|
__ I 1' II I ----I I.-I.l-- - - - I ' I I 111''I'll IIII _ ' I - _1 --- I 1 _ - - _ - - ---I _ ---- J Il A II _I
<br />SECTION 064116 - PLASTIC -LAMINATE -CLAD ARCHITECTURAL CABINETS
<br />1.1 SUMMARY
<br />A. SECTION INCLUDES:
<br />PLASTIC -LAIdiINATE-FACED ARCHITECTURAL CABINETS AND COUNTERTOPS AND SOLID SURFACE COUNTERTOPS.
<br />2. WOOD FURRING, BLOCKING, SHIMS, AND HANGING STRIPS FOR INSTALLING PLASTIC -LAMINATE -FACED ARCHITECTURAL
<br />CABINETS UNLESS CONCEALED WITHIN 0", HER CONSTRUCTION BEFtI CABINET INSTALLATION.
<br />1.2 ACTION SUBMITTALS
<br />A. REFER TO THE REQUIRED SUBMi T i� AL LOGIN SECTION n13300 - SUBMITTAL PROCEDURES.
<br />B. PRODUCT DATA: FOR EACH TYPE OF PRODUCT, INCLUDING PANEL PRODUCTS, HIGH-PRESSURE DECORATIVE LAMINATE.
<br />ADHESIVE FOR BONDING PLASTIC LAMINATE, FIRE -RETARDANT -TREATED MATERIALS; AND CABINET HARDWARE AND
<br />ACCESSORIES.
<br />1. FOR !NsTALLAT!ON ADHESIVES, INCLUDING PRINTED STATEIUIEMiT OF'JOC COhITEMI F.
<br />2. FOR ADHESIVES AND COMPOSITE WOOD PROCUC I S, DOCUMENTATION INDICATING THAT PRODUCTS CONTAIN NO UREA
<br />FORMALDEHYDE
<br />C. SHOP DRAWINGS: SHOW LOCATION OF EACH ITEM, DIMENSIONED PLANS AND ELEVATIONS. LARGE-SCALE DETAILS,
<br />ATTACHMENT DEVICES, AND OTHER COMPONENTS.
<br />D. PHYSICAL SAMPLES: VERIFY WITH ARCHITECT.
<br />1.3 QUALITY ASSURANCE
<br />A. FABRICATOR AND INSTALLER QUALIFICATIONS: CERTIFIED PARTICIPANT IN AWI'S QUALITY CERTIFICATION PROGRAM OR
<br />LICENSEE OF WI'S CERTIFIED COMPLIANCE PROGRAM.
<br />IA FIELD CONDITIONS
<br />A. ENV[RONN,II A.L. LIMITATIONS: DO NOT DELIVER, OR INSTALL CAB; NETS JNTiL BUILDING IS ENCLOSED, WET WORK !S
<br />COMPLETE, AND HVAC SYSTEM IS OPERATING AND MAINTAINING TEMPERATURE AND RELATIVE HUMIDITY AT OCCUPANCY
<br />LEVELS DURING THE REMAINDER OF THE CONSTRUCTION PERIOD.
<br />1.5 PLASTiC-LAMINATE-FACED ARCHITECTURAL CABINETS AND COUNTERTOPS
<br />A. QUALITY STANDARD: UNLESS OTHERWISE INDICATED, COMPLY WITH THE "ARCHITECTURAL WOODWORK STANDARDS" FOR
<br />GRADES OF ARCHITECTURAL PLASTIC -LAMINATE CABINETS AND COUNTERTOPS INDICATED FOR CONSTRUCTION, FINISHES,
<br />INSTALLATION, AND OTHER REQUIREMENTS.
<br />B. GRADE: PREMIUM.
<br />C. HIGH-PRESSURE DECORATIVE LAMINATE: NEMA LD 3, GRADES AS INDICATED OR IF NOT INDICATED, AS REQUIRED BY
<br />WOODWORK QUALITY STANDARD.
<br />1. BASIS OF DESIGN: (AS INDICATED ON THE DRAWINGS).
<br />a. WILSONART HIGH PRESSURE LAMINATES.
<br />b. FORMICA HIGH PRESSURE LAMINATES.
<br />2. FINISHES: MATTE FINISH OR AS INDICATED ON DRAWINGS.
<br />3, SURFACE BURNING CHARACTERISTICS IN ACCORDANCE WITH ASTM E84.
<br />4. LAMINATE CLADDING FOR EXPOSED SURFACES:
<br />a. HORIZONTAL SURFACES: GRADE HGS,
<br />b. POSTFORMED SURFACES: GRADE HGP.
<br />C. VERTICAL SURFACES: GRADE VGS.
<br />d. PATTERN DIRECTION: VERTICALLY FOR DRAWER FRONTS, DOORS, AND FIXED PANELS.
<br />5, MATERIALS FOR SEMI EXPOSED SURFACES:
<br />a. SURFACES OTHER THAN DRAWER BODIES; THERMOSET DECORATIVE PANELS.
<br />b. DRAWER SIDES AND BACKS: THERMOSET DECORATIVE PANELS WITH PVC EDGE BANDING.
<br />C. DRAWER, BOTTOMS: THERMOSET DECORATIVE PANELS.
<br />G. CABINET CONSTRUCTION
<br />1. TYPE OF CONSTRUCTION': FRAMELESS.
<br />2. CABINET, DOOR, AND DRAWER FRONT INTERFACE STYLE: FLUSH OVERLAY.
<br />3. REVEAL DIMENSION: AS INDICATED ON CONSTRUCTION DOCUMENTS
<br />H. COUNTERTOP CONSTRUCTION
<br />1. EDGE TREATMENT: 3-MM PVC EDGING OR AS INDICATED.
<br />2. CORE MATERIAL AT SINKS: PARTICLEBOARD MADE WITH EXTERIOR GLUE, MEDIUM -DENSITY FIBERBOARD MADE WITH
<br />EXTERIOR GLUE, OR EXTERIOR -GRADE PLYWOOD.
<br />3, BUILDUP COUNTERTOP THICKNESS TC' 1-ti8' INCHES AT FRONT, BACK, AND ENDS 011TH ADDITIONAL LAYERS OF CORE
<br />III. ER!AL LAMINATED TO TOP
<br />4 BACKER SHEET: PROVIDE PLASTIC-I-AMINATE BACKER SHEET. NENIA LD 3, GRADE BIG.., ON UNDERSIDE OF COUNTERTOP
<br />SUBSTRATE.
<br />I. DUST PANELS! 1/4-INCH PLYWOOD OR TEMPERED HARDBOARD ABOVE COMPARTMENTS AND DRAWERS UNLESS LOCATED
<br />DIRECTLY UNDER TOPS.
<br />1.6 WOOD MATERIALS
<br />A. WOOD PRODUCTS: PROVIDE MATERIALS THAT COMPLY WITH REQUIREMENTS OF REFERENCED QUALI"( STANDARD FOR
<br />EACH TYPE OF WOODWORK AND QUALITY GRADE SPECIFIED UNLESS OTHERWISE INDICATED.
<br />1. WOOD MOISTURE CONTENT: 8 TO 13 PERCENT,
<br />B. COMPOSITE WOOD AND AGRIRBER PRODUCTS: PROVIDE MATERIALS THAT COMPLY WITH REQUIREMENTS OF REFERENCED
<br />QUALITY STANDARD FOR EACH TYPE OF WOODWORK AND QUALITY GRADE SPECIFIED UNLESS OTHERWISE INDICATED.
<br />1. RECYCLED CONTENT OF MEDIUM -DENSITY FIBERBOARD AND PARTICLEBOARD: POSTCONSUMER RECYCLED CONTENT PLUS
<br />ONF-HALF OF P4E-CONSUMER RECYCLED CONTENT NOT LESS THAN 20%PERCENT.
<br />2. COMPOSITE WOOD AND AGRIFIBER PRODUCTS: PRODUCTS SHALL COMPLY WITH THE TESTING AND PRODUCT
<br />REQUIREMENTS OF THE CALIFORNIA DEPARTMENT OF HEALTH SERVICES' "STANDARD PRACTICE FOR THE TESTING OF
<br />VOLATILE ORGANIC EMISSIONS FROM VARIOUS SOURCES USING SMALLSCALE ENVIRONMENTAL CHAMBERS."
<br />3, MEDIUM -DENSITY FIBERBOARD: ANSI A208.2, GRADE 130, PREMIUM GRADE, MADE WITH BINDER CONTAINING NO UREA
<br />FORMALDEHYDE.
<br />4. PARTICLEBOARD: ANSI A208.1, GRADE M-2, MADE WITH BINDER CONTAINING NO UREA FORMALDEHYDE.
<br />5. SOFTWOOD PLYWOOD: DOC PS 1, MEDIUM -DENSITY OVERLAY.
<br />6. MARINE GRADE PLYWOOD: DOC PS 1-95, APA B-B.
<br />7. VENEER -FACED PANEL PRODUCTS (HARDWOOD PLYWOOD): HPVA HP-1, MADE WITH ADHESIVE CONTAINING NO UREA
<br />FORMALDEHYDE.
<br />8. THERMOSET DECORATIVE PANELS: PARTICLEBOARD OR MEDIUM -DENSITY FIBERBOARD FINISHED WITH THERMALLY FUSED,
<br />MELAMINE -IMPREGNATED DECORATIVE PAPER AND COMPLYING WITH REQUIREMENTS OF NEMA LD 3, GRADE VGL, FOR TEST
<br />METHODS 3.3, 3.4, 3.6, 3.8, AND 3,10.
<br />1.7 FIRE -RETARDANT -TREATED MATERIALS
<br />A. FIRE -RETARDANT -TREATED MATERIALS, GENERAL: WHERE FIRE -RETARDANT -TREATED MATERIALS ARE INDICATED, USE
<br />MATERIALS COMPLYING WITH REQUIREMENTS IN THIS ARTICLE THAT ARE ACCEPTABLE TO AUTHORITIES HAVING JURISDICTION
<br />AND WITH FIRE -TEST -RESPONSE CHARACTERISTICS SPECIFIED AS DETERMINED BY TESTING IDENTICAL PRODUCTS PER TEST
<br />METHOD INDICATED BY A QUALIFIED TESTING AGENCY.
<br />1. IDENTIFY FIRE -RETARDANT -TREATED MATERIALS WITH APPROPRIATE CLASSIFICATION MARKING OF QUALIFIED TESTING
<br />AGENCY IN THE FORM OF REMOVABLE PAPER LABEL OR IMPRINT ON SURFACES THAT WILL BE CONCEALED FROM VIEW AFTER
<br />INSTALLATION.
<br />B. FIRE -RETARDANT -TREATED LUMBER ,AND PLYWOOD: PRODUCTS WITH A FLAME -SPREAD INDEX OF 25 OR LESS WHEN
<br />TESTED ACCORDING TO ASTM E 84.'INITH NO EVIDENCE OF SIGNIFICANT PROGRESSIVE COMBUSTION WHEN THE TESTIS
<br />EXTENDED AN ADDITIONAL 20 MINUTES, AND WITH THE FLAME FRONT NOT EXTENDING MORE THAN 10.5 FEET BEYCND THE
<br />CENTERLINE OF THE BURNERS AT ANY TIME DURING THE TEST.
<br />1. KILN DRY LUMBER AND PLYWOOD AFTER TREATMENT TO A MAXIMUM MOISTURE CONTENT OF 19 AND 15 PERCENT,
<br />RESPECTIVELY.
<br />1.8 CABINET HARDWARE AND ACCESSORIES
<br />C. FRAMELESS CONCEALED HINGES (EUROPEAN TYPE): BHMA A!56.9, B01602: 100 DEGREES OF OPENING.
<br />D. PIANO HINGES: BHMA A156.9, STAINLESS STEEL
<br />E. RACK -MOUNTED PULLS: 9HMA A156.9, 1302011.
<br />R ',WIRE PULLS: 2ACK MMOUNTEr�, SOU1) IV%:ETAL, 41INCHES LQii(.';. -3;8" i;":CH. ES DEEP -!NL i 5116 INCH IN Di,A,METER.
<br />G. ADJUSTABLE SHELF STANDARDS AND SUPPORTS: BHMA .A156 9, B040/1; 'i'iiTH SHELF RESTS, 804081.
<br />H. SHELF RESTS: BHh1A A155.92 804013; METAL, TWO rIN TYPE WITH 3,.ELF HOLD-DOWN CLIP.
<br />!. DRAVVER SLIDES: BHMA A156.9.
<br />1. GRADE 1 AND GRADE 2: SIDE MOUNTED AND EXTENDING UNDER BOTTOM EDGE OF DRAWER; FULL EXTENSION TYPE; EPDXY
<br />COATED STEEL WITH POLYMER ROLLERS.
<br />2. GRADE 1HD-100 AND GRADE 1HD-200: SIDE MOUNTED; FULL -EXTENSION TYPE; ZINC -PLATED STEEL BALL -BEARING SLIDES.
<br />3. FOR DRAWERS NOT MORE THAN 3 INCHES (75 MM) HIGH AND NOT MORE THAN 24 INCHES' 600 MM) WIDE, PROVIDE GRADE 1.
<br />4. FOR DRAWERS MORE THAN 3 INCHES (75 MM) HIGH BUT NOT MORE THAN 6 INCHES (150 MM) HIGH AND NOT MORE THAN 24
<br />INCHES (600 MM) WIDE, PROVIDE GRADE 1 HD-100.
<br />5, FOR DRAWERS MORE THAN 6 INCHES (150 MM) HIGH OR MORE THAN 24 INCHES (600 MM) WIDE, PROVIDE GRADE 1HD-200.
<br />6. FOR COMPUTER KEYBOARD SHELVES, PROVIDE GRADE 1HD-100.
<br />7. FOR TRASH BINS PROVIDE GRADE 1HD-200.
<br />J. DOOR LOCKS: BFINIA A156.1 I., E07121.
<br />K. DRAWER LOCKS: BHMA A156.11, E07041,
<br />L. DOOR AND DRAWER SILENCERS: BHMA A156.16, L03011.
<br />M. EXPOSED HARDWARE FINISHES: STAIN STAINLESS STEEL, BHMA 630
<br />N. GROMMETS FOR CABLE PASSAGE THROUGH COUNTERTOPS: 2-INCH, COLOR TO MATCH COUNTERTOP FINISH, MOLDED -
<br />PLASTIC GROMMETS AND MATCHING PLASTIC CAPS WITH SLOT FOR WIRE PASSAGE.
<br />1.9 MISCELLANEOUS MATERIALS
<br />A. FURRING, BLOCKING, SHIMS, AND HANGING STRIPS: FIRE -RETARDANT -TREATED SOFTWOOD LUMBER, KILN DRIED TO LESS
<br />THAN 15 PERCENT MOISTURE CONTENT.
<br />B. ANCHORS: SELECT MATERIAL, TYPE, SIZE, AND FINISH REQUIRED FOR EACH SUBSTRATE FOR SECURE ANCHORAGE.
<br />PROVIDE METAL EXPANSION SLEEVES OR EXPANSION BOLTS FOR POST -INSTALLED ANCHORS. USE NONFERROUS -METAL OR
<br />HOT -DIP GALVANIZED ANCHORS AND INSERTS AT INSIDE FACE OF EXTERIOR WALLS AND AT FLOORS.
<br />C. ADHESIVES: DO NOT USE ADHESIVES THAT CONTAIN UREA FORMALDEHYDE.
<br />D. ADHESIVES: USE ADHESIVES THAT MEET THE TESTING AND PRODUCT REQUIREMENTS OF THE CALIFORNIA DEPARTMENT OF
<br />HEALTH SERVICES' "STANDARD PRACTICE FOR THE TESTING OF VOLATILE ORGANIC EMISSIONS FROM VARIOUS SOURCES
<br />USING SMALL-SCALE ENVIRONMENTAL CHAMBERS."
<br />E. ADHESIVE FOR BONDING PLASTIC LAMINATE: UN -PIGMENTED CONTACT CEMENT.
<br />F. ADHESIVE FOR BONDING EDGES: HOT -MELT ADHESIVE OR ADHESIVE SPECIFIED ABOVE FOR FACES.
<br />1.10 EXAMINATION & PREPARATION
<br />A. EXAMINE SURFACES FOR CONDITIONS THAT WOULD ADVERSELY AFFECT DECORATIVE PLASTIC LAMINATE SURFACING OR
<br />EDGE PERFORMANCE.
<br />B. BEFORE INSTALLATION, CONDITION CABINETS TO AVERAGE PREVAILING HUMIDITY CONDITIONS IN INSTALLATION AREAS.
<br />1.11 INSTALLATION
<br />A. GENERAL: INSTALL DECORATIVE PLASTIC LAMINATE IN ACCORDANCE WITH MANUFACTURER'S WRITTEN INSTALLATION
<br />INSTRUCTIONS, APPROVED SUBMITTALS AND REQUIREMENTS OF DIVISION 6 SECTION "FINISH CARPENTRY" & "INTERIOR
<br />ARCHITECTURAL WOODWORK".
<br />3. INSTALL CABINETS LEVEL, PLUMB, TRUE, AND STRAIGHT. SHIM AS REQUIRED WITH CONCEALED SHIMS. INSTALL LEVEL AND
<br />PLUMB TO A TOLERANCE OF 1/8 INCH IN 96 INCHES.
<br />C. SCRIBE AND CUT CABINETS TO FIT ADJOINING WORK, REFINISH CUT SURFACES, AND REPAIR DAMAGED FINISH AT CUTS.
<br />D. ANCHOR CABINETS TO ANCHORS OR BLOCKING BUILT IN OR DIRECTLY ATTACHED TO SUBSTRATES. SECURE WITH
<br />COUNTERSUNK, CONCEALED FASTENERS AND BLIND NAILING. USE FINE FINISHING NAILS OR FINISHING SCREWS FOR EXPOSED
<br />FASTENING, COUNTERSUNK AND FILLED FLUSH WITH WOODWORK.
<br />E. CABINETS: INSTALL WITHOUT DISTORTION SO DOORS AND DRAWERS FIT OPENINGS PROPERLY AND ARE ACCURATELY
<br />ALIGNED. ADJUST HARDWARE TO CENTER DOORS AND DRAWERS IN OPENINGS AND TO PROVIDE UNENCUMBERED OPERATION.
<br />COMPLETE INSTALLATION OF HARDWARE AND ACCESSORY ITEMS AS INDICATED.
<br />SECTION 068316 - FIBERGLASS REINFORCED PANELING
<br />1.1 SECTION INCLUDES: FIBERGLASS REINFORCED PLASTIC (FRP) WALL PANELS.
<br />1.2 ACTION SUBMITTALS: REFER TO THE REQUIRED SUBMITTAL LOGIN SECTION 013300 -SUBMITTAL PROCEDURES
<br />1.3 QUALITY ASSURANCE
<br />A. INSTALLER'S QUALIFICATIONS: INSTALLER REGULARLY ENGAGED, FOR A MINIMUM OF 5 YEARS, IN INSTALLATION OF FRP
<br />PANELS OF SIMILAR TYPE TO THAT SPECIFIED.
<br />B. STORAGE AND HANDLING REQUIREMENTS: STORE AND HANDLE MATERIALS IN ACCORDANCE WITH MANUFACTURER'S
<br />INSTRUCTIONS.
<br />1.4 AMBIENT CONDITIONS
<br />A. FOLLOW MANUFACTURERS WRITTEN INSTRUCTIONS.
<br />B. DURING INSTALLATION AND WITHIN 48 HOURS BEFORE INSTALLATION, MAINTAIN AMBIENT TEMPERATURE AND RELATIVE
<br />HUMIDITY WITHIN LIMITS REQUIRED BY TYPE OF FRP PANEL ADHESIVE USED AND ADHESIVE MANUFACTURER'S INSTRUCTIONS.
<br />1.5 WARRANTY
<br />A. MANUFACTURER'S SPECIAL WARRANTY: MANUFACTURER'S STANDARD FORM IN WHICH MANUFACTURER AGREES TO REPAIR
<br />OR REPLACE FRP PANELS THAT FAIL WITHIN SPECIFIED WARRANTY PERIOD.
<br />B. INSTALLER'S SPECIAL WARRANTY: INSTALLER'S STANDARD FORM IN WHICH INSTALLER AGREES TO REPAIR OR REPLACE FRP
<br />PANELS THAT FAIL DUE TO POOR WORKMANSHIP OR FAULTY INSTALLATION WITHIN SPECIFIED
<br />1.6 FRP PANELS AND ACCESSORIES
<br />A. REFER TO DRAWINGS FOR PRODUCTS AND FINISHES.
<br />B. PANEL DIMENSIONS: USE MAXIMUM MANUFACTURED SIZE.
<br />C. MOLDINGS, TRIM, AND CAPS: 1-PIECE EXTRUDED POLYPROPYLENE OR PVC, CONFIGURED TO COVER PANEL EDGES AND
<br />CORNERS,
<br />D. PANEL ADHESIVE: AS RECOMMENDED BY FRP PANEL MANUFACTURER FOR REQUIRED SUBSTRATES.
<br />1.7 PREPARATION
<br />A. CLEAN SUBSTRATES TO REMOVE SUBSTANCES THAT COULD IMPAIR BOND OF ADHESIVE, INCLUDING OIL, GREASE, DIRT
<br />DUST, OR OTHER CONTAMINATES.
<br />B. ACCLIMATE FRP PANELS BY UNPACKING AND PLACING IN INSTALLATION SPACE A MINIMUM OF 24 HOURS BEFORE
<br />INSTALLATION.
<br />1.8 INSTALLATION
<br />A. INSTALL FRP PANELS IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AT LOCATIONS INDICATED ON THE DRAWINGS
<br />B. INSTALL FRP PANELS PLUMB, LEVEL, SQUARE, FLAT, AND IN PROPER ALIGNMENT.
<br />C. INSTALL TRIM ACCESSORIES WITH ADHESIVE AND NAILS OR STAPLES.
<br />D. SEALANT:
<br />1. FILL GROOVES IN TRIM ACCESSORIES WITH SEALANT BEFORE INSTALLING FRP PANELS.
<br />2. BED INSIDE CORNER TRIM IN BEAD OF SEALANT.
<br />3. REI`I EXCESS SEALANT AND SMEARS AS FRP PANELS ARE INSTALLED.
<br />4. CLEAN IN ACCORDANCE WITH SEALANT MANUFACTURER'S INSTRUCTIONS.
<br />SECTION 072100 o THERMAL AND ACOUSTIC INSULATION
<br />1.1 SUMMARY
<br />A, SECTION INCLUDES:
<br />1. EXTRUDED POLYSTYRENE FOAM -PLASTIC BOARD.
<br />, FIBERGLASS BATT AND BLANKET,
<br />1.2 ACTION SUBMITTALS: REFER TO THE REQUIRED SUBMITTAL LOG IN SECTION 013300 - SUBMITTAL PROCEDURES.
<br />1.3 MATERIALS
<br />A. EXTRUDED POLYSTYRENE BOARD, TYPE IV, ASTM C 578, TYPE IV, 25-PSI MINIMUM COMPRESSIVE STRENGTH; UNFACED;
<br />MAXIMUM FLAME -SPREAD AND SMOKE -DEVELOPED INDEXES OF 25 AND 450, RESPECTIVELY, PER ASTM E 84. MINIMUM R-5 PER
<br />INCH,
<br />B. MINERAL -WOOL BATT, UNFACED: ASTM C 665, TYPE I (BLANKETS WITHOUT MEMBRANE FACING); CONSISTING OF FIBERS; WITH
<br />MAXIMUM FLAME -SPREAD AND SMOKE -DEVELOPED INDEXES OF 25 AND 50, RESPECTIVELY, PER ASTM E 84; PASSING ASTM E 136
<br />FOR COMBUSTION CHARACTERISTICS. MINIMUM R-3.5 PER INCH.
<br />C. MINERAL -WOOL BLANKET, REINFORCED -FOIL FACED: ASTM C 665, TYPE III (REFLECTIVE FACED), CLASS A (FACED SURFACE
<br />WITH A FLAME -SPREAD INDEX OF 25 OR LESS PER ASTM E 84); CATEGORY 1(MEMBRANE IS A VAPOR BARRIER), FACED WITH FOIL
<br />SCRIM, FOIL -SCRIM KRAFT, OR FOIL -SCRIM POLYETHYLENE. MINIMUM R-3.5 PER INCH.
<br />D. FIBERGLASS BATT, UNFACED: ASTM C 665, TYPE II, CLASS C (BLANKETS WITHOUT MEMBRANE FACING); CONSISTING OF
<br />FIBERGLASS FIBERS; WITH MAXIMUM FLAME -SPREAD AND SMOKE -DEVELOPED INDEXES OF 25 AND 50. RESPECTIVELY, PER
<br />ASTM E 84; PASSING ASTM E 136 FOR COMBUSTION CHARACTERISTICS. MINIMUM R-3.5 PER INCH.
<br />C. FIBERGLASS BLANKET, REINFORCED -FOIL FACED: ASTM C 665, TYPE 111, CLASS C (REFLECTIVE FACED), CLASS A (FACED
<br />SURFACE WITH A FLAME -SPREAD INDEX OF 25 OR LESS PER ASTM E 84); CATEGORY 1 (MEMBRANE IS A VAPOR BARRIER), FACED
<br />WITH FOIL SCRIM, FOIL -SCRIM KRAFT, OR FOIL -SCRIM POLYETHYLENE. MINIMUM R-3.5 PER INCH.
<br />1.4 ACCESSORIES
<br />A. VAPOR BARRIER: 10-MIL POLYETHYLENE.
<br />B. INSULATION ANCHORS, SPINDLES, AND STANDOFFS: AS RECOMMENDED BY MANUFACTURER.
<br />C. ADHESIVE FOR BONDING INSULATION: PRODUCT COMPATIBLE WITH INSULATION AND AIR AND WATER BARRIER MATERIALS,
<br />AND WITH DEMONSTRATED CAPABILITY TO BOND INSULATION SECURELY TO SUBSTRATES WITHOUT DAMAGING INSULATION AND
<br />SUBSTRATES.
<br />SECTION 072619 TOPICAL MOISTURE VAPOR EMISSION SYSTEM
<br />1.1 SUMMARY
<br />A., THIS SECTION INCLUDES A SINGLE -COAT, FAST CURING. 100% SOLIDS EPDXY MOISTURE MANAGEMENT SYSTEM FORMULATED
<br />TO SUPPRESS EXCESSIVE MOISTURE VAPOR EMISSIONS IN NEW OR EXISTING CONCRETE.
<br />1.2 ACTION SUBMITTALS
<br />A PRODUCT DATA: SUBMIT MANUFACTURER'S PRODUCT DATA AND INSTALLATION INSTRUCTIONS FOR EACH MATERIAL AND
<br />PRODUCT USED, INCLUDE MANUFACTURER'S MATERIAL SAFETY DATA SHEETS.
<br />1.3 QUALITY ASSURANCE
<br />A, INSTALLATION OF THE MOISTURE MITIGATION PRODUCT MUST BE COMPLETED BY.A CERTIFIED APPLICATOR USING MIXING
<br />EQUIPMENT AND TOOLS APPROVED BY THE MANUFACTURER.
<br />B. PRODUCTS USED FOR WORK IN THIS SECTION SHALL BE MANUFACTURED BY COMPANIES WHICH HAVE SUCCESSFULLY
<br />SPECIALIZED IN PRODUCTION OF THIS TYPE OF WORK FOR NOT LESS THAN 10 YEARS. CONTACT MANUFACTURERS
<br />REPRESENTATIVE PRIOR TO INSTALLATION.
<br />1.4 WARRANTY: MANUFACTURERS STANDARD WARRANTY.
<br />1.5 DELIVERY, STORAGE AND HANDLING: COMPLY WITH MANUFACTURERS WRITTEN INSTRUCTIONS
<br />1.6 PROJECT CONDITIONS: COMPLY WITH MANUFACTURERS WRITTEN INSTRUCTIONS.
<br />1.7 TOPICAL MOISTURE VAPOR EMMISION SYSTEM
<br />A. ONE -COAT MOISTURE CONTROL SYSTEM FOR CONCRETE.
<br />1. BASIS OF DESIGN: ARDEX OR EQUAL APPROVED BY ARCHITECT.
<br />2. PERFORMANCE AND PHYSICAL PROPERTIES: MEET OR EXCEED THE FOLLOWING VALUES FOR MATERIAL CURED AT 70° F+/-3°
<br />F AND 50%+/- 5% RELATIVE HUMIDITY:
<br />a. APPLICATION: MANUAL
<br />b. MATERIAL REQUIREMENTS ON CSP 3 PREPARED CONCRETE: MAX 270 SQ. FT. PER MIXED UNITS FOR 10 MILS.
<br />c. PERMEABILITY (ASTM E96): <0.06 PERMS
<br />d. 14 PH SOLUTION (ASTM D1308): NO EFFECT
<br />e. VOC: OG/L, CALCULATED SCAQMD 1113
<br />f. WALKABLE: MINIMUM OF 4 HOURS
<br />SECTION 072100 TOPICAL MOISTURE VAPOR EMISSION SYSTEM (CONTINUED)
<br />1.8 HYDRAULIC CEMENT UNDERLAYMENT
<br />A. HYDRAULIC CEMENT -BASED SELF -LEVELING UNDERLAYMENT.
<br />1. PERFORMANCE AND PHYSICAL PROPERTIES: MEET OR EXCEED THE FOLLOWING VALUES FOR MATERIAL CURED AT 70" F
<br />+/-3° F AND 50%+/I RELATIVE HUMIDITY:
<br />a. APPLICATION: BARREL MIX OR PUMP
<br />b FLOW TIME: 10 MINUTES
<br />c. INITIAL SET: APPROX. 30 MINUTES
<br />d. FINAL SET: APPROX. 90 MINUTES
<br />e. COMPRESSIVE STRENGTH: MINIMUM 4100 PSI AT 28 DAYS, ASTM C109M.
<br />f. FLEXURAL STRENGTH: 10% PSI AT 23 DAYS, ASTM C78.
<br />g. VOC: 0 G1, CALCULATED SCAQMD 1113
<br />1.9 WATER
<br />A. WATER SHALL BE CLEAN, POTABLE, AND SUFFICIENTLY COOL (NOT WARMER THAN 70- F).
<br />1.10 PREPARATION
<br />A. CONCRETE SUBFLOORS: PREPARE SUBSTRATE IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS,
<br />1. PRIOR TO PROCEEDING, REFER TO ASTM F710 STANDARD PRACTICE FOR PREPARING CONCRETE FLOORS TO RECEIVE
<br />RESILIENT FLOORING. ALL CONCRETE SUBFLOORS MUST BE SOUND, SOLID, CLEAN, AND FREE OF ALL OIL, GREASE, DIRT,
<br />CURING COMPOUNDS AND ANY SUBSTRATE THAT MIGHT ACT AS A BOND BREAKER BEFORE APPLICATION,
<br />2. MECHANICALLY PREPARE THE SURFACE TO OBTAIN A MINIMUM ICRI CONCRETE SURFACE PROFILE OF 3 (CSP 3). THE
<br />SUBSTRATE PREPARATION MUST BE BY MECHANICAL MEANS, SUCH AS SHOT BLASTING.
<br />3. THE CONCRETE MIDST HAVE A MINIMUM TENSILE STRENGTH OF AT LEAST 150 PSI FOR AREAS TO RECEIVE NORMAL FOOT
<br />TRAFFIC, AND 200 PSI FOR AREA OF HEAVY COMMERCIAL TRAFFIC WHEN TESTED IN ACCORDANCE WITH ASTM C1583. THE
<br />CONCRETE SURFACE CAN BE DAMP, BUT MUST BE FREE OF STANDING WATER.
<br />4, PRIOR TO BEGINNING THE INSTALLATION, MEASURE THE RELATIVE HUMIDITY WITHIN THE CONCRETE (ASTM F2170). FOR
<br />THESE RELATIVE HUMIDITY METHODS, THE RH SHALL NOT EXCEED 100%. NO STANDING WATER SHALL BE PRESENT.
<br />5. TO ACHIEVE A CONTINUOUS MOISTURE BARRIER, FORMANT CONTROL JOINTS AND DORMANT CRACKS GREATER THAN A
<br />HAIRLINE (1/32") MUST BE PRE -FILLED WITH A TWO-PART, LOW VISCOSITY, 100% SOLIDS, RIGID CRACK AND JOINT FILLER.
<br />FORMANT CRACKS AND DORMANT SAW CUTS MUST BE FILLED IN STRICT ACCORDANCE WITH THE MANUFACTURER'S
<br />INSTALLATION INSTRUCTIONS, ONCE THE DORMANT CRACKS AND DORMANT SAW CUTS HAVE BEEN FILLED PROPERLY,
<br />BROADCAST SAND TO REFUSAL, AND ALLOW THESE AREAS TO SURE THOROUGHLY, REMOVE ALL EXCESS SAND PRIOR TO
<br />PROCEEDING.
<br />1.11 INSTALLATION
<br />A, EXAMINE SUBSTRATE AND CONDITIONS UNDER WHICH MATERIALS WILL BE INSTALLED. DO NOT PROCEED WITH
<br />INSTALLATION UNTIL UNSATISFACTORY CONDITIONS ARE CORRECTED.
<br />B. COORDINATE INSTALLATION WITH ADJACENT WORK TO ENSURE PROPER SEQUENCE OF CONSTRUCTION. PROTECT
<br />ADJACENT AREAS FROM CONTACT DUE TO MIXING AND HANDLING OF MATERIALS.
<br />C. MIXING: COMPLY WITH MANUFACTURER'S PRINTED INSTRUCTIONS.
<br />D. APPLICATION: COMPLY WITH MANUFACTURE'S PRINTED INSTRUCTIONS.
<br />1.12 PROTECTION
<br />A. PRIOR TO THE INSTALLATION OF THE FINISH FLOORING, THE SURFACE OF THE UNDERLAYMENT SHOULD BE PROTECTED
<br />FROM ABUSE BY OTHER TRADES BY THE USE OF PLYWOOD, MASONITE OR OTHER SUITABLE PROTECTION COURSE.
<br />SECTION 07 8400 - FIRESTOPPING
<br />1.1 SECTION INCLUDES FIRESTOPPING MATERIALS AT OPENINGS, PENETRATIONS, VOIDS, AND PERIPHERY OF FIRE RATED
<br />CONSTRUCTION. WORK INCLUDES. BUT NOT LIMITED TO, FIRESTOPPING JOINTS IN THE FOLLOWING:
<br />A. WALLS AND PARTITIONS ABU T T!NG OTHER MATERIALS INCLUDING DECK.
<br />B. PENETRATIONS IN WALLS, PARTITIONS, OR SHAFTS,
<br />C. PENETRATIONS IN FLOOR ASSEMBLIES,
<br />1.2 FIRESTOPPING RESPONSIBILITY: THE TRADE CAUSING, REQUIRING THE LARGEST PROPORTION OF THE PENETRATION.
<br />1.3 FIRESTOPPING DEFINED: AN ASSEMBLY TO RETAIN THE INTEGRITY OF TIME RATED CONSTRUCTION BY MAINTAINING AN
<br />EFFECTIVE BARRIER AGAINST THE SPREAD OF FLAME, SMOKE, AND GASES AT PENETRATIONS AND VOIDS.
<br />1.4 REFERENCE STANDARDS
<br />A. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM): E 119-98 FIRE TESTS OF BUILDING CONSTRUCTION AND
<br />MATERIALS. E 814-97 FIRE TESTS OF THROUGH -PENETRATION FIRE STOPS.
<br />B. NATIONAL FIRE PROTECTION ASSOCIATION (NFPA): 70-1996 NATIONAL ELECTRIC CODE 101-1997 CODE FOR SAFETY TO LIFE
<br />FROM FIRE IN BUILDINGS AND STRUCTURES (LIFE SAFETY CODE).
<br />C. UNDERWRITERS LABORATORIES (UL): UL 1479 FIRE TESTS OF THROUGH -PENETRATION FIRE STOPS UL 2079 TESTS FOR FIRE
<br />RESISTANCE OF BUILDING JOINT SYSTEMS. FIRE RESISTANCE DIRECTORY, 1998 OR LATEST EDITION.
<br />1.5 PERFORMANCE REQUIREMENTS:
<br />A. FIRESTOPPING TO MEET THE REQUIREMENTS LISTED BELOW FOR A DURATION NOT LESS THAN REQUIRED FOR THE TIME
<br />RATED CONSTRUCTION ASSEMBLY. PENETRATIONS; ASTM E 814, PERIMETER OPENINGS; ASTM E 119.
<br />B. FIRESTOPPING IN FLOORS HAVING VOID OPENINGS OF 4 INCHES OR MORE TO BE REINFORCED OR COVERED TO SUPPORT
<br />THE FLOOR LOAD REQUIREMENTS; ALL IN A MANNER ACCEPTABLE TO THE ARCHITECT. FIRESTOPPING TO ACCOMMODATE
<br />DIFFERENTIAL DEFLECTION AND MOVEMENT BETWEEN ADJACENT SUBSTRATES WITHOUT DAMAGE TO SUBSTRATES,
<br />FIRESTOPPING, LOSS OF FIRESTOPPING PERFORMANCE, AND WITHOUT TRANSFER OF STRUCTURAL LOADS THROUGH
<br />FIRESTOPPING DESIGN.
<br />1.6 SUBMIT PRODUCT DATA, COPIES OF TESTS AND OTHER PRODUCT DATA VERIFYING CONFORMANCE WITH SPECIFIED
<br />PERFORMANCE CHARACTERISTICS AND COMPLETE DESCRIPTION OF ASSEMBLIES AND INSTALLATION METHODS. SHOW
<br />PROPOSED DETAILS OF INSTALLATION, REINFORCING, AND ANCHORAGE. DETAILS SHALL REFLECT ACTUAL JOB CONDITIONS
<br />FOR UNUSUAL CONDITIONS OR CONDITIONS NOT COVERED BY MANUFACTURER'S STANDARD DETAILS, MANUFACTURERS
<br />PRODUCT DATA SHEETS MAY BE SUBMITTED INSTEAD OF SHOP DRAWINGS IF SUBMITTAL INCLUDES ALL REQUIRED
<br />INFORMATION.
<br />1.7 INSTALLER: MUST BE SPECIALISTS IN THE INSTALLATION OF FIRESTOPPING OF THE TYPE REQUIRED
<br />1.8 REGULATORY AGENCIES: COMPLY WITH THE APPLICABLE REQUIREMENTS FOR FIRE SEPARATIONS AND PENETRATIONS OF
<br />THE FOLLOWING: NYC BUILDING CODE, NFPA 70, NFPA 101,
<br />A. FIRESTOPPING TO BE LISTED UNDER UL 1479 AND ACCEPTABLE TO GOVERNING CODES AND LOCAL AUTHORITIES.
<br />B. UNTESTED SYSTEMS: FOR THOSE FIRESTOP APPLICATIONS THAT EXIST FOR WHICH NO UL TESTED SYSTEM IS AVAILABLE
<br />THROUGH ANY MANUFACTURER, SUBMIT A MANUFACTURER'S ENGINEERING JUDGMENT DERIVED FROM SIMILAR UL SYSTEM
<br />DESIGNS OR OTHER TESTS TO LOCAL AUTHORITIES HAVING JURISDICTION FOR THEIR REVIEW AND APPROVAL PRIOR TO
<br />INSTALLATION.
<br />1.9 PROVIDE PRODUCTS FROM ONE OR MORE OF THE FOLLOWING MANUFACTURERS ACCORDING TO THE SUITABILITY OF THE
<br />PRODUCT FOR THE INTENDED PURPOSE.
<br />A. STI (SPECSEAL).
<br />B. 3M CONTRACTOR PRODUCTS.
<br />C NELSON.
<br />D. IPC (INTERNATIONAL PROTECTIVE COATINGS, CORP.)
<br />E. TREMCO.
<br />F. RECTORSEAL,
<br />G. DOW CORNING.
<br />H. US GYPSUM CO.
<br />I. INTERNATIONAL PROTECTIVE COATINGS, CORP.
<br />.J. STANDARD OIL (FYRE PUTTY).
<br />K. GENERAL ELECTRIC (PENSIL).
<br />L. HILTI.
<br />M. FLAMMADUR CORPORATION OF AMERICA
<br />N. FYRESLEEVE INDUSTRIES, INC., BURNARY, BRITISH COLUMBIA.
<br />1.10 PRODUCTS TO BE ASBESTOS FREE AND SUITABLE FOR PENETRATIONS MADE BY STEEL, GLASS, PLASTIC, OR INSULATED
<br />PIPE ACCORDING TO THE ACTUAL MATERIALS USED. FIRE -RATING CLASSIFICATION FOR INSULATED PIPE MUST NOT REQUIRE
<br />REMOVAL OF THE INSULATION,
<br />SEALANTS TO HAVE A VOC LIMIT OF 250 G/L
<br />1.12 EXAMINE SUBSTRATES AND CONDITIONS UNDER WHICH FIRESTOPPING WORK IS TO BE PERFORMED AND NOTIFY
<br />CONSTRUCTION MANAGER OR GENERAL CONTRACTOR IN WRITING OF UNSATISFACTORY CONDITIONS, DO NOT PROCEED WITH
<br />WORK UNTIL UNSATISFACTORY CONDITIONS HAVE BEEN CORRECTED IN MANNER ACCEPTABLE TO INSTALLER. INSTALLATION OF
<br />FIRESTOPPING MATERIALS CONSTITUTES ACCEPTANCE OF SUBSTRATE AND CONDITIONS.
<br />1.13 OBTAIN MANUFACTURER'S INSTRUCTIONS FOR FIRESTOPPING INSTALLATION AND PRACTICES FOR INSTALLING CREW.
<br />CLEAN JOINT SURFACES FREE FROM DIRT, GREASE, OIL, LOOSE MATERIALS, RUST, OR OTHER SUBSTANCES THAT MAY AFFECT
<br />PROPER FITTING OR THE REQUIRED FIRE RESISTANCE.
<br />1.14 UPON COMPLETION, REMOVE AND DISPOSE OF MASKING MATERIALS; REMOVE ALL EXCESS SEALING MATERIALS; CLEAN
<br />ADJACENT EXPOSED SURFACES OF ALL SOIL AND STAIN RESULTING FROM FIRESTOPPING OPERATIONS.
<br />1,15 PROVIDE UL-CLASSIFIED SYSTEMS FOR THE CONDITIONS SPECIFIED BELOW. U.L. CLASSIFIED SYSTEMS REFERENCED
<br />ARE ALPHA -NUMERIC DESIGNATIONS LISTED IN U.L.'S "FIRE RESISTANCE DIRECTORY".
<br />SECTION 079200 - JOINT SEALANTS
<br />1.1 SUMMARY
<br />A. SECTION INCLUDES:
<br />1. SILICONE JOINT SEALANTS.
<br />2. NONSTAINING S!UCONE JOINT SEALANTS,
<br />3, URETHANE JOINT SEALANTS,
<br />4. IMMERSIBLE JOINT SEALANTS.
<br />5. MILDEW -RESISTANT JOINT SEALANTS.
<br />6. LATEX JOINT SEALANTS.
<br />1.2 ACTION SUBMITTALS: REFER TO SECTION 013300 FOR REQUIRED SUBMITTALS.
<br />1.3 QUALITY ASSURANCE: TESTING AGENCY QUALIFICATIONS QUALIFIED .ACCORCI!NG TO ASTM C 1021 -i 0 C;1•^�DUC-i TyF
<br />TESTING INDICATED.
<br />1.4 PRECONSTRUCTION TESTING
<br />A. PRECONSTRUCTION LABORATORY TESTING: SUBMIT TO JOINT -SEALANT MANUFACTURERS, FOR TESTING INDICATED
<br />BELOW, SAMPLES OF MATERIALS THAT WILL CONTACT OR AFFECT JOINT SEALANTS.
<br />1. ADHESION TESTING: USE ASTM C 794 TO DETERMINE WHETHER PRIMING AND OTHER. SPECIFIC JOINT PREPARATION
<br />TECHNIQUES ARE REQUIRED TO OBTAIN RAPID, OPTIMUM ADHESION OF JOINT SEA.LAMITS TO JOINT SUBSTRATES.
<br />2. COMPATIBILITY TESTING: USE ASTM C 1087 TO DETERMINE SEALANT COMPATIBILITY WHEN IN CONTACT WITH GLAZING
<br />AND GASKET MATERIALS.
<br />3. STAIN TESTING: USE ASTM C 1248 TO DETERMINE STAIN POTENTIAL OF SEALANT WHEN !N CONTA!; i 4`VITH iAASC'NRY OR
<br />EFIS SUBSTRATES.
<br />B. PRECONSTRUCTION FIELD -ADHESION TESTING: BEFORE INSTALLING SEALANTS, FIELD TES
<br />T THEIR ADHE
<br />SION TO
<br />PROJECT JOINT SUBSTRATES. TEST JOINT SEALANTS ACCORDING TO METHOD PRELD-APPLIED IEG SEALANT JOINT HAND C PULL
<br />TAB, IN APPENDIX X1.1 IN ASTM C 1193 OR METHOD A, TAIL PROCEDURE, IN ASTM C 1521.
<br />1.5 WARRANTY
<br />A. SPECIAL INSTALLER'S WARRANTY: INSTALLER AGREES TO REPAIR OR REPLACE JOINT SEALANTS THAT DO NOT COMPLY
<br />WITH PERFORMANCE AND OTHER REQUIREMENTS SPECIFIED IN THIS SECTION WITHIN SPECIFIED WARRANTY PERIOD.
<br />1. WARRANTY PERIOD: TWO YEARS FROM DATE OF SUBSTANTIAL COMPLETION.
<br />B. SPECIAL MANUFACTURER'S WARRANTY: MANUFACTURER AGREES TO FURNISH JOINT SEALANTS TO REPAIR, OR REPLACE
<br />THOSE JOINT SEALANTS THAT DO NOT COMPLY WITH PERFORMANCE AND OTHER REQUIREMENTS SPECIFIED IN THIS
<br />SECTION WITHIN SPECIFIED WARRANTY PERIOD.
<br />1. WARRANTY PERIOD FOR URETHANE SEALANTS: FIVE YEARS FROM DATE OF SUBSTANTIAL COMPLETION.
<br />2. WARRANTY PERIOD FOR SILICONE SEALANTS: 20 YEARS FROM DATE OF SUBSTANTIAL COMPLETION.
<br />1.6 JOINT SEALANTS, GENERAL
<br />A. COMPATIBILITY: PROVIDE JOINT SEALANTS, BACKINGS, AND OTHER RELATED MATERIALS THAT ARE COMMPATIBLE WITH
<br />ONE ANOTHER AND WITH JOINT SUBSTRATES UNDER CONDITIONS OF SERVICE AND APPLICATION, AS DEMONSTRATED BY
<br />JOINT -SEALANT MANUFACTURER, BASED ON TESTING AND FIELD EXPERIENCE.
<br />B. VOC CONTENT OF INTERIOR SEALANTS: SEALANTS AND SEALANT PRIMERS USED !INSIDE THE WEATHERPROOFING
<br />SYSTEM SHALL COMPLY WITH THE FOLLOWING:
<br />1. ARCHITECTURAL SEALANTS SHALL HAVE A VOC CONTENT OF 25C G/L OR LESS.
<br />2. SEALANTS AND SEALANT PRIMERS FOR NONPOROUS SUBSTRATES SHALL HAVE A VOG CONTENT OF 250 /L. OR I. ESS.
<br />3. SEALANTS AND SEALANT PRIMERS FOR NONPOROUS SUBSTRATES SHALL HAVE A VOC CONTENT OF 775 G/L OF LES>
<br />C. LOW -EMITTING INTERIOR SEALANTS: SEALANTS AND SEALANT PRIMER; SHALL COM PLY'.'WITH THE TESTING AND
<br />PRODUCT REQUIREMENTS OF THE CALIFORNIA DEPARTMENT OF HEALTH'S (FOR!'MEP,LI', THE CALIFORNIA DEPARTIv1EhiT OF
<br />HEALTH SERVICES') "STANDARD METHOD FOR THE TESTING AND EVALUATHON OF VOLL.71 OR^AN',C CHEMICAL 17 M'SS;ONS
<br />FROM INDOOR SOURCES USING FNVIRONMENTAL CHAMBERS."
<br />D. LIQUID -APPLIED JOINT SEALANTS: COMPLY WITH kSTM" C 920 AND CT ER n RFi?!:l �C v'F;`ITS H- ,,ATEC F0, �ACI; LIQUiD-
<br />APPLIED JOINT SEALANT SPECIFIED, INCLUDING THOSE REFERENCING ASTM, C 920 CLASSIFICAT! -NS FOR TYPE, GRADE,
<br />CLASS, AND USES RELATED TO EXPOSURE AND JOINT SUBSTRATES.
<br />E. STAIN -TEST -RESPONSE CHARACTERISTICS: WHERE SEALANTS ARE SPECIFIED TO BE NON -STAINING TO POROUS
<br />SUBSTRATES, PROVIDE PRODUCTS THAT HAVE UNDERGONE TESTING ACCORDING TO ASTM C 1248 AND HAVE NUT" STAINED
<br />POROUS JOINT SUBSTRATES INDICATED FOR PROJECT.
<br />F. COLORS OF EXPOSED JOINT SEALANTS: AS SELECTED BY ARCHITECT FROM MANUFACTURER'S FULL RANGE.
<br />1.7 GLAZING SEALANTS
<br />A. TWO-PART SILICONE ELASTOMERIC ADHESIVE/SEALANT FOR USE STRUCT URA.L'.SLA_1;NO APPL!C,T! DNS, ASTM C 920,
<br />TYPE M, GRADE NS, CLASS 25, USE G AND A.
<br />1. PRODUCTS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, PROVIDE ONE OF THE FOLLOWING OR EQUAL.
<br />a. GE ADVANCED MATERIALS - ULTRAGLAZE-SSG4600
<br />b. DOW CORNING CORPORATION; 963
<br />1.8 SILICONE JOINT SEALANTS
<br />A. SILICONE, S, INS, 100/50, NT: SINGLE -COMPONENT, NONSAG, PLUS 100 PERCENT AND MINUS 50 PERCENT MOVEMENT
<br />CAPABILITY, NONTRAFFIC-USE, NEUTRAL -CURING SILICONE JOINT SEALANT; ASTM C 920, TYPE S, GRADE NS, ,LASS 160/50,
<br />USE NT.
<br />1. DOW CORNING CORPORATION; 790.
<br />2. GE ADVANCED MATERIALS - SILICONES; SILPRUF LM SCS2700.
<br />3. PECORA CORPORATION; 890.
<br />4. SIKA CORPORATION, CONSTRUCTION PRODUCTS DIVISION; SIKASIL-C990,
<br />5. TREMCO INCORPORATED; SPECTREM 1.
<br />B. SILICONE, S, NS, 50, NT: SINGLE -COMPONENT, NONSAG, PLUS 50 PERCENT AND MINUS 50 PERCENT MOVEMENT
<br />CAPABILITY, NONTRAFFIC-USE, NEUTRAL -CURING SILICONE JOINT SEALANT; ASTM C 920, TYPE S, GRADE NS, CLASS 50, USE
<br />NT.
<br />1. DOW CORNING CORPORATION; 790
<br />2. GE ADVANCED MATERIALS - SILICONES; SILPRUF LM SCS2000
<br />1.9 URETHANE JOINT SEALANTS
<br />A. URETHANE, S, NS, 25, NT: SINGLE -COMPONENT, NONSAG, NONTRAFFIC-USE, PLUS 25 PERCENT AND MINUS 25 PERCENT
<br />MOVEMENT CAPABILITY, URETHANE JOINT SEALANT; ASTM C 920, TYPE S, GRADE NS, CLASS 2.5, USE NT.
<br />1. SIKA CORPORATION, INC.; SIKAFLEX -1A.
<br />2. BASF BUILDING SYSTEMS; SONOLASTIC NP1.
<br />3. TREMCO; VULKEM 116
<br />B. URETHANE, S, P, 25, T, NT: SINGLE -COMPONENT, POURABLE, PLUS 25 PERCENT AND MINUS 25 PERCENT MOVEMENT
<br />CAPABILITY, TRAFFIC -AND NONTRAFFIC-USE, URETHANE JOINT SEALANT; ASTM C 920, TYPE S, GRADE P, CLASS 25, USES T
<br />AND NT.
<br />1. BASF BUILDING SYSTEMS; SONOLASTIC SL 1.
<br />2 BOSTIK, INC.; CHEM-CALK 950.
<br />3. PECORA CORPORATION; UREXPAN NR-201,
<br />4. SIKA CORPORATION. CONSTRUCTION PRODUCTS DIVISION' SIKAFLEX- iCSL.
<br />5. TREMCO INCORPORATED; VULKEM 45
<br />C. URETHANE, M, NS, 25, NT: MULTICOMPONENT, NONSAG, PLUS 25 PERCENT AND MINUS 25 PERCENT MO IEMENT
<br />CAPABILITY, NONTRAFFIC-USE. URETHANE HANE JOINT SEALANT; AS7A C 920, TYfr- tit, GRADED NS, CLASS 2E, I !SE N T .
<br />1. BASF BUILDING SYSTEMS; SONOLAST!C NP 2.
<br />2. BCSTIK, INC.; CHEM-CALK 500.
<br />3. PECORA CORPORATION; DYNATROL Il.
<br />4. TREMCO INCORPORATED; DYMERiC 240,
<br />5, SIKA CORPORATION, CONSTRUCTION PRODUCTS DIVISION: SIKAFLEX - 20 NS.
<br />1.10 MILDEW -RESISTANT JOINT SEALANTS
<br />A. ' MILDEW -RESISTANT- JOINT SEALANTS: FORMULATED FOR PROLONGED EXPOSURE TO HUMIDITY WITH FUNGGCIDE TO
<br />PREVENT MOLD AND MILDEW GROWTH.
<br />B. SILICONE. MILDEW !RESISTANT, ACID CURING, S, NS, 25, NT MILDEW -RESISTANT. S!NGi-CCil.fPQNENT. NC',:SAG, PLUS 25
<br />PERCENT AND MINUS 25 PERCENT MOVEMENT CAPABILITY, NONTRAFFIC-USE, AC',DCURIN = S!L;CONE ,;C, NT SEALANT; ASTM
<br />C 920, TYPE S, GRADE NS, CLASS 25, USE NT.
<br />1. GE ADVANCED MATERIALS - SILICONES; SANITARY SCS1700 2. DOWN CORNING CORPORATION; 7M MILDEW RESISTANT
<br />2. BASF BUILDING SYSTEMS; OMNIPLUS.
<br />3. TREMCO INCORPORATED; TREMSIL 200 SANITARY.
<br />C. ACRYLIC LATEX: ACRYLIC LATEX OR SILICONIZED ACRYLIC LATEX, ASTM C 834, TYPE OP. GRADE NF.
<br />1. PECORA CORPORATION; AC-2b+.
<br />2. SONNEBORN, DIVISION OF CHEMREX INC.; SONOLAC.
<br />3. TREMCO; TREMFLEX 834.
<br />1.11 ACOUSTIC JOINT SEALANTS
<br />A. ACOUSTICAL JOINT SEALANT: MANUFACTURER'S STANDARD NONSAG, PAIN TABLE, NONSTAINING LATEX SEALANT
<br />COMPLYING WITH ASTM C 834. PRODUCT EFFECTIVELY REDUCES AIRBORNE SOUND TRANSMISSION THROUGH PERIMETER
<br />JOINTS AND OPENINGS IN BUILDING CONSTRUCTION AS DEMONSTRATED BY TESTING REPRESENTATIVE ASSEMBLES
<br />ACCORDING TO ASTM E 90. ACOUSTICAL JOINT SEALANT SHALL HAVE A VOC CONTENT OF 250 G/L OR LESS WHIEN
<br />CALCULATED ACCORDING TO 40 CFR 59, SUBPART D (EPA METHOD 24).
<br />1. PECORA CORPORATION; AC-20 FTR.
<br />2. USG CORPORATION; SHEETROCK ACOUSTICAL SEALANT.
<br />3. TREMCO; ACOUSTICAL SEALANT.
<br />1.12 BUTYL RUBBER MASTIC
<br />A. MANUFACTURER'S STANDARD BUYTL RUBBER AND POLISOBUTYLENE SEALANT, TYPE 1, COMPLYING WITH ASTM C i311.
<br />1. TREMCO; BUYTL SEALANT.
<br />2. W.R. MEADOWS; POINTING MASTIC.
<br />3. PECORA CORPORATION; BA-98.
<br />SECTION 079200 - JOINT SEALANTS (CONTINUED NEXT PAGE)
<br />1708 E Columbus Di1ve
<br />Tampa, Fler:d� 3360.4
<br />All reproduction & intellectual Property
<br />rights reserved 2017
<br />Proj", t
<br />� �3� tr �f I �C. ,� �phyI hills,
<br />FL 33542
<br />Prepared for
<br />-DWIVITA NIEE.ACALGROUP
<br />i ASSGCiPtior,I wits:
<br />�< cen["I-�
<br />�r.�.3 Asti.:..;H. cS, ;fJC.
<br />%ONTA.CT: ±EARL HEF-S
<br />1381 5TH S T
<br />SARASOTA, FL 34236
<br />PHONE: 941.955.4555
<br />GENESIS ENGINEER GRCUr, L i.0
<br />CONT; ; T . MMIKE HANDY
<br />i(J v N.:ASH:`EY DR. *900
<br />AMPA, FL
<br />-, PHONE: r,�.n,rE: 81: 3.523,EZ4r15
<br />GENESIS ENGINEER GROUP, LLC
<br />CONTACT: MIKE HANEY
<br />1000 N. ASH LEY DR. #900
<br />TAMPA PI
<br />PHONC: 813-5213455
<br />-
<br />_< ".,l
<br />Profession eai , ` '- -- -,,
<br />s
<br />,I.
<br />f; r
<br />.�. k
<br />1.
<br />"-. 3. •
<br />A .=iti � - . ... ;-
<br />:y
<br />,n'rew �,. Dohme; I, �Rf __I r.. ;,, 20 ; J
<br />15805 11:22:4 -1 Afvt
<br />No. Revision Description Data
<br />1 PERMIT AND BID SET 12/10/2018
<br />No. Revision Description Date
<br />Dravv; l , y. Vb'J Cr1e l!ed L7'J: v15V
<br />Project Number 18190
<br />Sheet Title
<br />0-riginal drawing 15 7; X 36 I_+P t?;s
<br />scale contwnts ei dravA�g
<br />Sheet Number
<br />
|