYER
<br />K. ALL FLOOR PATCH TO BE COMPLETED WITH RAPID REFLOOR XP RHINO
<br />GRAY
<br />L CPAA RATING: CLASS C LEVEL 3
<br />2.04 FLOOR FINISH FT-3: PROSOCO FLOROCK HYBRID SYSTEM
<br />A. PROJECT CONDITIONS:
<br />1. MAINTAIN AMBIENT TEMPERATURE REQUIRED BY
<br />MANUFACTURER 3 DAYS DURING, PRIOR, AND FOR 24 HOURS
<br />AFTER INSTALLATION.
<br />2. APPLICATION MAY PROCEED WHILE AIR, MATERIAL AND
<br />SUBSTRATE TEMPERATURES ARE BETWEEN 60 F AND 90 F
<br />PROVIDING THE SUBSTRATE TEMP IS ABOVE THE DEW POINT.
<br />3. THE RH (RELATIVE HUMIDITY) IN THIS SPECIFIC LOCATION OF
<br />THE APPLICATION SHALL BE LESS THAN 75% AND THE SURFACE
<br />TEMPERATURE SHALL BE AT LEAST 5 F ABOVE THE DEW POINT.
<br />4. THE APPLICATOR SHALL BE SUPPLIED WITH ADEQUATE
<br />LIGHTING EQUAL TO THE FINAL LIGHTING LEVEL DURING THE
<br />PREPARATION AND INSTALLATION OF THE SYSTEM.
<br />B. INSTALLATION PROCESS: SEE SPECIFICATION FOR APPLICATION
<br />INSTRUCTIONS. NOTE EPDXY FINISH WILL BE CLEAR SO THAT THE
<br />STAIN PREVIOUSLY APPLIED PER THE SPECIFICATION WILL TRANSFER
<br />THROUGH. FT-3 CONTAINS THE SAME PRODUCTS AS FT-2 WITH THE
<br />ADDITION OF THE FLOROCK FLOROSPARTIC ZERO (AND #60 ALUM
<br />OXIDE / SHARKSKIN GRIP).
<br />1. GRIND EXISTING -NEW CONCRETE WITH METAL BOND DIAMONDS
<br />#40 USING A PLANETARY GRINDER
<br />2. COMPLETE ANY MINOR PREP; SPALLING, DIVOTS, AND SMALL
<br />CRACKS USING 100% SOLIDS MIXED WITH CABOSIL AND TINTED
<br />TO MATCH COLOR AS SCHEDULED.
<br />a. AS A SUBSTITUTE, A STRUCTURAL REPAIR PRODUCT WITH VERY HIGH
<br />ADHESIVE AND TENSILE PROPERTIES SUCH AS METZER / MCGUIRE
<br />RAPID REFLOOR MAY BE USED.
<br />3. ONCE PROFILE HAS BEEN ESTABLISHED APPLY PROSOCO
<br />GEMTONE LIQUID DYE MIXING ONE (1) 12-OUNCE COLOR PACKET
<br />PER 1/2 GALLON OF WATER (COLOR AS SCHEDULED) USING A
<br />HVLP SPRAYER AT 500 SF PER GALLON.
<br />4. START COATINGS ONCE DYE HAS COMPLETELY DRIED:
<br />a. MIX AND APPLY FLOROSPARTIC ZERO CLEAR (BASECOAT) WITH A
<br />FLAT OR 1/8" NOTCHED SQUEEGEE AND ROLL OUT AT 200-300 SF/GAL
<br />b. MIX AND APPLY FLOROSPARTIC ZERO CLEAR (TOPCOAT) WITH A FLAT
<br />OR 1/8" NOTCHED SQUEEGEE AND ROLL OUT AT 200-300 SF/GAL
<br />c. WHILE STILL WET, BROADCAST SIZE #46 ALUMINUM OXIDE AND
<br />SHARKSKIN AT A RATIO OF 1:1 FOR ADDED SLIP RESISTANCE
<br />C. WET AREA COATING APPLICATION PROJECT CONDITIONS:
<br />1. MAINTAIN AMBIENT TEMPERATURE REQUIRED BY
<br />MANUFACTURER 3 DAYS DURING, PRIOR, AND FOR 24 HOURS
<br />AFTER INSTALLATION
<br />2. APPLICATION MAY PROCEED WHILE AIR, MATERIAL AND
<br />SUBSTRATE TEMPERATURES ARE BETWEEN 60 F AND 90 F
<br />PROVIDING THE SUBSTRATE TEMP IS ABOVE THE DEW POINT
<br />3. THE RH (RELATIVE HUMIDITY) IN THIS SPECIFIC LOCATION OF
<br />THE APPLICATION SHALL BE LESS THAN 75% AND THE SURFACE
<br />TEMPERATURE SHALL BE AT LEAST 5 F ABOVE THE DEW POINT.
<br />4. THE APPLICATOR SHALL BE SUPPLIED WITH ADEQUATE
<br />LIGHTING EQUAL TO THE FINAL LIGHTING LEVEL DURING THE
<br />PREPARATION AND INSTALLATION OF THE SYSTEM.
<br />D. SAFETY REQUIREMENTS:
<br />1. NON -RELATED PERSONNEL IN THE WORK AREA SHALL BE KEPT TO A
<br />MINIMUM.
<br />2.05 CONTROL JOINTS
<br />A. CLEAN AND HONOR ALL CONTROL JOINTS THROUGHOUT WITH METZER
<br />SPAL-PRO RS 88 POLYURIA JOINT FILLER (COLOR TO MATCH FLOORING
<br />AS SCHEDULED).
<br />B. JOINTS WILL BE FILLED IN ONE PASS, FILLING FROM BOTTOM TO TOP,
<br />SLIGHTLY OVERFILLING THE JOINT TO LEAVE A CROWNED PROFILE
<br />THEN ALLOWED TO CURE.
<br />C. SHAVE OR RAZOR OFF ALL EXCESS NO SOONER THAN 2 HOURS AND
<br />NO LATER THAN 24 HOURS AFTER INSTALLATION.
<br />PART 3 EXECUTION
<br />3.01 EXAMINATION
<br />A. EXAMINE SUBSTRATE WITH INSTALLER PRESENT FOR CONDITIONS
<br />AFFECTING PERFORMANCE OF FINISH. CORRECT CONDITIONS
<br />DETRIMENTAL TO TIMELY AND PROPER WORK. NOTIFY THE
<br />ARCHITECT AND OWNER'S REPRESENTATIVE IN WRITING OF
<br />CONDITIONS DETRIMENTAL TO THE PROPER AND TIMELY COMPLETION
<br />OF THE WORK.
<br />B. DO NOT BEGIN INSTALLATION UNTIL UNSATISFACTORY CONDITIONS
<br />ARE RESOLVED. BEGINNING WORK CONSTITUTES ACCEPTANCE OF
<br />SITE CONDITIONS AND RESPONSIBILITY FOR DEFECTIVE
<br />INSTALLATION CAUSED BY PRIOR OBSERVABLE CONDITIONS.
<br />3.02 PREPARATION
<br />A. CLEAN DIRT, DUST, OIL, GREASE AND OTHER CONTAMINANTS THAT
<br />INTERFERE WITH PENETRATION OR PERFORMANCE OF SPECIFIED
<br />PRODUCT FROM SURFACES. USE APPROPRIATE CONCRETE
<br />CLEANERS APPROVED BY THE CONCRETE SURFACE TREATMENT
<br />MANUFACTURER WHERE NECESSARY. RINSE THOROUGHLY USING
<br />PRESSURE WATER SPRAY TO REMOVE CLEANER RESIDUES. ALLOW
<br />SURFACES TO DRY COMPLETELY BEFORE APPLICATION OF PRODUCT.
<br />B. REPAIR, PATCH AND FILL CRACKS, VOIDS, DEFECTS AND DAMAGED
<br />AREAS IN SURFACE AS APPROVED BY THE MANUFACTURER. ALLOW
<br />REPAIR MATERIALS TO CURE COMPLETELY BEFORE APPLICATION OF
<br />PRODUCT.
<br />C. VARIATIONS IN SUBSTRATE TEXTURE AND COLOR WILL AFFECT FINAL
<br />APPEARANCE AND SHOULD BE CORRECTED PRIOR TO APPLICATION
<br />OF SEALER/HARDENER SYSTEM AND THE POLISHING STEPS.
<br />D. PROTECT SURROUNDING AREAS PRIOR TO APPLICATION. IF PRODUCT
<br />IS ACCIDENTALLY MISAPPLIED TO ADJACENT SURFACES, FLUSH WITH
<br />WATER IMMEDIATELY BEFORE MATERIAL DRIES.
<br />E. AVOID CONTACT IN AREAS NOT TO BE TREATED. AVOID CONTACT
<br />WITH METAL, GLASS AND PAINTED SURFACES.
<br />F. APPLY SPECIFIED SEALANTS AND CAULKING AND ALLOW COMPLETE
<br />CURING BEFORE APPLICATION OF PENETRATING CONCRETE
<br />HARDENER/DENSIFIER.
<br />G. DO NOT PROCEED UNTIL UNSATISFACTORY CONDITIONS HAVE BEEN
<br />CORRECTED.
<br />3.03 SLAB PROTECTION
<br />A. PROTECT FINISHED FLOORS TO PREVENT DAMAGE INCLUDING
<br />STAINING, GOUGES AND SCRATCHING BY CONSTRUCTION TRAFFIC
<br />AND ACTIVITIES UNTIL POSSESSION.
<br />B. DO NOT DRAG OR DROP EQUIPMENT OR MATERIAL ACROSS THE SLAB
<br />WHICH WILL SCRATCH OR CHIP IT.
<br />C. INSPECT TIRES FOR DEBRIS PRIOR TO USE ON SLAB. REMOVE
<br />EMBEDDED ITEMS WHICH MAY CAUSE DAMAGE TO FLOOR SLAB.
<br />D. CLEAN UP SPILLS ON SLAB IMMEDIATELY. PROVIDE CLEANING
<br />CHEMICALS AND ABSORPTIVE MATERIALS.
<br />E. DEVELOP A CONCRETE PROTECTION PROCEDURE WHICH ADDRESSES
<br />THE FOLLOWING PROCEDURES:
<br />1. COMMUNICATION OF PROTECTION PLAN TO SUBCONTRACTORS
<br />AND VENDORS.
<br />2. PROCEDURES FOR CLEANING UP SLAB SPILLS, INCLUDING USE
<br />OF AND AVAILABILITY OF CLEANING CHEMICALS AND
<br />ABSORPTIVE MATERIALS AT SITE.
<br />F. PROVIDE A CLEAN SLAB USING CONCRETE MAINTENANCE CLEANER
<br />WITHIN AN AUTO SCRUBBER, EQUIPPED WITH SOFT NYLON BRUSHES,
<br />IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS.
<br />3.04 WARRANTIES:
<br />A. FURNISH MANUFACTURERS STANDARD WARRANTY PROVIDING
<br />COVERAGE AGAINST FLOORING DELAMINATION FROM SUBSTRATE AND
<br />DEGRADATION OF SURFACE FINISH.
<br />END OF SECTION
<br />N
<br />f
<br />K
<br />E
<br />•
<br />N
<br />�a0
<br />q
<br />�
<br />N
<br />o
<br />N N
<br />E
<br />b
<br />14
<br />b
<br />d Lg
<br />Z
<br />0
<br />a
<br />U
<br />W
<br />0
<br />W
<br />Q
<br />w
<br />st� •
<br />ISSUED FOR:
<br />PERMIT
<br />03.14.19
<br />BID
<br />03.14.19
<br />CONSTRUCTION
<br />00.00.00
<br />REVIEW SET
<br />03.14.19
<br />PROJECT MANAGER DESIGNER
<br />SS SS
<br />JOB NO.
<br />18390
<br />AS1 07
<br />
|